Manual.ly Logo

Western Digital Ultrastar DC HC330 Manual

0.0 · 0 Ratings

PDF manual · 322 Pages

English

M: QW-35-FL
page

/ 322

Loading...
170f6df5ff51531b702cf5e7e9f2259a82eb page 48
72
Western Digital Ultrastar DC HC330 SATA Product Manual
SATA Interface Power Management
The device supports both receiving host-initiated interface power management requests and initiating interface
power management. The device initiates interface power management when the device enters its power saving
mode whose power consumption is lower than Idle mode.
Low PHY Power Conditions Overview
Low PHY power conditions are PHY conditions where the PHY is in a reduced power state (e.g., has disabled circuitry
in order to reduce power). This document defines the amount of power consumed in that low PHY power condition.
The low PHY power conditions include the partial PHY power condition and the slumber PHY power condition (see
section Error! Reference source not found.).
If the partial PHY power condition is enabled and the received IDENTIFY data indicates PARTIAL mode capability,
then the PHY may generate PMREQ_P (PARTIAL) primitive sequences.
If the slumber PHY power condition is enabled and the received IDENTIFY data indicates SLUMBER mode capability,
then the PHY may generate PMREQ_S (SLUMBER) primitive sequences.
If low PHY power conditions are enabled, then the PHY may reply with a PMACK primitive sequence to accept a low
PHY power condition request.
If low PHY power conditions are supported and disabled, then the PHY shall reject a low PHY power condition request
by replying with a PMNAK primitive sequence.
Active PHY Power Condition
While in the active PHY power condition:
a) The PHY is capable of transmitting information and responding to received information; and
b) The PHY may consume more power than while the PHY is in a low PHY power condition.
Partial PHY Power Condition
The interface shall detect the OOB signaling sequence COMWAKE and COMRESET if in the Partial Interface power
management state.
While in the Partial state, the interface shall be subjected to the low-transition density bit pattern (LTDP) sequences;
the interface shall remain in the Partial state until receipt of a valid COMWAKE (or COMRESET) OOB signaling
sequence.
Power dissipation in this Partial state shall be measured or calculated to be less than the PHY Active state, but more
than the Slumber state.
The requirement for a "not-to-exceed" power dissipation limit in the Partial interface power management state is
classified as vendor specific.
Slumber PHY Power Condition
The interface shall detect the OOB signaling sequence COMWAKE and COMRESET if in the Slumber Interface
power management state.
While in the Slumber state, the interface shall be subjected to the low-transition density bit pattern (LTDP) sequences;
the interface shall remain in the Slumber state until receipt of a valid COMWAKE (or COMRESET) OOB signaling
sequence.
Power dissipation in this Slumber state shall be measured or calculated to be less than the PHY Ready state, and
less than the Partial state.
The requirement for a "not-to-exceed" power dissipation limit in the Slumber interface power management state is
classified as vendor specific.

Chat with your Western Digital Ultrastar DC HC330 manual using AI

Get instant AI answers from your Western Digital Ultrastar DC HC330 manual

Ask anything about the Western Digital Ultrastar DC HC330. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend Ultrastar DC HC330?

Yes No

Frequently Asked Questions

A

The typical max sustained transfer rate is approximately 262 MB/s, with a peak interface rate of 600 MB/s over the SATA 6Gb/s connection.

Is this answer helpful?

A

Yes, specific models like WUS721010ALE6L1 support Self-Encrypting Drive (SED) capabilities with TCG Enterprise security.

Is this answer helpful?

A

The drive uses an internal mapping table to remap defective sectors to spare areas automatically during the format process without user intervention.

Is this answer helpful?

A

The typical average seek time for read operations is 8.0 milliseconds, ensuring fast data retrieval for database applications.

Is this answer helpful?

A

While physically compatible, these drives are optimized for 24/7 enterprise use and may produce more noise than typical consumer drives.

Is this answer helpful?

A

The actuator automatically locks and parks the heads outside the disk area to prevent contact and potential damage to the media.

Is this answer helpful?

A

Yes, the SATA interface supports hot-plugging when connected to a backplane or host system that supports the feature correctly.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Massive 10TB capacity with high-speed 7200 RPM rotation for superior throughput
  • Advanced dual-stage actuator and fluid dynamic bearings ensure exceptional stability
  • Comprehensive security features including SED support and sanitize commands
  • Robust error recovery and automatic defect reallocation maintain data integrity
  • Efficient power management modes reduce energy consumption in idle states
VS

Disadvantages

  • Higher acoustic noise levels compared to lower RPM enterprise drives
  • Requires specific SATA 3.3 compliant systems for full Power Disable feature use
  • Physical dimensions limit fitment in some compact server chassis designs
  • No integrated encryption keys; relies on external key management systems
  • Limited warranty period compared to consumer-grade storage solutions
M: QW-35-FL

Product Specification

Capacity

10TB (approx. 9313.23GiB or 9.09TiB, for more information)

Form factor

3.5" (width)

Interface

SATA 6Gb/s

RPM

7200 rpm

Cache

256MB

Power consumption

9.2W (active), 8W (idle)

Noise level

38dB(A) (active), 34dB(A) (idle)

Recording method

Conventional Magnetic Recording (CMR)

Sectors

4KB with emulation (512e)

Reliability forecast

2 million hours (MTBF)

Features

Suitable for continuous operation (24/7)

Warranty

60 months

Warning/Note/Trivia

Note: Non-branded OEM/System Builder drives are in circulation. Reduced warranty coverage may apply. Manufacturer warranty can be verified via serial number.Important: For use within a RAID array, do not combine drives with different recording methods (CMR, SMR). When using SMR drives in a RAID array, ensure the RAID controller (or NAS system) is compatible with SMR drives to avoid misinterpreting the partially blocked writing behavior of SMR as a "hardware defect".Trivia: The HGST/Hitachi drive division was acquired by Western Digital WDC in 2012. In 2018, most Ultrastar models received an optical overhaul with the Western Digital corporate design. Technical data and product numbers remained unchanged.

M: QW-35-FL

Product Description

Western Digital Ultrastar DC HC330: The Backbone of Modern Data Centers

The Western Digital Ultrastar DC HC330 stands as a pinnacle of enterprise storage engineering, designed specifically for the demanding environments of hyperscale data centers and cloud computing infrastructures. With a massive 10TB capacity available in both 512e and 4Kn sector formats, this drive delivers the reliability and performance required for mission-critical applications. Operating at a robust 7200 RPM, it ensures rapid data access while maintaining energy efficiency through advanced power management features.

At the heart of the HC330 lies a sophisticated fluid dynamic bearing motor and a dual-stage actuator system. This combination allows for precise head positioning, significantly reducing seek times to an average of just 8.0 milliseconds for read operations. The drive incorporates a closed-loop actuator servo that constantly monitors error conditions, ensuring data integrity even under fluctuating operational loads. Furthermore, the inclusion of a 256MB sector buffer enhances throughput by allowing for efficient look-ahead read operations and write caching strategies.

Security and data protection are paramount in the Ultrastar DC HC330. It supports comprehensive security protocols including TCG Enterprise specifications and Self-Encrypting Drive (SED) capabilities on specific models. Features like Sanitize Device functionality allow for secure data erasure via crypto scramble or overwrite methods, ensuring sensitive information is irretrievable when drives are retired or repurposed. The drive also adheres to strict environmental standards, operating reliably within temperatures ranging from 5 to 60 degrees Celsius and supporting non-condensing humidity levels up to 90 percent.

Key Operational Highlights

The HC330 is built for longevity and continuous operation. Its automatic actuator lock mechanism secures the read/write heads during power loss, preventing physical damage. The drive features Native Command Queuing (NCQ) support, which optimizes the order of I/O requests to minimize mechanical movement and maximize speed. Additionally, the Adaptive Zone Formatting technology ensures optimal performance across the entire disk surface by adjusting recording densities dynamically.

Important Notes

  • The drive includes a Ready LED output with open-drain driver capability for status monitoring.
  • Power Disable Pin 3 support is optional and requires specific system compatibility.
  • Actual accessible capacity may vary due to operating environment and formatting.

Pros

  1. Massive 10TB capacity with high-speed 7200 RPM rotation for superior throughput.
  2. Advanced dual-stage actuator and fluid dynamic bearings ensure exceptional stability.
  3. Comprehensive security features including SED support and sanitize commands.
  4. Robust error recovery and automatic defect reallocation maintain data integrity.
  5. Efficient power management modes reduce energy consumption in idle states.

Cons

  1. Higher acoustic noise levels compared to lower RPM enterprise drives.
  2. Requires specific SATA 3.3 compliant systems for full Power Disable feature use.
  3. Physical dimensions limit fitment in some compact server chassis designs.
  4. No integrated encryption keys; relies on external key management systems.
  5. Limited warranty period compared to consumer-grade storage solutions.

Frequently Asked Questions

What is the maximum sustained transfer rate? The typical max sustained transfer rate is approximately 262 MB/s, with a peak interface rate of 600 MB/s over the SATA 6Gb/s connection.

Does the drive support self-encryption? Yes, specific models like WUS721010ALE6L1 support Self-Encrypting Drive (SED) capabilities with TCG Enterprise security.

How does the drive handle defects? The drive uses an internal mapping table to remap defective sectors to spare areas automatically during the format process without user intervention.

What is the average seek time? The typical average seek time for read operations is 8.0 milliseconds, ensuring fast data retrieval for database applications.

Can I use this drive in a home PC? While physically compatible, these drives are optimized for 24/7 enterprise use and may produce more noise than typical consumer drives.

What happens if power is lost unexpectedly? The actuator automatically locks and parks the heads outside the disk area to prevent contact and potential damage to the media.

Is the drive hot-pluggable? Yes, the SATA interface supports hot-plugging when connected to a backplane or host system that supports the feature correctly.

M: QW-35-FL

© Copyright 2026 Manual.ly