Manual.ly Logo

Zipper ZI-STM350C Manual

0.0 · 0 Ratings

PDF manual · 49 Pages

English

M: qwen/qwen3.5-flash-20260224
page

/ 49

Loading...
be756ea670ea287dac4c0c5a69ab374a4994 page d
WARTUNG
ZIPPER MASCHINEN GmbH www.Zipper-Maschinen.at 13
ZI-STM350C
9 WARTUNG
Achtung! Vor Reinigung, Wartung etc. Netzstecker ziehen!
Täglich nach Betrieb
Lassen Sie das Wasser aus der Wanne ab. Dazu den Gummistöpsel ziehen, Maschine leicht
anheben auf gegenüberliegenden Seite.
Nach jedem Gebrauch die Wasserpumpe ausreichend mit klarem Wasser
durchspülen um abgelagerte Steinstaubsedimente etc. zu entfernen!
Wird die Pumpe nicht regelmäßig nach Betrieb gesäubert, wird die Pumpe mit der Zeit verstopft.
Garantie ausgeschlossen.
Staub und Verschmutzungen sind regelmäßig von der Maschine zu entfernen. Die Reinigung
ist am besten mit einem feuchten Lappen durchzuführen.
Benutzen Sie zur Reinigung keine Lösungsmittel oder Reinigungsmittel, sondern nur Wasser.
Regelmäßig
Nicht lackierte Maschinenteile mit Antikorrosionsmittel behandeln.
Alle Verbindungsteile ölen.
Diamantblatt, Flansche auf Verscheiß prüfen.
Defekte/deformierte Blätter sind sofort zu ersetzen:
Netzstecker ziehen!
Demontieren Sie den Blattschutz
Entfernen Sie die selbstanziehende Mutter mit Gabelschlüsseln.
Entfernen Sie Mutter und Flansch.
Wenn nötig, reinigen Sie diese.
Entfernen Sie das alte Blatt und montieren Sie das neue. Achten Sie dabei auf die korrekte
Ausrichtung des Blattes.
Flansch sowie Mutter montieren, Mutter festziehen.
Achten Sie darauf, dass das Sägeblatt gerade zur Schnittlinie montiert ist, drehen Sie es zur
Kontrolle per Hand und überprüfen Sie, dass es den Blattschutz nirgends berührt.

Chat with your Zipper ZI-STM350C manual using AI

Get instant AI answers from your Zipper ZI-STM350C manual

Ask anything about the Zipper ZI-STM350C. Answers come from this manual, with the pages they are based on.

ZI-STM350C Maintenance Schedule

After every use
Drain water from the basin

Remove the rubber bung and lift the opposite side of the machine to drain dirty water after each operation.

Show in the manual (page 13)
After every use
Flush the water pump

Clean the water pump with clear water to remove stone dust sediment. Failure to do so voids warranty.

Show in the manual (page 13)
Regularly
Clean dust and dirt from machine

Remove dust and dirt using a soft scrubber or clean cloth. Do not use solvents; use only water.

Show in the manual (page 13)
Regularly
Apply anti-corrosion treatment

Treat non-lacquered machine parts with an anti-corrosion agent to prevent rust.

Show in the manual (page 13)
Regularly
Lubricate connecting parts

Oil all connection points and moving joints to ensure smooth operation.

Show in the manual (page 13)
Regularly
Inspect diamond blade and flanges

Check for wear on the diamond blade and flanges. Replace cracked or deformed blades immediately.

Show in the manual (page 13)
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend ZI-STM350C?

Yes No

Frequently Asked Questions

A

It cuts marble, granite, concrete, ceramic, and tiles using suitable diamond blades as specified in the manual.

Is this answer helpful?

A

Yes, use only in wet operation to avoid dust hazard and dust damage to the machine and operator.

Is this answer helpful?

A

2 years for hobby, 1 year for professional use starting from the date of purchase by the final consumer.

Is this answer helpful?

A

Flush with clean water after every use to prevent clogging from stone dust sediment buildup.

Is this answer helpful?

A

Yes, it supports cutting angles from 90 to 45 degrees by loosening the angle fixing lever.

Is this answer helpful?

A

Pre-assembled but feet and fences need setting and requires two people due to weight.

Is this answer helpful?

A

Replace cracked blades immediately for safety and ensure the new one matches the machine speed rating.

Is this answer helpful?

M: qwen/qwen3.5-flash-20260224

Advantages and Disadvantages

Advantages

  • Powerful 3000W motor ensures efficient cutting of hard materials like granite and concrete.
  • Wet cutting system significantly reduces dust hazards and protects the blade life.
  • Adjustable cutting angles up to 45 degrees allow for precise miter cuts.
  • Robust stand included provides necessary stability during heavy duty operations.
  • CE compliant design meets EC directivess for safety and health requirements.
VS

Disadvantages

  • Hefty weight of 72 to 88 kg makes transport and setup difficult for one person.
  • Requires water setup and drainage for every single cut operation session.
  • Only one year warranty for professional use compared to two years for hobby.
  • Standard wear parts like blades are not covered by the warranty period.
  • Risk of kickback exists if guides are not used properly during cutting.
M: qwen/qwen3.5-flash-20260224

Product Specification

Type

Construction Cut-off Saw

Power

3000W (230V)

No-load Speed

2800 RPM

Blade Diameter

13.78 inches

Cutting Depth

4.13 inches (Cutting depth at 0 degrees), 2.83 inches (Cutting depth at 45 degrees inclination)

Bevel Angle

0-45 degrees

Arbor Size

1.18 inches

Features

Fence, Wet Cutting Function, Bevel Function

Weight

163.14 lbs

Package Contents

Stand

M: qwen/qwen3.5-flash-20260224

Product Description

Professional Stone Cutting Solutions

Welcome to the ultimate guide for the Zipper ZI-STM350C Electric Construction Cut-Off Saw with Stand Manual. This powerful tool is designed for precision cutting tasks in construction and stoneworking environments. The machine features a robust 3000-watt motor capable of reaching high speeds, ensuring efficient cuts through hard materials like granite, marble, and concrete. It represents a reliable choice for contractors requiring durability.

Performance and Capabilities

With a 350-millimeter diamond blade, this saw handles cutting depths up to 120mm at a 90-degree angle. The maximum cutting length reaches 680mm, making it suitable for various stone tiles and concrete projects. It operates on standard 230-volt power at 50Hz. The water tank holds 37.8 liters, providing ample coolant for the blade during extended sessions. Users can adjust the cutting angle between 0 to 45 degrees for versatile miter cuts. The sliding table measures 535x430mm.

Safety First Guidelines

Safety is paramount during operation according to the Zipper ZI-STM350C Electric Construction Cut-Off Saw with Stand Manual. The system emphasizes wet cutting processes to avoid dust hazards and protect the blade. Operators must wear protective gear including ear protection, safety glasses, and masks. The machine includes clear safety signs and requires grounding to a 230V Schuko socket. Avoid using the saw in rain or damp conditions. Always unplug the tool before maintenance.

Assembly and Operation

The unit arrives pre-assembled but requires setup of the table feet and fences. Two people are needed to move the 72 to 88 kg weight safely. During operation, ensure the water valve is open and the blade spins freely. Feed material slowly to prevent motor overload. Keep the workspace clean to avoid kickback.

Maintenance and Warranty

Regular maintenance prevents costly damage. Clean the water basin after every use and check the blade tension. The warranty offers 2 years for hobby use and 1 year for professional use. Always use original spare parts to maintain validity. This ensures longevity and safety on your job site.

Technical Specifications

The device lists a voltage of 230V and a motor power of 3000 Watts. The idle run speed is 2800 RPM. The machine dimensions are 1150x520x1210mm. Sound pressure level is 72 dB.

Detailed Safety Instructions

Read the entire manual before starting. Never force the motor or let it stop cutting. Replace cracked blades immediately. Only use extension cables rated for outdoor use with a minimum 1.5mm squared cross-section. Ensure children stay away.

Warranty Terms

Repair or replacement by discretion of the company. Claims require dealer contact and original invoices. Wear parts are not covered. Damages from misuse void the warranty.

Important Notes

This model has an IP54 protection class for dust and splash resistance. The water pump must be flushed regularly to prevent sediment buildup. Failure to maintain the pump may void the warranty. Ensure the blade rotation matches the machine speed rating. Always keep the work surface free of tools. Replace cracked blades immediately. Check all cables for wear before plugging in. The tool comes with assembly tools and a water hose. Always store the manual with the machine for future reference.

M: qwen/qwen3.5-flash-20260224

© Copyright 2026 Manual.ly