Manual.ly Logo

Victron Energy Quattro Manual

0.0 · 0 Ratings

PDF manual · 162 Pages

English

M: QW-35-FL
page

/ 162

Loading...
2505bcc077b750fbe77041b76df1c580d5a1 page 3
1
EN NL FR DE ES SE Appendix
NOTE:
This manual is intended for products with firmware xxxx400 or higher (with x any number)
The firmware number can be found on the microprocessor, after removing the front panel.
It is possible to update older units, as long as that same 7 digit number starts with either 26 or 27. When it starts with 19 or 20
you have an old microprocessor and it is not possible to update to 400 or higher.
1. SAFETY INSTRUCTIONS
In general
Please read the documentation supplied with this product first, so that you are familiar with the safety signs en directions before
using the product.
This product is designed and tested in accordance with international standards. The equipment should be used for the
designated application only.
WARNING: DANGER OF ELECTRICAL SHOCK
The product is used in combination with a permanent energy source (battery). Even if the equipment is switched off, a
dangerous electrical voltage can occur at the input and/or output terminals. Always switch the AC power off and disconnect the
battery before performing maintenance.
The product contains no internal user-serviceable parts. Do not remove the front panel and do not put the product into
operation unless all panels are fitted. All maintenance should be performed by qualified personnel.
Never use the product at sites where gas or dust explosions could occur. Refer to the specifications provided by the
manufacturer of the battery to ensure that the battery is suitable for use with this product. The battery manufacturer's safety
instructions should always be observed.
WARNING: do not lift heavy objects unassisted.
Installation
Read the installation instructions before commencing installation activities.
This product is a safety class I device (supplied with a ground terminal for safety purposes). Its AC input and/or output
terminals must be provided with uninterruptable grounding for safety purposes. An additional grounding point is
located on the outside of the product. If it can be assumed that the grounding protection is damaged, the product should be
taken out of operation and prevented from accidentally being put into operation again; contact qualified maintenance personnel.
Ensure that the connection cables are provided with fuses and circuit breakers. Never replace a protective device by a
component of a different type. Refer to the manual for the correct part.
Check before switching the device on whether the available voltage source conforms to the configuration settings of the product
as described in the manual.
Ensure that the equipment is used under the correct operating conditions. Never operate it in a wet or dusty environment.
Ensure that there is always sufficient free space around the product for ventilation, and that ventilation openings are not
blocked.
Install the product in a heatproof environment. Ensure therefore that there are no chemicals, plastic parts, curtains or other
textiles, etc. in the immediate vicinity of the equipment.
Transport and storage
On storage or transport of S product, ensure that the mains supply and battery leads are disconnected.
No liability can be accepted for damage in transit if the equipment is not transported in its original packaging.
Store the product in a dry environment; the storage temperature should range from –20°C to 60°C.
Refer to the battery manufacturer's manual for information on transport, storage, charging, recharging and disposal of the
battery.

Chat with your Victron Energy Quattro manual using AI

Get instant AI answers from your Victron Energy Quattro manual

Ask anything about the Victron Energy Quattro. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend Quattro?

Yes No

Frequently Asked Questions

A

The Quattro combines an inverter, battery charger, and automatic transfer switch. It manages power from multiple sources like generators and shore power while providing uninterrupted power to loads.

Is this answer helpful?

A

Yes, the Quattro has two AC inputs allowing you to connect two independent sources, such as two generators or a generator and mains supply. It automatically switches between them based on availability.

Is this answer helpful?

A

PowerAssist supplements limited input current with power from the battery bank. If your generator or shore power cannot meet peak demand, the Quattro adds extra power from the batteries to prevent overload.

Is this answer helpful?

A

Absolutely. It works seamlessly with solar inverters, managing excess energy to charge batteries and shutting down solar inverters via frequency shift when batteries are fully charged.

Is this answer helpful?

A

Yes, you can connect up to six identical Quattro units in parallel to increase total power output or configure them for three-phase operation.

Is this answer helpful?

A

If the battery voltage drops below the safe threshold, the inverter will switch off to protect the battery. The 'Low Battery' LED will illuminate or flash depending on the severity.

Is this answer helpful?

A

Basic settings can be changed with DIP switches, but for full configuration including parallel setups, the VEConfigure software is recommended.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Dual AC inputs allow flexible connection of generators and shore power
  • PowerAssist feature extends generator capacity and reduces fuel consumption
  • Seamless UPS functionality prevents interruptions for sensitive electronics
  • Adaptive four-stage charging maximizes battery lifespan
  • Supports parallel and three-phase configurations for scalable power needs
VS

Disadvantages

  • Requires specific firmware versions (xxxx400+) for advanced features
  • Installation must be performed by qualified electrical engineers
  • No internal DC fuse; external fusing is mandatory for safety
  • Complex configuration may require software tools for optimal setup
  • Higher initial cost compared to basic inverters or chargers
M: QW-35-FL

Product Specification

Note

Prices include 0% VAT rates for AT and DE in some cases

Type

Battery inverter, with fan

Input

Terminals

Ambient temperature

-40°F to +149°F

M: QW-35-FL

Product Description

Victron Energy Quattro 3 kVA - 15 kVA (230V Sinus) Manual: The Ultimate Power Solution

The Victron Energy Quattro is a versatile powerhouse designed for those who demand reliability and efficiency in their energy systems. This device combines a high-performance sine wave inverter, a powerful battery charger, and an automatic transfer switch into one compact unit. Whether you are setting up an off-grid cabin, a mobile home, or an industrial backup system, the Quattro provides seamless power management.

One of the standout features of the Quattro is its dual AC input capability. You can connect two independent voltage sources, such as a generator and shore power, or two different generators. The system intelligently selects the best available source, ensuring your devices stay powered without interruption. If both inputs are active, it prioritizes the first input, which is typically where a generator is connected.

The Quattro also excels with its PowerControl and PowerAssist functions. PowerControl allows you to set maximum current limits on your AC inputs, preventing overload on your generator or shore connection while maximizing charging speeds. PowerAssist takes this further by supplementing limited shore current or generator output with power from your batteries during peak demands. This means you can run heavy appliances like washing machines or air conditioners even with a small generator or limited shore power.

For solar enthusiasts, the Quattro integrates perfectly with photovoltaic systems. It manages excess solar energy by charging batteries and shuts down solar inverters when batteries are full using frequency shifting technology. With support for parallel operation of up to six units, you can scale your system to deliver massive power outputs suitable for large installations.

Safety is paramount, with built-in protections against overloads, low battery voltage, and excessive temperatures. The device features programmable relays and digital ports that allow for advanced customization, including starter relay functions for generators and communication with battery management systems. Its adaptive four-stage charging ensures optimal battery life across various battery types, from lead-acid to lithium-ion.

Notes

  • Ensure all firmware is version xxxx400 or higher for full functionality.
  • Always use qualified personnel for installation and maintenance.
  • Maintain at least 10 cm of clearance around the unit for proper ventilation.
M: QW-35-FL

© Copyright 2026 Manual.ly