Manual.ly Logo

Worx WX390 Manual

0.0 · 0 Ratings

PDF manual · 76 Pages

English

M: OA-GPT-54-NAN
page

/ 76

Loading...
b6758e8446c72c9ea688259aadf5414e2abd page b
Cordless Rotary Hammer EN
11
OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the
instruction book carefully.
INTENDED USE
The machine is intended for hammer drilling
in concrete, brick and stone. It is also suitable
for drilling without impact in wood, metal,
ceramic and plastic. Machines with electronic
control and right/left rotation are also suitable
for screwdriving.
OPERATION
ACTION FIGURE
Removing
The Battery
See Fig. A1
Inserting The Battery See Fig. A2
Selecting The Operating Mode See Fig. B
HAMMER DRILLING
Inserting Drill Bits See Fig. C1
Removing Drill Bits See Fig. C2
DRILLING &
SCREWDRIVING
Inserting Adaptors See Fig. D1
Inserting Bits into Chuck See Fig. D2
Removing Adaptors See Fig. D3
Removing Bits from Chuck See Fig. D4
On/Off Switch See Fig. E
Switch Lock
NOTE: The Switch Trigger
Can Be Locked In The Off
Position.
See Fig. F
Forward Rotation Control See Fig. G
Reverse Rotation Control See Fig. H
LED Light See Fig. I
Temperature Dependent
Overload Protection
/
Protection Against Deep
Discharging
/
WORKING HINTS FOR YOUR
TOOL
If your power tool becomes over heated, set
the speed to maximum and run no load for 2-3
minutes to cool the motor. SDS-plus tungsten
carbide drill bits should always be used for
concrete and masonry.
When drilling in metal, only use HSS drill bits
in good condition. Where possible use a pilot
hole before drilling a large diameter hole.
PROBLEM SOLUTION
1. REASONS FOR DIFFERENT BATTERY
PACK WORKING TIMES
Charging time problems, having not used a
battery pack for a prolonged time will reduce
the battery pack working time. This can be
corrected after several charge and discharge
operations by charging & working with your
tool. Heavy working conditions such as large
screws into hard wood will use up the battery
pack energy faster than lighter working
conditions. Do not re-charge your battery pack
below 0
o
C and above 30
o
C as this will affect
performance.
MAINTENANCE
Remove the battery pack from the tool
before carrying out any adjustment,
servicing or maintenance.
Your power tool requires no additional
lubrication or maintenance, except for the
cleaning & lubrication of the SDS bits and
adaptors before inserting into the chuck.
There are no user serviceable parts in your
power tool. Never use water or chemical
cleaners to clean your power tool. Wipe clean
with a dry cloth. Always store your power tool
in a dry place. Keep the motor ventilation slots
clean. Keep all working controls free of dust.
Occasionally you may see sparks through the
ventilation slots. This is normal and will not
damage your power tool.

Chat with your Worx WX390 manual using AI

Get instant AI answers from your Worx WX390 manual

Ask anything about the Worx WX390. Answers come from this manual, with the pages they are based on.

WX390 Maintenance Schedule

Before Use
Clean and lubricate SDS bits and adaptors

Clean and lubricate SDS bits and adaptors before inserting them into the chuck. Do not use water or chemical cleaners on the tool.

Show in the manual (page 11)
As Needed
Wipe tool with dry cloth

Wipe the tool clean with a dry cloth. Never use water or chemical cleaners. Keep motor ventilation slots and controls free of dust.

Show in the manual (page 11)
M: QW-35-FL

Ask a Question

0/1000

Do you recommend WX390?

Yes No

Frequently Asked Questions

A

It is designed for hammer drilling in concrete, brick, and stone, plus regular drilling in wood, metal, ceramic, and plastic. It can also assist with screwdriving when used with the right settings and accessories.

Is this answer helpful?

A

Yes. It is a cordless rotary hammer powered by a 20V battery platform, which makes it easier to move around a workspace and use in places without direct power access.

Is this answer helpful?

A

The maximum drilling capacity is 10 mm in steel and 13 mm in wood, concrete, and brickwork. That makes it suitable for many routine home and workshop tasks.

Is this answer helpful?

A

Not always. Some versions may include a battery, charger, keyless chuck adaptor, HSS drill bits, screwdriver bits, and SDS drill bits, but the standard contents can vary by package.

Is this answer helpful?

A

Not really. It is best for light-to-medium drilling and fastening tasks. It handles masonry drilling well, but it is not intended as a full demolition tool.

Is this answer helpful?

A

Keep the tool clean and dry, use the correct bits, remove the battery before changing accessories, and let the motor cool if it becomes too hot. Regular care helps maintain performance and safety.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • Cordless 20V PowerShare design improves mobility and reduces cable clutter.
  • Hammer drilling, standard drilling, and screwdriving add everyday versatility.
  • LED light and reverse rotation make it easier to work in tight spaces.
  • SDS-plus compatibility supports fast bit changes and solid drilling grip.
VS

Disadvantages

  • 13 mm maximum drilling capacity may limit heavier masonry tasks.
  • Noise and vibration levels mean protective gear is strongly recommended.
  • Not every accessory is included in standard packages.
  • It is better suited to light-to-medium jobs than demolition work.
M: OA-GPT-54-NAN

Product Specification

Type

Rotary hammer

No-load speed

0-900/min

No-load impact rate

0-5000/min

Drilling capacity

Steel 0.39in, Wood 0.51in

Impact energy

10.62in-lb

Tool holder

Keyless chuck, SDS-plus keyless chuck

Special features

Right/left rotation, Speed regulation, Impact rate regulation, Impact stop, LED work light, Softgrip

Weight

3.53lb

M: OA-GPT-54-NAN

Product Description

Worx WX390 H3 20V PowerShare Cordless Rotary Hammer

The Worx WX390 H3 20V PowerShare Cordless Rotary Hammer is a compact, job-ready tool made for users who want cordless freedom without giving up useful drilling power. According to the Worx WX390 H3 20V PowerShare Cordless Rotary Hammer Manual, it is designed for hammer drilling in concrete, brick, and stone, while also supporting regular drilling in wood, metal, ceramic, and plastic. With reversible rotation and electronic control, it can also help with screwdriving, making it a practical choice for mixed repair and installation work.

A major strength of this model is its balance of convenience and control. The removable battery pack keeps the workflow mobile, while the cordless format helps reduce clutter on-site and makes it easier to work in areas without nearby outlets. An LED light improves visibility in darker corners, and the forward/reverse control adds flexibility when driving screws or backing out stuck bits. The tool holder and SDS-plus setup also make bit changes more straightforward for users who switch between tasks often.

In terms of performance, the WX390 H3 is aimed at everyday drilling rather than heavy demolition. It reaches up to 0–900 rpm and 0–5000 impacts per minute, with 1.2 J of impact energy. That makes it suitable for household upgrades, fixture installation, and light renovation jobs. The maximum drilling capacity is 10 mm in steel and 13 mm in wood, concrete, and brickwork, so it covers many common applications without feeling oversized. Depending on the kit version, users may also receive a charger, battery pack, keyless chuck adaptor, HSS drill bits, screwdriver bits, and SDS bits.

The design is also supported by clear safety and maintenance guidance. Because the tool produces a noticeable 84 dB(A) sound pressure level and vibration during hammer drilling, protective gear is strongly recommended. Using the correct drill bit, keeping accessories in good condition, and allowing the motor to cool when needed all help maintain performance. For users who want a versatile cordless hammer drill with practical features and easy handling, the Worx WX390 H3 is a smart, compact solution.

Notes

  • Use SDS-plus bits for masonry and HSS bits for metal.
  • Remove the battery before changing accessories.
  • Let the motor cool briefly if the tool overheats.
  • Recycle batteries and electrical parts responsibly.
M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly