Manual.ly Logo

Worx WG385E.9 Manual

0.0 · 0 Ratings

PDF manual · 228 Pages

English

M: gpt-5.6-terra
page

/ 228

Loading...
91ecb402daa2b90e197393e6957d8eb02eaa page 8
8
Cordless Chainsaw EN
PRODUCT SAFETY
GENERAL POWER TOOL
SAFETY WARNINGS
WARNING Read all safety warnings,
instructions, illustrations and specifications
provided with this power tool.
Failure to follow
all instructions listed below may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future
reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
1. WORK AREA SAFETY
a) Keep work area clean and well lit.
Cluttered or dark
areas invite accidents.
b)
Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust.
Power tools
create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while
operating a power tool.
Distractions can cause you
to lose control.
2. ELECTRICAL SAFETY
a)
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce
risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators.
There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions.
Water entering a power tool will increase
the risk of electric shock.
d)
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts.
Damaged or entangled cords increase
the risk of electric shock
.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use.
Use of
a cord suitable for outdoor use reduces the risk of
electric shock
.
f) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply
. Use of an RCD reduces the risk of
electric shock.
3. PERSONAL SAFETY
a) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication.
A
moment of inattention while operating power tools
may result in serious personal injury.
b)
Use personal protective equipment. Always wear
eye protection.
Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking up
or carrying the tool.
Carrying power tools with your
finger on the switch or energising power tools that
have the switch on invites accidents
.
d) Remove any adjusting key or wrench before
turning the power tool on.
A wrench or a key left
attached to a rotating part of the power tool may result
in personal injury.
e)
Do not overreach. Keep proper footing and
balance at all times.
This enables better control of
the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts.
Loose clothes, jewellery or
long hair can be caught in moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used.
Use of dust
collection can reduce dust-related hazards.
h) Do not let familiarity gained from frequent use of
tools allow you to become complacent and ignore
tool safety principles.
A careless action can cause
severe injury within a fraction of a second.
4) Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application.
The correct power
tool will do the job better and safer at the rate for
which it was designed.
b) Do not use the power tool if the switch does not
turn it on and off
. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
c) Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool.
Power tools are dangerous in the hands
of untrained users.
e) Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition that
may affect the power tool’s operation
. If damaged,
have the power tool repaired before use. Many
accidents are caused by poorly maintained power
tools.
f) Keep cutting tools sharp and clean.
Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking

Chat with your Worx WG385E.9 manual using AI

Get instant AI answers from your Worx WG385E.9 manual

Ask anything about the Worx WG385E.9. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend WG385E.9?

Yes No

Frequently Asked Questions

A

It uses two Worx 20V PowerShare lithium-ion battery packs to provide 40V Max power. For reliable performance, use two matching batteries and charge them at the same time. The solo version does not include batteries or a charger.

Is this answer helpful?

A

The WG385E.9 is intended for cutting wood, including trees, trunks, branches, beams, planks, and logs. It can cut with or across the grain. It should not be used for metal, plastic, masonry, or mineral materials.

Is this answer helpful?

A

The chainsaw has a 40 cm guide bar. This length offers practical reach for garden branches, firewood preparation, and general timber cutting while remaining more manageable than a larger professional forestry saw.

Is this answer helpful?

A

Yes. Fill the 160 ml oil tank with suitable bar and chain oil before operation. The saw has automatic chain lubrication, but it must have oil in the reservoir. Running it without oil can damage the chain and guide bar.

Is this answer helpful?

A

Check the chain frequently when it is new and during use. It should lift only about half a drive link depth from the center of the guide bar. Remove both batteries before making tension adjustments and wear protective gloves.

Is this answer helpful?

A

Key features include a chain brake lever with front hand guard, a lock-out button, rear hand guard, and a low-kickback chain and guide bar design. These features support safer operation but do not replace correct technique and protective equipment.

Is this answer helpful?

M: gpt-5.6-terra

Advantages and Disadvantages

Advantages

  • 40V Max system uses two compatible 20V PowerShare batteries for cordless cutting power.
  • 40 cm guide bar and 18 m/s chain speed suit logs, branches, beams, and firewood.
  • Automatic chain lubrication and an oil level window support routine maintenance.
  • Chain brake, lock-out button, hand guards, and two-handed design add important safety features.
  • Solo configuration is cost-effective for existing Worx PowerShare battery owners.
VS

Disadvantages

  • Batteries and charger are not included, so new users need to buy them separately.
  • The saw requires two batteries and will operate according to the lower-charged battery.
  • Chain oil is not supplied and must be added before first use.
  • At 4.2 kg without batteries, it may feel substantial during extended overhead-free pruning.
  • Regular chain tension, lubrication, cleaning, and sharpening are necessary for best performance.
M: gpt-5.6-terra

Product Specification

Type

Chainsaw

Battery

40 V / 2 x 20 V, lithium-ion

Bar length

15.75 in

Chain speed

59.06 ft/s

Chain pitch

3/8"

Chain oil tank

5.41 fl oz

Features

Battery charge indicator, auxiliary handle, brushless motor, tool-free chain tensioning, automatic chain lubrication, chain brake, bumper spike

Vibration level

27.56 ft/s^2

Noise level

104 dB(A)

Weight

9.26 lb (without battery)

Included

without charger and battery

M: gpt-5.6-terra

Product Description

Worx WG385E.9 40V PowerShare Cordless Chainsaw solo - Read, Download & Print Free

The Worx WG385E.9 40V PowerShare Cordless Chainsaw solo is a capable cordless tool for cutting logs, branches, timber, and other wooden materials around the home, garden, or smallholding. It uses two 20V PowerShare batteries to deliver 40V Max power, combining cordless freedom with the performance needed for demanding outdoor cutting tasks. As a solo version, it is designed for users who already own compatible Worx PowerShare batteries and a charger.

Built for efficient wood cutting

A 40 cm guide bar provides useful reach for pruning larger branches, processing firewood, and cutting timber to length. The chain travels at up to 18 m/s, helping the saw make smooth, confident cuts when paired with a sharp, correctly tensioned chain. Its bumper spikes help anchor the saw against the wood, allowing controlled cutting with steady pressure rather than forcing the motor.

The saw is intended exclusively for wood, including trunks, branches, beams, and planks. It can cut with or across the grain, making it a flexible addition to seasonal garden maintenance and DIY timber projects. At approximately 4.2 kg without batteries, the WG385E.9 balances substantial cutting capacity with the portability expected from a cordless design.

Practical controls and maintenance features

The automatic chain lubrication system supports consistent cutting performance, while the oil level window makes it easier to check when bar and chain oil needs topping up. The 160 ml oil tank should be filled before use, since chain lubrication is essential for reducing wear and maintaining cutting efficiency.

Chain tension can be adjusted using the tensioning knob. New chains naturally stretch during initial use, so regular checks are important. Keeping the chain clean, sharp, lubricated, and correctly tensioned helps reduce strain on the bar, sprocket, and motor.

Safety-focused operation

The Worx WG385E.9 includes a chain brake lever integrated with the front hand guard to help stop the chain during kickback events. A lock-out button helps prevent accidental starting, and the saw is designed for two-handed operation. For safe use, wear eye, hearing, head, hand, and protective footwear, maintain firm footing, and avoid cutting above shoulder height, from ladders, or in unstable positions.

Notes

  • Batteries, charger, and chain oil are not included with the solo version.
  • Use two matching Worx 20V PowerShare batteries and charge them together.
  • Check chain tension regularly, especially during the first cutting sessions.
  • Fit the supplied bar cover for transport and storage.
M: gpt-5.6-terra

© Copyright 2026 Manual.ly