Manual.ly Logo

Wera Kraftform Series 7400 7443/12 Manual

0.0 · 0 Ratings

PDF manual · 2 Pages

English

M: gpt-5.6-terra
page

/ 2

Loading...
fa44a781c52bf30ae26c2761880e376708dc page 1
Die Einbauhinweise der Sensorhersteller sind unbedingt zu beach-
ten. Wera übernimmt keinerlei Haftung für falsche Anwendungen
der Werkzeuge. Kontaktieren Sie uns bei allen Fragen zu Service,
Re-Kalibrierung oder Reparatur unter: Tel +49(0)2 02/40 45-145
Fax +49(0)2 02/40 45-158 · [email protected].
The fitting instructions of the sensor manufacturer are to
be observed under all circumstances. Wera shall accept no
responsibility for improper usage of the tools. Please contact us
if you have any queries regarding service, recalibration or repair
under: Tel +49(0)2 02/40 45-145 · Fax +49(0)2 02/40 45-158
Se han de observar indispensablemente los avisos de montaje
de las empresas productoras del sensor. Wera no asume ninguna
responsabilidad por aplicaciones incorrectas de las herramientas.
Por favor, póngase en contacto con nosostros por cualquier pre-
gunta acerca del servicio, del recalibrado o de la reparación, bajo:
teléfono +49(0)2 02/40 45-145 · telefax +49(0)2 02/4045-158
o Internet: tor[email protected].
Il convient impérativement de respecter les indications de mon-
tage des fabricants de capteurs. Wera décline toute responsabi-
lité en cas de mauvaise utilisation des outils. Pour toute question
concernant le service, le recalibrage ou la réparation, contac-
tez-nous : par téléphone au +49 (0)2 02 / 40 45-145, télécopie
au +49 (0)2 02 / 40 45-158, ou par courrier électronique sous
Vanno rispettate assolutamente le istruzioni di montaggio dei
produttori del sensore. La Wera non si assume alcuna respon-
sabilità in caso di un uso non corretto dell’utensile. Per ulteriori
domande relative alla manutenzione, ricalibrazione o ripara-
zione, La preghiamo di contattarci: Tel. +49 02 02 / 40 45-145
Fax +4902 02/40 45-158 · [email protected].
Sensorproducenternes montageanvisninger skal ubetinget følges.
Wera overtager ingen form for ansvar for forkert anvendelse af
værktøjet. Henvend dig til os med alle spørgsmål vedrørende ser-
vice, re-kalibrering eller reparation på: Tlf. +49(0)2 02/40 45-145
fax +49(0)2 02/40 45-158 · [email protected].
De installatievoorschriften van de sensorfabrikant moeten te
allen tijde worden opgevolgd. Wera is niet aansprakelijk voor
verkeerd gebruik van de gereedschappen. Neem contact met
ons op als u vragen heeft over onderhoud, kalibratie of repa-
ratie: tel +49 (0)2 02 / 40 45-145 · fax +49 (0)2 02 / 40 45-158
4,0–8,8 Nm
7443
3,3 Nm
4,0 Nm
7463
7461
2,0 Nm
1,4 Nm
1,25 Nm
0,45 Nm
0,25 Nm
300 TX
300V
RAPIDAPTOR
TECHNOLOGY
TORQUE
TOOL
PRE-SET
TORQUE
TOOL
PRE-SET
RAPIDAPTOR
TECHNOLOGY
TORQUE
TOOL
w
e
w
e
r
Korzerter Straße 21–25
D-42349 Wuppertal
Germany
www.wera.de
www.weratools.com
www.wera-tools.co.uk
Wera Werkzeuge GmbH
Made in Czech Rep.
Don’t use as pry bar or chisel. Wear approved safety goggles and gloves.
No utilice la her ra mienta como alzaprima o cincel. Use gafas de seguridad y
guantes de protección.
Ne pas utiliser comme barre de levier ou comme burin. Portez des lunettes de
protection homologuées. Mettez des gants de protection.
Safety instructions · Instructions de sécurité · Instrucciones de seguridad:
safety.wera.de
Montageset für Reifen-
druckkontrollsysteme
Drehmomentindikatoren
Voreingestellte, einstellbare Drehmo-
mentschraubendreher
Einstellbare Drehmomentschrau-
bendreher
Destornilladores dinamométricos
ajustables
Adjustable torque screwdrivers
Pre-set adjustable torque screwdrivers Destornilladores dinamométricos
ajustables, preajustados
Destornilladores indicadores de parTorque-Indicators
Assembly set for tyre
pressure control systems
Juego de montaje para
sistemas de control de
presión del neumático
Voreingestelltes Drehmoment
Präzision: ±10 %.
Akustisches Signal
signalisiert das Erreichen des voreingestellten Drehmo-
ments. Weiteres Festziehen der Schraube ist nicht mehr
möglich.
w Manipulationsschutz durch Siegelring
Zerstörung der Versiegelung signalisiert, dass der Drehmo-
mentindikator manipuliert wurde und ein sach- und anwen-
dungsgemäßer Einsatz nicht mehr garantiert ist.
e Unbegrenztes Lösemoment
Um auch das Lösen festsitzender Schrauben zu gewähr-
leisten, ist das manuell übertragbare Lösemoment (im
Gegensatz zum Anzugsmoment) nicht begrenzt.
Mit sicherem Gri das passende Werkzeug
durch Kennzeichnung des Gris mit Schraubensymbol,
Größe und Drehmoment.
Pre-set torque
Precision: ±10 %.
Acoustic signal
This indicates that the pre-set torque value has been
reached. A further tightening of the screw is no longer
possible.
w Tamperproof thanks to a seal ring
Any destruction of the seal ring indicates that the torque
indicator has been tampered with and that a proper and
application-conform usage can no longer be ensured.
e Unlimited loosening torque
To ensure that seized screws can also be loosened,
the torque that can be applied manually (contrary to the
tightening torque) is unlimited.
The right tool, immediately at hand
The handle marking displaying a screw symbol, dimen-
sion and torque value makes it easy to nd the right torque
indicator.
Par de apriete preajustado
Precisión: ±10 %.
Una señal acústica
señaliza que se ha alcanzado el par de apriete preajus-
tado. Desde este momento ya no es posible seguir apre-
tando el tornillo.
w El anillo de sellado ofrece protección contra
manipulaciones
La destrucción del anillo de sellado señaliza que el indi-
cador de par de apriete ha sido manipulado, y que ya no
se garantiza una utilización adecuada y correcta.
e Un par de desapriete ilimitado
Para garantizar que también se puedan soltar tornillos
que estén extremamente agarrotados, el par de desaprie-
te manualmente transferible no está limitado (al contrario
de lo que pasa con el par de apriete).
La herramienta precisa a primera vista y
siempre a la mano
gracias a las marcas en el mango que indican el símbolo
de tornillo, el tamaño y el par de apriete.
w Hohe Genauigkeit!
Die einstellbaren Drehmomentschraubendreher erfüllen
die Anforderungen der Normen EN ISO 6789, BS EN
26789 in Bezug auf die Messgenauigkeit von ± 6%.
e Einstellen des Drehmomentwerts
Mit dem im Gri bendlichen Hilfswerkzeug wird der
gewünschte Drehmomentwert eingestellt. Bei jeder Dre-
hung um 180° wird der Drehmomentwert verändert, und
der Einstellring rastet fühlbar ein. Beim Erreichen des
eingestellten Drehmoments löst der Drehmomentschrau-
bendreher mechanisch aus und signalisiert dies deutlich
hör- und fühlbar. Ein weiteres Festziehen der Schraube ist
dann nicht mehr möglich.
r Ablesen des eingestellten Drehmomentwerts
Der eingestellte Drehmomentwert ist exakt oberhalb der
Ablesephase rechts oder links der Pfeilspitze abzulesen.
t Unbegrenztes Lösemoment
Um auch das Lösen festsitzender Schrauben zu gewähr-
leisten, ist das manuell übertragbare Lösemoment (im
Gegensatz zum Anzugsmoment) nicht begrenzt.
Hinweis:
Der Hersteller empehlt, dieses Werkzeug immer im
entspann ten Zustand aufzubewahren.
w High precision!
The pre-set, adjustable torque screwdrivers satisfy the
EN ISO 6789 and BS EN 26789 standards with regard to
the measuring precision of ± 6%.
e Adjustment of the torque value
The desired torque value can be adjusted with the
help of the tool located in the handle. The torque value
is changed for every turn of 180° and the adjustment
ring locks noticeably into position. When the adjusted
torque value is reached, the torque screwdriver releases
mechanically and indicates this audibly and noticeably. A
further tightening of the screw is no longer possible then.
r Reading the adjusted torque value
The adjusted torque value can be read directly above the
scale on the right or to the left of the arrowhead.
t Unlimited loosening torque
To ensure that seized screws can also be loosened,
the torque that can be applied manually (contrary to the
tightening torque) is unlimited.
Note:
The manufacturer recommends that this tool is always
stored in an unstressed state.
w ¡Enorme precisión!
Los destornilladores dinamométricos ajustables cumplen con
los requerimientos de las normas EN ISO 6789, BS EN 26789
en lo que se reere a la exactitud de medición del ± 6%.
e Ajuste del valor del par de apriete
Con ayuda del útil auxiliar que se encuentra en el mango,
se ajusta el valor del par de apriete deseado. Con cada
giro en 180° se modica el valor del par de apriete y el
anillo de ajuste encastra de forma palpable. Al alcanzar el
par de apriete preajustado, el destornillador dinamomé-
trico libera la tensión de forma mecánica y señaliza este
momento claramente, tanto con una señal acústica como
de manera palpable. A partir de este momento ya no es
posible seguir apretando el tornillo.
r La lectura del valor del par de apriete ajustado
El valor del par de apriete ajustado se lee exactamente
por encima de la fase de lectura a la derecha o a la iz-
quierda de la punta de la echa.
t Un par de desapriete ilimitado
Para garantizar que también se puedan soltar tornillos
que estén extremamente agarrotados, el par de desa-
priete manualmente transferible no está limitado (al con-
trario de lo que pasa con el par de apriete).
Aviso:
La empresa productora recomienda almacenar esta
herramienta siempre de tal forma que el mecanismo de
muelle esté libre de tensión.
w Hohe Genauigkeit!
Die voreingestellten, einstellbaren Drehmomentschrau-
bendreher erfüllen die Anforderungen der Norm EN ISO
6789 in bezug auf die Messgenauigkeit von ± 6%.
e Funktionsweise
Beim Erreichen des voreingestellten Drehmoments löst
der Drehmomentschraubendreher mechanisch aus und
signalisiert dies deutlich hör- und fühlbar. Ein weiteres
Festziehen der Schraube ist dann nicht mehr möglich.
r Unbegrenztes Lösemoment
Um auch das Lösen festsitzender Schrauben zu gewähr-
leisten, ist das manuell übertragbare Lösemoment (im
Gegensatz zum Anzugsmoment) nicht begrenzt.
t Ändern des voreingestellten Drehmoments
Der Drehmomentwert kann innerhalb des Messbereichs
verändert werden. Dazu die Kappe am oberen Ende
des Gris abnehmen und mit Hilfe eines Steckschlüs-
selschraubendrehers die Einstellmutter betätigen (7461:
Drehung um 180° ≈ 0,1 Nm; 7463: Drehung um 180° ≈
0,25 Nm). Danach mit einem handelsüblichen Drehmo-
mentprüfgerät den eingestellten Wert überprüfen und mit-
tels Kappe erneut versiegeln.
w High precision!
The pre-set, adjustable torque screwdrivers satisfy the
EN ISO 6789 standard with regard to the measuring
precision of ± 6%.
e Function
When the pre-set torque value is reached, the torque
screwdriver releases mechanically and indicates this
audibly and noticeably. A further tightening of the screw is
no longer possible then.
r Unlimited loosening torque
To ensure that seized screws can also be loosened,
the torque that can be applied manually (contrary to the
tightening torque) is unlimited.
t Changing the pre-set torque value
The torque value can be adjusted within the measuring
range. To enable this, remove the cap at the upper end of
the handle and actuate the adjustment nut with the help
of a socket wrench (7461: a turn of 180° ≈ 0.1 Nm; 7463:
a turn of 180° ≈ 0.25 Nm). Subsequently, check the newly
adjusted value with a conventional torque testing device
and seal once again by securing the cap.
w ¡Enorme precisión!
Los destornilladores dinamométricos preajustados ajusta-
bles cumplen con los requerimientos de la norma EN ISO
6789 en lo que se reere a la exactitud de medición del ± 6%.
e Funcionamiento
Al alcanzar el par de apriete preajustado, el destornillador
dinamométrico libera la tensión de forma mecánica y
señaliza este momento claramente, tanto con una señal
acústica como de manera palpable. A partir de este mo-
mento ya no es posible seguir apretando el tornillo.
r Un par de desapriete ilimitado
Para garantizar que también se puedan soltar tornillos que
estén extremamente agarrotados, el par de desapriete
manualmente transferible no está limitado (al contrario de
lo que pasa con el par de apriete).
t Es posible modicar el par de apriete preajustado
El valor del par de apriete puede ser modicado dentro del
área de medición. Para esto se ha de retirar la capucha del
extremo del mango, y con ayuda de un destornillador de
vaso se ha de girar la tuerca de ajuste (7461: giro en 180°
≈ 0,1 Nm; 7463: giro en 180° ≈ 0,25 Nm). Luego se debe
vericar el valor ajustado con ayuda de un aparato usual
de comprobación del par, y nalmente se ha de volver a
cerrar el útil poniendo la capucha nuevamente.
05 679440 001 - 00000162 - 04
±6%
w
e
r
t
t

Chat with your Wera Kraftform Series 7400 7443/12 manual using AI

Get instant AI answers from your Wera Kraftform Series 7400 7443/12 manual

Ask anything about the Wera Kraftform Series 7400 7443/12. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend Kraftform Series 7400 7443/12?

Yes No

Frequently Asked Questions

A

The Wera Kraftform Series 7400 7443 covers an adjustable tightening range of 4.0 to 8.8 Nm.

Is this answer helpful?

A

It releases mechanically and provides a clear audible and tactile signal. Further tightening is then prevented.

Is this answer helpful?

A

The adjustable torque screwdriver is stated to meet a measuring accuracy of +/- 6% under the referenced EN ISO 6789 and BS EN 26789 requirements.

Is this answer helpful?

A

Yes. The manual loosening torque is unlimited, unlike the controlled tightening torque, so seized screws can be loosened when appropriate.

Is this answer helpful?

A

Use the auxiliary tool stored in the handle. Each 180-degree turn changes the torque setting, and the adjustment ring engages noticeably.

Is this answer helpful?

A

Store it in an unstressed state to support long-term mechanism care and dependable performance.

Is this answer helpful?

M: gpt-5.6-terra

Advantages and Disadvantages

Advantages

  • Adjustable 4.0 to 8.8 Nm range supports controlled fastening for precision work.
  • Mechanical release gives audible and tactile confirmation at the selected torque.
  • Stated accuracy of +/- 6% meets EN ISO 6789 and BS EN 26789 requirements.
  • Rapidaptor 1/4 inch interface enables fast bit changes.
  • Unlimited manual loosening torque can help release seized screws.
VS

Disadvantages

  • The 4.0 to 8.8 Nm range may not suit very low or high torque applications.
  • Accuracy depends on correct adjustment, storage, and periodic calibration.
  • It must not be used as a pry bar, chisel, or general-purpose leverage tool.
  • Users must follow component and sensor manufacturer fitting instructions.
M: gpt-5.6-terra

Product Specification

Tool holder

1/4 in (0.25 in) hex (bits)

Torque

0.89-13.28 in-lb, 26.55-77.89 in-lb

Grip

Multi-component sleeve

Special features

Pistol grip

Package contents

Plastic case, 12-piece accessory set, Rapidaptor bit holder

M: gpt-5.6-terra

Product Description

Wera Kraftform Series 7400 7443/12 Torque Screwdriver 1/4 - Read, Download & Print Free

The Wera Kraftform Series 7400 7443/12 Torque Screwdriver 1/4 is designed for controlled fastening where repeatable torque and dependable handling matter. Built for professional assembly work, it helps users tighten fasteners to a selected value rather than relying on feel alone. This makes it a practical choice for service tasks, precision installations, and applications involving sensor-related components.

Controlled tightening with clear feedback

The 7443 model offers an adjustable torque range of 4.0 to 8.8 Nm. Its mechanism releases when the selected torque is reached, providing both audible and tactile feedback. Once it trips, further tightening is prevented, helping reduce the risk of overtightening sensitive screws, threads, and mounted components.

The screwdriver is designed to meet the measuring accuracy requirements of EN ISO 6789 and BS EN 26789, with a stated accuracy of +/- 6%. Torque adjustment is made using the integrated auxiliary tool in the handle. Each 180-degree turn changes the setting and produces a noticeable engagement at the adjustment ring, supporting deliberate and controlled setup.

Kraftform handling and fast bit changes

Wera Kraftform ergonomics support a secure, comfortable grip during repetitive work. The handle is marked with the drive symbol, size, and torque information, making it easier to identify the correct tool at a glance. The 1/4 inch interface and Rapidaptor technology allow bits to be exchanged quickly, helping keep workflow moving when several screw profiles are involved.

Unlike the controlled tightening function, the manually applied loosening torque is not limited. This allows the tool to assist with loosening seized screws when needed, while its torque release mechanism remains focused on safe tightening. For best long-term care, the manufacturer recommends storing adjustable torque tools in an unstressed state.

Suitable use and essential care

This torque screwdriver is intended for applications where installation requirements specify a tightening value. Always follow the fitting instructions supplied by the sensor or component manufacturer. Recalibration, servicing, and repair are important considerations for maintaining dependable torque performance over time.

Do not use the screwdriver as a pry bar or chisel. Approved safety goggles and protective gloves should be worn where the task requires them. Careful setup, correct bit selection, and proper storage help preserve the accuracy and working life of the tool.

Notes

  • Set the required torque before beginning assembly.
  • Stop tightening when the mechanical release is felt and heard.
  • Check calibration regularly in demanding professional use.
  • Use the tool only for its intended fastening applications.
M: gpt-5.6-terra

© Copyright 2026 Manual.ly