Manual.ly Logo

Webasto Pure Manual

0.0 · 0 Ratings

PDF manual · 66 Pages

English

M: QW-35-FL
page

/ 66

Loading...
e960bb56323879fb72c33dcf0aaadd4134da page 9
Webasto Pure 9
Set key-operated switch from OFF to ON:
– "Dim LED indicator" function activated.
The LED indicator changes to blue and dims in several
stages from maximum to minimum, in 3 second intervals.
After reaching the lowest dim level the LED indicator swit-
ches back to maximum.
If the key-operated switch setting is not changed
from ON to OFF within 180 seconds, the original dim
level will remain unchanged and the programming
mode will be deactivated.
Set key-operated switch from ON to OFF:
– Dim level is selected.
If the key-operated switch setting is not changed further
within 60 seconds, the selected dim level will be saved and
programming mode deactivated.
Set key-operated switch back from OFF to ON to switch
to standby mode.
9.3 Deactivate charging current limit (option 2)
The charging current limit is only activated in the
factory for a 22 kW variant.
The charging current is only limited to 20 A for
1-phase charging.
The charging current limit may only be deactivated
in compliance with country-specific regulations and
standards.
3
Programming mode activated
The LED indicator flashes white in the following sequence
once: 0.5s OFF;
0.5s ON;
0.5s OFF;
0.5s ON;
After a three second pause the LED indicator switches to
yellow for one second:
Set key-operated switch from OFF to ON:
– Activate "charging current limit" function.
The current setting is indicated in colour by the LED:
Charging current limit activated = purple
Charging current limit deactivated = light blue
If the key-operated switch setting is not changed
from ON to OFF within 60 seconds, the original
setting will remain unchanged and the programming
mode will be deactivated.
Set key-operated switch from ON to OFF:
3
Charging current limit activated:
– The 20 A limit is deactivated and the charging station
is configured to the maximum current value (see type
plate). The LED indicator changes to light blue.
3
Charging current limit deactivated:
– The 20A limit is activated. The LED indicator changes
to purple.
When the key-operated switch setting is not changed
further within 60 seconds, the selected setting will be saved
and programming mode deactivated.
Set key-operated switch back from OFF to ON to switch
to standby mode.
10 Decommissioning the product
A decomissioning shall be carried out only by an authorised
electrician.
Disconnect the power supply.
Electrically disconnect the charging station.
Disposal: see chapter 12.
11 Maintenance, cleaning, repair
11.1 Maintenance
Have maintenance carried out only by an authorised electri-
cian in accordance with local requirements.
11.2 Cleaning
DANGER
High voltages
Danger of fatal electric shock.
Never clean the charging station with a high-pressure
cleaner or similar device.
Clean the installation only with a dry cloth. Do not use
aggressive cleaning agents, wax or solvents.
11.3 Repair
Unauthorised repair of the charging station is not permit-
ted. In case of failure, the complete charging station must
be replaced.
Webasto Thermo & Comfort SE reserves the exclusive right
to perform repairs to the charging station.
The only repair to the charging station that is permitted
is to have the charging cable replaced by an authorised
electrician.
11.4 To replace the charging cable
DANGER
Hazardous voltages in the device
Danger of fatal electric shock.
The charging cable of the Webasto Pure must only
be replaced by an authorised electrician.
Before carrying out any work on the charging
station, switch off the power supply to the
charging station and secure to prevent restart
Make sure that the electrical connections are
safely isolated from the power supply.
Do not leave the charging station unattended with
the cover open.
Only use original Webasto spare parts.
Refer to the Webasto online shop for part numbers.
www.webasto-charging.com
Switch off and secure the power supply to the charging
station.
Remove cover of the connection terminals (Fig. 03).
Disconnect the electrical supply cable.
Remove the screws and washers at the bottom.
Detach the charging station from the mounting frame.
Remove cable clamp of the charging cable (Fig. 12; 1).
Disconnect PE conductor (Fig. 12: PE).
Open the maintenance flap on the back of the charging
station. (Fig. 13, 6). The cover is sealed.
Disconnect the remaining wires of the charging cable
(Fig. 13; 1-5).
Replace the charging cable.

Chat with your Webasto Pure manual using AI

Get instant AI answers from your Webasto Pure manual

Ask anything about the Webasto Pure. Answers come from this manual, with the pages they are based on.

Pure Maintenance Schedule

Before each use
Check charging station for visual damage

Inspect the charging station, cable, and coupling for visible damage before every use. Do not operate if damaged.

As needed
Clean the housing with a dry cloth

Wipe the installation only with a dry cloth. Never use high-pressure cleaners, aggressive agents, wax, or solvents.

M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend Pure?

Yes No

Frequently Asked Questions

A

No, installation and electrical connection must strictly be performed by an authorized electrician to ensure safety and compliance with local regulations.

Is this answer helpful?

A

A purple LED indicates that the charging current limit is activated, typically capping the input at 20 A for single-phase charging configurations.

Is this answer helpful?

A

Touch and hold the touch control switch for at least 10 seconds to initiate a system self-test and reset failures after they have been corrected.

Is this answer helpful?

A

Yes, it has an IP54 rating allowing use in protected outdoor areas like carports, but it should not be exposed to direct rain or high-pressure washers.

Is this answer helpful?

A

You can configure the current using DIP switches, but some models have factory limits that cannot be exceeded, such as upgrading an 11 kW unit to 22 kW.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Integrated residual direct current monitoring enhances safety against DC faults
  • Sleek black finish fits modern architectural styles seamlessly
  • DIP switches allow flexible configuration for 1-phase or 3-phase systems
  • IP54 protection class ensures durability against dust and water
  • Intuitive LED indicators provide clear visual status updates
VS

Disadvantages

  • Installation requires a certified electrician which adds initial cost
  • LED warning color cannot be dimmed unlike standby colors
  • Maximum power may be limited to 20 A for single-phase setups by default
  • Unit cannot be upgraded from 11 kW to 22 kW via software after factory config
  • Charging cable replacement is restricted to authorized professionals only
M: QW-35-FL

Product Specification

Number of Charging Points

1

Charging Mode

IEC 61851-1 (Mode 3)

Number of Phases

3-phase

Voltage

400V (AC)

Connector Type

Type 2

Connection Type

Cable 14.76ft

Installation

Wall-mounted

Authorization

Key switch

Protection Class

IP54

Dimensions

8.86x17.6x4.57in (WxHxD)

M: QW-35-FL

Product Description

Discover the Webasto Pure Black Edition Manual

The Webasto Pure Black Edition represents a pinnacle in electric vehicle charging technology, blending sleek aesthetics with robust performance. Designed for both residential and commercial environments, this charging station ensures safe, efficient, and reliable power delivery to your electric vehicle. The manual serves as your comprehensive guide to unlocking the full potential of this device, offering detailed insights into installation, operation, and maintenance without unnecessary jargon.

Operating within the strict safety parameters of IEC 61851-1 standards, the Webasto Pure utilizes advanced charge mode 3 technology. This ensures that voltage is only applied once the vehicle is securely connected, protecting both the car and the user from electrical hazards. The unit features an intuitive LED indicator system that communicates status at a glance, ranging from standby blue to active green, and fault red. Whether you are configuring it for a 1-phase or 3-phase supply, the DIP switch settings allow for precise current calibration up to 22 kW.

Safety is paramount in the design philosophy of Webasto Thermo & Comfort SE. The Pure Black Edition includes integrated residual direct current monitoring to prevent dangerous DC fault currents. Installation must be performed by a qualified electrician who can ensure proper grounding and compliance with local regulations regarding circuit breakers and RCDs. The unit is built to withstand harsh conditions with an IP54 rating, making it suitable for garages, carports, and protected outdoor areas while resisting dust and water jets.

Beyond standard charging, the Webasto Pure offers customizable features accessible through its key-operated switch. Users can enter programming mode to adjust LED brightness or deactivate the 20 A charging current limit on specific variants, provided local laws permit. The included mounting kit simplifies wall installation, ensuring the unit remains stable and secure. By adhering to the guidelines found in the Webasto Pure Black Edition Manual, owners can enjoy a seamless charging experience that prioritizes longevity, safety, and efficiency.

M: QW-35-FL

© Copyright 2026 Manual.ly