Manual.ly Logo

Victron Energy Phoenix Inverter 24/3000 Manual

0.0 · 0 Ratings

PDF manual · 26 Pages

English

M: QW-35-FL
page

/ 26

Loading...
aaf529e8fb030427f7b088fb7970ba26adcb page 12
6. MAINTENANCE
The Phoenix Inverter does not require specific maintenance. It will suffice to check all
connections once a year. Avoid moisture and oil/soot/vapours, and keep the device
clean.
7. FAULT INDICATIONS
With the procedures below, most errors can be quickly identified. If an error cannot be
resolved, please refer to your Victron Energy supplier.
7.1 General error indications
Problem
Cause
Solution
Inverter operation not
initiated when
switched on.
The battery voltage is excessively
high or too low. No voltage on DC
connection.
Ensure that the battery voltage is
within the correct range.
“Low battery” LED
flashes.
The battery voltage is low.
Charge the battery or check the
battery connections.
“Low battery” LED
lights.
The converter switches off
because the battery voltage is too
low.
Charge the battery or check the
battery connections.
“Overload” LED
flashes.
The converter load is higher than
the nominal load.
Reduce the load.
“Overload” LED
lights.
The converter is switched off due
to excessively high load.
Reduce the load.
“Temperature” LED
flashes or lights.
The environmental temperature is
high, or the load is too high.
Install the converter in cool and
well-ventilated environment, or
reduce the load.
“Low battery” and
“overload” LEDs
flash intermittently.
Low battery voltage and
excessively high load.
Charge the batteries, disconnect
or reduce the load, or install
higher capacity batteries. Fit
shorter and/or thicker battery
cables.
“Low battery” and
“overload” LEDs
flash simultaneously.
Ripple voltage on the DC
connection exceeds 1,5Vrms.
Check the battery cables and
battery connections. Check
whether battery capacity is
sufficiently high, and increase
this if necessary.
“Low battery” and
“overload” LEDs
light.
The inverter is switched off due to
an excessively high ripple voltage
on the input.
Install batteries with a larger
capacity. Fit shorter and/or
thicker battery cables, and reset
the inverter (switch off, and then
on again).
One alarm LED lights
and the second
flashes.
The inverter is switched off due to
alarm activation by the lighted
LED. The flashing LED indicates
that the inverter was about to
switch off due to the related alarm.
Check this table for appropriate
measures in regard to this alarm
state.

Chat with your Victron Energy Phoenix Inverter 24/3000 manual using AI

Get instant AI answers from your Victron Energy Phoenix Inverter 24/3000 manual

Ask anything about the Victron Energy Phoenix Inverter 24/3000. Answers come from this manual, with the pages they are based on.

Phoenix Inverter 24/3000 Maintenance Schedule

Remind me when maintenance is due
Yearly
Check all connections

The manual states that specific maintenance is not required, but it suffices to check all connections once a year.

Show in the manual (page 18)
As needed
Keep device clean and dry

Avoid moisture and oil/soot/vapours, and keep the device clean.

Show in the manual (page 18)

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend Phoenix Inverter 24/3000?

Yes No

Frequently Asked Questions

A

Yes, you can connect up to six identical Phoenix Inverter units in parallel to increase total power output. They can also be configured for three-phase operation using standard RJ45 cables.

Is this answer helpful?

A

The Victron Energy Phoenix Inverter produces a true sine wave output, which is essential for powering sensitive electronics and motors without noise or overheating issues.

Is this answer helpful?

A

You must use DIP switches to set one unit as the master and others as slaves. All units must be interconnected with UTP cables and powered on in sequence after settings are stored.

Is this answer helpful?

A

The enclosure has an IP 21 rating, protecting against dripping water and solid objects larger than 12mm. It should be installed in a dry environment away from direct weather exposure.

Is this answer helpful?

A

The inverter will automatically shut down to protect the battery from deep discharge. The low battery LED will illuminate to indicate the cause of the shutdown.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Superior start-up power handles difficult loads like motors and compressors effortlessly
  • True sine wave output protects sensitive electronic equipment from damage
  • Supports parallel connection of up to six units for scalable power solutions
  • Compact and lightweight design utilizes advanced hybrid HF technology
  • High efficiency rating of up to 94% maximizes battery life and performance
VS

Disadvantages

  • Requires installation by a qualified electrical engineer due to safety class requirements
  • Parallel and three-phase configurations need specific configuration steps and identical units
  • Not suitable for delta three-phase configurations, only wye connections allowed
  • Ventilation space must be maintained to prevent thermal shutdown under heavy load
  • DIP switch settings require careful handling to avoid system errors during setup
M: QW-35-FL

Product Specification

Note

Prices may include 0% VAT rates for AT and DE

Type

Battery inverter, with fan

Input voltage

19-33V DC

Output power

3kW

Efficiency

94.00% max.

Input

Terminals

Protection class

IP21

Ambient temperature

-40F to +149F

Dimensions

10.16x14.25x8.58in (WxDxH)

Weight

39.68lbs

M: QW-35-FL

Product Description

Powering Your World with the Victron Energy Phoenix Inverter

The Victron Energy Phoenix Inverter 24/3000 (120V Sinus) represents a pinnacle of engineering designed for professional duty. This device transforms direct current from batteries into a pure sine wave alternating current, ensuring that sensitive electronics and demanding appliances operate smoothly without interference. Built with hybrid HF technology, it delivers superior efficiency within a compact, lightweight chassis, making it an ideal choice for marine, automotive, and off-grid applications where space and weight are critical factors.

One of the standout features of this inverter is its exceptional start-up power capability. Unlike conventional high-frequency inverters, the SinusMax technology allows it to handle difficult loads such as electric motors, compressors, and pumps with ease. Whether you are running a refrigerator compressor or starting a heavy-duty motor, the Phoenix Inverter provides the surge power needed to get things moving reliably. For those requiring even more capacity, the unit supports parallel operation of up to six devices, effectively multiplying output to reach 18kVA, or can be configured for three-phase systems.

Installation is straightforward for qualified personnel, provided safety protocols regarding grounding and ventilation are strictly followed. The unit features a programmable relay that defaults to an alarm function but can be customized via DIP switches, a VE.Net panel, or PC software. This flexibility allows users to integrate the inverter seamlessly into complex energy management systems. With robust protection against overload, low battery voltage, and high temperatures, the Phoenix Inverter ensures continuous, problem-free power delivery in diverse environments.

M: QW-35-FL

© Copyright 2026 Manual.ly