Manual.ly Logo

Vitavia Planet 6200 Manual

0.0 · 0 Ratings

PDF manual · 52 Pages

English

M: QW-35-FL
page

/ 52

Loading...
0d63d1bb84a23c191f6fac2f93765ec83898 page 5
5
Push the door gliders (1014) onto both ends of
door bar (1360) (5.1).
Assemble the door as shown in diagram 5.
Connect door rollers (1015) to the door bar
(1362) using bolt (1304), washer (1009) and
nut (1007) (5.4). Bolt door bar (1362) to upper
bar (1359) (5.3) and slide the door seal (1021)
into both side bars (1358) (5.5).
Slide bolts (1500) into the bottom of the bolt
channel holding brush seals (1021) and x it in
place using nut (1515) (5.6). Cut the door
seals (1021) to length.
The door rollers can now slide into door
runner bar (1347) (5.7). Please ensure that the
door gliders are also running on the bottom
track (5.8).
Once the door is correctly in place, connect a
nut and bolt into the open end of door runner
bar (1347) as door stopper.
Adjust the door so that it moves freely.
6. ROOF VENTS
Connect the side bars (1065) and the top bar
(1064) depending on the glass thickness.
Up to 4 mm, see (6.1). For 4 mm and over,
see (6.2).
Place the bolts to connect the bottom bar
(1066) in the prepared holes, and then slide
the glass into the tracks in side bars (1065)
(6.3).
Now connect bottom bar (1066), and ensure
that the window is totally square before tighte-
ning all bolts.
Position the window in the ridge bar from one
end (6.4) and (6.5) and slide it to the required
position (6.6).
Connect the window sill (1063) with the extra
bolts in the roof bars (6.7).
Bolt the window opener (1067) to the bottom
bar (1066) using screws (1006) (6.8).
Place the plastic cap (1019) over the end of
the window opener (6.6) and connect both
window xers (1016) onto the window sill
(1063) using screws (1006) (6.8).
7. GLAZING – CLEAR GLASS
Please note the already mentioned safety
precautions.
Press the glazing seals (1020) onto the alumi-
nium proles (7.3) and cut to length.
On the roof begin by positioning the glass at
the eave and x in place using the glazing
spring clips (1011) (7.2). The following pane
should be placed over the pane directly under
it and held in place with the glass retaining
clips (1012) between the panes (7.1).
On the sides please begin from the bottom.
If you’ve chosen polycarbonate sheets instead
of glass panes, please use the instruction in-
cluded in the box with the polycarbonate
sheets.
FINISHING
If desired, it is possible to seal the greenhouse
at the edges using neutral silicone. Silicone is
not in cluded.
Place the warning label inside the house.
A full range of accessories is available to help
you make the most of this product. Please
contact your local stockist for details.
SAFETY NOTICE
In the event of high winds, close all doors and
vents.
In the event of heavy snowfall, clear the roof
of the building or take suitable measures to
support the roof. Heat the building in winter.
COMMENTS
For the complete protection of your new
greenhouse, we advise you to include it in
your house insurance. Please take note of
possible building rules relating to the position-
ing of greenhouses.
Please stick the greenhouse model label pro-
vided onto the door bar (1362) after success-
fully assembling this product. This information
is important in the event that replacement
parts are later required.
Please keep these Assembly Instructions in
a safe place, for future reference!
Our policy is one of continuous improvement
and we reserve the right to change the speci-
cations without prior notice.
005.01.1703

Chat with your Vitavia Planet 6200 manual using AI

Get instant AI answers from your Vitavia Planet 6200 manual

Ask anything about the Vitavia Planet 6200. Answers come from this manual, with the pages they are based on.

Planet 6200 Maintenance Schedule

Occasionally
Wash the greenhouse with a gentle detergent

Thoroughly wash the greenhouse occasionally using a mild detergent that does not react aggressively with aluminium or glass fixing clips.

Regularly
Clean the door tracks

Ensure that the upper and lower door tracks are cleaned regularly to avoid a build up of debris.

As needed
Lubricate door tracks

Door tracks should be regularly cleaned and lubricated with paraffin wax or graphite.

Show in the manual (page 12)
Seasonally
Remove leaves from roof

Regularly remove leaves and dirt from the roof to prevent blockages and damage.

Show in the manual (page 23)
Periodically
Check ground anchoring

Continuously check that the anchoring into the ground is holding firmly.

Show in the manual (page 23)
Before storms
Close doors and vents in high wind

In the event of high winds, close all doors and vents. Manually close automatic vent openers if strong wind is forecast.

During snowfall
Clear snow from roof

In the event of heavy snowfall, clear the roof of the building or take suitable measures to support the roof.

Annually
Heat the building in winter

Heat the building in winter to maintain structure integrity and plant conditions.

M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend Planet 6200?

Yes No

Frequently Asked Questions

A

Select a sunny location that is sheltered from the wind as much as possible. Place it on a flat surface below the frost level. Avoid exposed spots that receive strong gusts.

Is this answer helpful?

A

You will need normal and crosshead screwdrivers, a 10 mm socket spanner or wrench, a combination spanner, a knife, a measuring stick, a spirit level, and an accu-drill with adjustable torque settings.

Is this answer helpful?

A

Yes, polycarbonate sheets are compatible. However, you must follow the specific instructions included in the box with the polycarbonate sheets rather than the standard glass instructions.

Is this answer helpful?

A

Wash thoroughly with a gentle detergent occasionally. Ensure the detergent does not react aggressively with aluminium or fixing clips. Clean upper and lower door tracks regularly to avoid debris buildup.

Is this answer helpful?

A

Yes, the greenhouse must always be anchored. For very windy locations, drill through the base profile and steel base to connect them with nuts and bolts securely.

Is this answer helpful?

A

Close all doors and vents immediately. Do not leave automatic openers active. Clear snow loads quickly to prevent roof damage and consider supporting the roof in heavy snow conditions.

Is this answer helpful?

A

It is recommended to include the greenhouse in your house insurance policy for full protection against potential weather events like hailstorms or extreme wind damage.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Sturdy aluminium frame design allows for long term durability.
  • Clear glass or polycarbonate options suit different plant needs.
  • Roof vents provide necessary ventilation for healthy growth.
  • Sliding doors save space and improve accessibility easily.
  • Zinc coated steel base available for added wind resistance.
VS

Disadvantages

  • Assembly requires two people to ensure safety standards.
  • Base foundation must be perfectly square and level.
  • Maximum bolt torque is limited to 3Nm carefully.
  • Sharp edges exist on aluminium profiles requiring caution.
  • Harsh chemicals can damage aluminium or fixing clips.
M: QW-35-FL

Product Specification

Glazing

Polycarbonate 0.24 in (Multi-wall panel)

Frame

Aluminum

Color

Black

Area

53.82 sq ft

Features

2 Roof windows, gutter, lockable

Door

Sliding door

Dimensions (LxWxH)

76.77x127.17x81.50 in

Weight

114.20 lbs

Package Contents

Steel foundation

M: QW-35-FL

Product Description

Building Your Dream Garden Space

Welcome to the ultimate guide for expanding your gardening horizons with the stunning Vitavia Planet 6200 HKP 6mm Greenhouse Black. This structure is designed to provide an optimal environment for cultivating plants year-round while maintaining durability against the elements. Following the Vitavia Planet 6200 HKP 6mm Greenhouse Black Manual is crucial for a successful setup. The best location provides maximum sunlight yet remains sheltered from strong winds. Placing your greenhouse correctly is the first step toward longevity.

Assembly Essentials

Constructing this unit requires patience and precision. It is highly recommended that two people work together during the assembly phase to ensure safety and structural integrity. Before starting, verify that every single part listed in the packing slip is present. Lay out all components neatly to avoid mixing bundles. The frame relies on aluminium profiles which can have sharp edges, so wear protective gear like gloves and safety glasses. When tightening bolts, adhere strictly to the maximum torque of 3Nm to prevent damage to the threads or profile. Do not force components if fitting problems arise.

Structure and Glazing

The design allows for flexibility with glazing options. Polycarbonate sheets are also compatible if handled according to specific guidelines. Roof vents provide essential airflow, controlled manually using window openers installed in the ridge bar. Doors glide smoothly on runners, but care must be taken not to rest the door on the gliders when fully assembled. Foundation work is critical for stability. The base must be perfectly square and level. If using soil, ensure depth goes below the frost line to prevent shifting. A zinc-coated steel base accessory is available for added stability in windy areas.

Care and Safety

Regular maintenance keeps your greenhouse functioning perfectly throughout the changing seasons. Wash panels occasionally with gentle detergents avoiding aggressive chemicals that could harm aluminium or clips. Clean tracks regularly to prevent debris buildup which hinders sliding. During high winds, ensure all doors and vents are closed tightly. Remove heavy snow loads promptly to protect the roof structure from collapse. Always include the greenhouse in your home insurance policy for complete protection against weather events. Following these detailed Vitavia Planet 6200 HKP 6mm Greenhouse Black Manual steps ensures years of productive growing seasons for your beloved plants without compromising safety. Store the label on the door bar for future repair orders.

Notes: Ensure foundations are treated to resist rot. Apply silicone at joints if total sealing is desired. Keep identification stickers visible for future spare part orders. Do not heat if unnecessary.

M: QW-35-FL

© Copyright 2026 Manual.ly