Manual.ly Logo

Webasto Pure Manual

0.0 · 0 Ratings

PDF manual · 66 Pages

English

M: QW-35-FL
page

/ 66

Loading...
e960bb56323879fb72c33dcf0aaadd4134da page 3
Webasto Pure 3
1 General information
1.1 Purpose of the document
These operating and installation instructions are part of the
product and contain information for the user to ensure safe
operation and for the authorised electrician to carry out
safe installation of the Webasto Pure charging station.
1.2 Using this document
Carefully read the operating and installation instructions
before installing and starting up the Webasto Pure.
Keep these instructions ready to hand.
Hand these instructions on to the following owner or
user of the charging station.
1.3 Intended use
The Webasto Pure charging station is designed for charging
electric vehicles in accordance with IEC 61851-1, charge
mode 3. In this charge mode, the charging station ensures:
■■
The voltage is not applied before the vehicle has been
connected correctly.
■■
The maximum power is calibrated.
The AC/DC converter is in the vehicle.
1.4 Use of symbols and highlighting
DANGER
Hazard with a high degree of risk which, if not avoi-
ded, will lead to death or serious injury.
WARNING
Hazard with a moderate degree of risk which, if not
avoided, may lead to minor or moderate injury.
CAUTION
Hazard with a low degree of risk which, if not avoi-
ded, will lead to minor or moderate injury.
The note denotes a special technical feature or
potential damage to the product.
Reference to separate documentation
Description of a precondition
Description of an action
1.5 Warranty and liability
Webasto shall not accept liability for defects or dama-
ge due to the failure to comply with the operating and
installation instructions. This liability exclusion particularly
applies to:
■■
Improper use.
■■
Installation and initial operation by a non-authorised
electrician.
■■
Repairs not carried out by a Webasto service workshop.
■■
Use of non-original spare parts.
■■
Conversion of the unit without permission from
Webasto.
2 Safety
2.1 General information
Only persons over the age of 18 are permitted to use the
charging station.
The Webasto Pure charging station has been developed,
produced, tested and documented according to the
relevant safety regulations and environmental requirements.
The device must only be used in a technically faultless
condition.
Have any faults that adversely affect the safety of persons
or of the device rectified immediately by an authorised elec-
trician in accordance with nationally applicable regulations.
It is possible that the signalling in the vehicle differs
from that described here. Always read the operating
instructions of the respective vehicle manufacturer
and always observe these.
2.2 General safety information
■■
Hazardous voltages are present within the casing.
■■
Check charging station for visual damage before
use. Do not use the charging station if damaged.
■■
Installation, electrical connection and initial ope-
ration of the charging station must only be carried
out by an authorised electrician.
■■
Do not remove the cover of the installation area
whilst in operation.
■■
Do not remove markings, warning symbols and
the rating plate from the charging station.
■■
The charging cable must only be replaced by an
authorised electrician in accordance with the
installation instructions.
■■
It is strictly prohibited to connect other equip-
ment/devices to the charging station.
■■
When not in use, store the charging cable in the
designated holder and lock the charging coupling
in the charging station. Loosely wind the charging
cable around the charger casing so that it does
not touch the ground.
■■
Make sure that the charging cable and coupling
cannot be driven over, trapped and are protected
from any other hazards.
■■
Immediately notify Webasto Customer Service
if the charging station, charging cable or the
charging coupling are damaged. Do not continue
using the charging station.
■■
The vehicle must be unoccupied during the char-
ging procedure.
■■
Prevent the charging cable and coupling from co-
ming in contact with external heat sources, water,
dirt and chemicals.
■■
Do not attach extension cables or adapters to the
charging cable.
■■
Remove the charging cable by pulling on the
charging coupling only.
■■
Never clean the charging station with a high-
pressure cleaner or similar device.
■■
Switch off electrical power when cleaning the
charging sockets in the charger coupling.

Chat with your Webasto Pure manual using AI

Get instant AI answers from your Webasto Pure manual

Ask anything about the Webasto Pure. Answers come from this manual, with the pages they are based on.

Pure Maintenance Schedule

Before each use
Check charging station for visual damage

Inspect the charging station, cable, and coupling for visible damage before every use. Do not operate if damaged.

As needed
Clean the housing with a dry cloth

Wipe the installation only with a dry cloth. Never use high-pressure cleaners, aggressive agents, wax, or solvents.

M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend Pure?

Yes No

Frequently Asked Questions

A

No, installation and electrical connection must strictly be performed by an authorized electrician to ensure safety and compliance with local regulations.

Is this answer helpful?

A

A purple LED indicates that the charging current limit is activated, typically capping the input at 20 A for single-phase charging configurations.

Is this answer helpful?

A

Touch and hold the touch control switch for at least 10 seconds to initiate a system self-test and reset failures after they have been corrected.

Is this answer helpful?

A

Yes, it has an IP54 rating allowing use in protected outdoor areas like carports, but it should not be exposed to direct rain or high-pressure washers.

Is this answer helpful?

A

You can configure the current using DIP switches, but some models have factory limits that cannot be exceeded, such as upgrading an 11 kW unit to 22 kW.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Integrated residual direct current monitoring enhances safety against DC faults
  • Sleek black finish fits modern architectural styles seamlessly
  • DIP switches allow flexible configuration for 1-phase or 3-phase systems
  • IP54 protection class ensures durability against dust and water
  • Intuitive LED indicators provide clear visual status updates
VS

Disadvantages

  • Installation requires a certified electrician which adds initial cost
  • LED warning color cannot be dimmed unlike standby colors
  • Maximum power may be limited to 20 A for single-phase setups by default
  • Unit cannot be upgraded from 11 kW to 22 kW via software after factory config
  • Charging cable replacement is restricted to authorized professionals only
M: QW-35-FL

Product Specification

Number of Charging Points

1

Charging Mode

IEC 61851-1 (Mode 3)

Number of Phases

3-phase

Voltage

400V (AC)

Connector Type

Type 2

Connection Type

Cable 14.76ft

Installation

Wall-mounted

Authorization

Key switch

Protection Class

IP54

Dimensions

8.86x17.6x4.57in (WxHxD)

M: QW-35-FL

Product Description

Discover the Webasto Pure Black Edition Manual

The Webasto Pure Black Edition represents a pinnacle in electric vehicle charging technology, blending sleek aesthetics with robust performance. Designed for both residential and commercial environments, this charging station ensures safe, efficient, and reliable power delivery to your electric vehicle. The manual serves as your comprehensive guide to unlocking the full potential of this device, offering detailed insights into installation, operation, and maintenance without unnecessary jargon.

Operating within the strict safety parameters of IEC 61851-1 standards, the Webasto Pure utilizes advanced charge mode 3 technology. This ensures that voltage is only applied once the vehicle is securely connected, protecting both the car and the user from electrical hazards. The unit features an intuitive LED indicator system that communicates status at a glance, ranging from standby blue to active green, and fault red. Whether you are configuring it for a 1-phase or 3-phase supply, the DIP switch settings allow for precise current calibration up to 22 kW.

Safety is paramount in the design philosophy of Webasto Thermo & Comfort SE. The Pure Black Edition includes integrated residual direct current monitoring to prevent dangerous DC fault currents. Installation must be performed by a qualified electrician who can ensure proper grounding and compliance with local regulations regarding circuit breakers and RCDs. The unit is built to withstand harsh conditions with an IP54 rating, making it suitable for garages, carports, and protected outdoor areas while resisting dust and water jets.

Beyond standard charging, the Webasto Pure offers customizable features accessible through its key-operated switch. Users can enter programming mode to adjust LED brightness or deactivate the 20 A charging current limit on specific variants, provided local laws permit. The included mounting kit simplifies wall installation, ensuring the unit remains stable and secure. By adhering to the guidelines found in the Webasto Pure Black Edition Manual, owners can enjoy a seamless charging experience that prioritizes longevity, safety, and efficiency.

M: QW-35-FL

© Copyright 2026 Manual.ly