Manual.ly Logo

Wagner Control Pro 250 R Manual

5.0 · 1 Ratings

PDF manual · 144 Pages

English

M: QW-35-FL
page

/ 144

Loading...
b1bd20aee07f469a1f717e87bfba9cefb988 page b
D
5
Control Pro 250 R / 350 R
Hochdruckschlauch vor jeder Benutzung gründlich überprüfen.
Beschädigten Hochdruckschlauch sofort ersetzen.
Niemals defekten Hochdruckschlauch selbst reparieren!
Scharfes Biegen oder Knicken vermeiden, kleinster Biegeradius etwa 20 cm.
Hochdruckschlauch nicht überfahren, sowie vor scharfen Gegenständen und Kanten schützen.
Niemals am Hochdruckschlauch ziehen, um das Gerät zu bewegen.
Hochdruckschlauch nicht verdrehen.
Hochdruckschlauch nicht in Lösemittel einlegen. Außenseite nur mit einem getränkten Tuch abwischen.
Hochdruckschlauch so verlegen, dass keine Stolpergefahr besteht.
Elektrostatische Auadung von Spritzpistole und Hochdruckschlauch wird über den Hochdruckschlauch abgeleitet. Deshalb
muss der elektrische Widerstand zwischen den Anschlüssen des Hochdruckschlauchs gleich oder kleiner 197 kΩ/m (60 kΩ/ft.)
betragen.
i
Aus Gründen der Funktion, Sicherheit und Lebensdauer, nur WAGNER-Original-Hochdruckschläuche und
Spritzdüsen verwenden. Übersicht siehe „Ersatzteilliste”.
i
Bei alten Hochdruckschläuchen steigt das Risiko von Beschädigungen.
Wagner empehlt den Hochdruckschlauch nach 6 Jahren auszutauschen.
Anschluss des Gerätes
Der Anschluss muss über eine vorschriftsmäßig geerdete Schutzkontakt-Steckdose erfolgen. Der Anschluss muss mit einer
Fehlerstromschutzeinrichtung INF ≤ 30 mA ausgerüstet sein.
Gerät aufstellen
Gefahr
Bei Arbeiten in Räumen:
Im Bereich des Gerätes dürfen sich keine lösungsmittelhaltigen Dämpfe bilden. Aufstellen des Gerätes
auf der vom Spritzobjekt abgewandten Seite. Mindestabstand 5 m zwischen Gerät und Spritzpistole ist
einzuhalten.
Bei Arbeiten im Freien:
Es dürfen keine lösungsmittelhaltige Dämpfe zum Gerät hin getrieben werden. Windrichtung beachten.
Das Gerät so aufstellen, dass keine lösungsmittelhaltigen Dämpfe zum Gerät gelangen und sich dort
ablagern. Mindestabstand 5 m zwischen Gerät und Spritzpistole ist einzuhalten.
Wartung und Reparaturen
Gefahr
Vor allen Arbeiten am Gerät Druckentlastung durchführen und den Netzstecker aus der Steckdose ziehen.
Gerätereinigung
Gefahr
Kurzschlussgefahr durch eindringendes Wasser!
Gerät niemals mit Hochdruck- oder Dampfhochdruckreiniger abspritzen.
Gerätereinigung mit Lösemittel
Gefahr
Bei Gerätereinigung mit Lösemittel darf nicht in einen Behälter mit kleiner Önung (Spundloch) gespritzt oder
gepumpt werden. Gefahr durch Bildung eines explosionsfähigen Gas-/Luftgemisches. Der Behälter muss geerdet
sein.
Verwenden Sie zur Reinigung keine brennbaren Materialien.
Erdung des Spritzobjekts
Das zu beschichtende Spritzobjekt muss geerdet sein.

Chat with your Wagner Control Pro 250 R manual using AI

Get instant AI answers from your Wagner Control Pro 250 R manual

Ask anything about the Wagner Control Pro 250 R. Answers come from this manual, with the pages they are based on.

Control Pro 250 R Maintenance Schedule

Before each use
Check high-pressure hose for damage

Thoroughly inspect the high-pressure hose before every use. Replace immediately if damaged to prevent injection injuries.

Show in the manual (page 11)
After each use
Clean device and filters

Clean the unit immediately after finishing work using water or suitable solvent. Remove and clean nozzle, gun filter, and suction filter.

Show in the manual (page 16)
After cleaning
Preserve pump with oil

Immerse inlet valve in conservation agent (e.g., household oil) and run pump briefly to preserve it during storage.

Show in the manual (page 17)
Every 6 years
Replace high-pressure hose

Wagner recommends replacing the high-pressure hose after 6 years due to increased risk of damage from aging.

Show in the manual (page 11)
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend Control Pro 250 R?

Yes No
0
User Pic

Daniel Robinson

4 months ago

Is the Airless Wagner pump reliable and worth recommending for professional use?

0
User Pic

Manual.ly

4 months ago

Yes, based on customer feedback, the Airless Wagner pump is highly recommended. Users describe it as a top-tier product with excellent performance and durability. It is suitable for professional applications and delivers consistent results.

M: QW-35-FL
M: QW-35-FL
0
User Pic

error17

6 months ago

Does this model come with all necessary accessories for immediate setup?

M: QW-35-FL

Frequently Asked Questions

A

It handles interior latex paints, dispersions, water-based and solvent-containing lacquers, glazes, oils, and anti-rust paints. It cannot process materials with abrasive components or strong acids.

Is this answer helpful?

A

Secure the gun trigger, turn the pressure regulator to zero, switch the selector to PRIME, then unlock the gun and pull the trigger over a container until fluid stops flowing.

Is this answer helpful?

A

No, the device should never be used to spray flammable substances or in environments where explosive gases or dusts may be present due to spark generation risks.

Is this answer helpful?

A

Wagner recommends replacing the high-pressure hose after six years of use to ensure safety and prevent leaks caused by wear and tear.

Is this answer helpful?

A

The maximum permissible operating pressure is 11 MPa, which equals 110 bar, as indicated on the device rating plate.

Is this answer helpful?

A

Yes, interior wall paints can be diluted by 0-10% and other materials like wood preservatives by 5-10%, but always follow manufacturer recommendations.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Handles both thick and thin coatings like latex paint and lacquers
  • Includes HEA filter set to reduce nozzle clogging significantly
  • Thermal release protection prevents motor damage from overheating
  • Ideal for large interior and exterior surfaces due to high flow rate
  • Intuitive controls with clear PRIME and SPRAY switch positions
VS

Disadvantages

  • Requires strict adherence to grounding protocols for safety
  • High-pressure hoses must be replaced every six years for safety
  • Not suitable for highly abrasive materials or acidic substances
  • Maintenance requires careful cleaning to avoid warranty voids
  • Can generate significant overspray if technique is not practiced
M: QW-35-FL

Product Specification

Power

550W

Flow Rate

1250ml/min

Color Cup

No

Features

Airless

Weight

15.65lbs

Package Contents

2x Nozzle Set, Hose (29.53ft)

M: QW-35-FL

Product Description

Unlock Professional Painting Results with the Wagner Airless Sprayer Control Pro 250 R

The Wagner Airless Sprayer Control Pro 250 R Electro Paint Spray System represents a significant leap forward in home improvement and professional finishing. Designed for users who demand efficiency and precision, this unit transforms the often tedious task of painting into a streamlined, high-performance experience. Whether you are tackling large interior walls, exterior fences, or intricate trim work, this sprayer delivers a smooth, even coat that brush and roller simply cannot match.

At the heart of the Control Pro 250 R is a powerful piston pump capable of handling a wide variety of materials. From thick interior latex paints and stains to thinner lacquers and oils, the system adapts seamlessly. The adjustable pressure regulator allows you to fine-tune the output based on the viscosity of your coating material, ensuring optimal atomization without overspray. This versatility makes it an ideal choice for renovators who need one machine to handle multiple projects throughout the year.

Safety is paramount when dealing with high-pressure equipment, and Wagner has integrated robust safety features into the design. The system includes a thermal release mechanism that automatically shuts down the unit if overheating occurs, preventing damage and ensuring user safety. Furthermore, the device requires proper grounding to mitigate electrostatic risks, a critical feature when working with solvent-based materials. The included HEA filter set helps minimize nozzle clogging, reducing downtime and maintenance frustration.

Operation is intuitive, featuring a simple selector switch to toggle between Prime mode for priming the system and Spray mode for actual application. The ergonomic carry handle and compact footprint make storage and transport easy, while the long high-pressure hose provides ample reach for covering large areas without constant repositioning. By combining durability, ease of use, and superior finish quality, the Wagner Control Pro 250 R stands out as a top-tier solution for anyone looking to achieve professional-grade results on their next painting project.

M: QW-35-FL

© Copyright 2026 Manual.ly