Manual.ly Logo

Telwin Superior 250 Manual

0.0 · 0 Ratings

PDF manual · 112 Pages

English

M: QW-35-FL
page

/ 112

Loading...
c208bb6fea9e448e183a1e90392bfd57809c page 8
- 8 -
Connecting the welding current return cable
This is connected to the piece being welded or to the metal bench
supporting it, as close as possible to the join being made.
This cable is connected to the terminal with the symbol (-)
Warnings:
- Turn the welding cable connectors right down into the quick
connections (if present), to ensure a perfect electrical contact;
otherwise the connectors themselves will overheat, resulting in their
rapid deterioration and loss of eciency.
- The welding cables should be as short as possible.
- Do not use metal structures which are not part of the workpiece to
substitute the return cable of the welding current: this could jeopardise
safety and result in poor welding.
6. WELDING: DESCRIPTION OF THE PROCEDURE
- It is most important that the user refers to the maker’s instructions
indicated on the stick electrode packaging. This will indicate the correct
polarity of the stick electrode and the most suitable current.
- The welding current must be regulated according to the diameter of
the electrode in use and the type of the joint to be carried out: see
below the currents corresponding to various electrode diameters:
Ø Electrode (mm)
Welding current (A)
min. max.
1.6 25 50
2 40 80
2.5 60 110
3.2 80 160
4 120 200
5 180 260
- The user must consider that, according to the electrode diameter,
higher current values must be used for at welding, whereas for vertical
or overhead welds lower current values are necessary.
- As well as being determined by the chosen current intensity, the
mechanical characteristics of the welded join are also determined by
the other welding parameters i.e. arc length, working rate and position,
electrode diameter and quality (to store the electrodes correctly, keep
them in a dry place protected by their packaging or containers).
Procedure
- Holding the mask IN FRONT OF THE FACE, strike the electrode tip on
the workpiece as if you were striking a match. This is the correct strike-
up method.
WARNING: do not hit the electrode on the workpiece, this could
damage the electrode and make strike-up dicult.
- As soon as arc is ignited, try to maintain a distance from the workpiece
equal to the diameter of the electrode in use. Keep this distance as
much constant as possible for the duration of the weld. Remember
that the angle of the electrode as it advances should be of 20-30
grades (Fig. G).
- At the end of the weld bead, bring the end of the electrode backward,
in order to ll the weld crater, quickly lift the electrode from the weld
pool to extinguish the arc.
CHARACTERISTICS OF THE WELD BEAD
Fig. H
7. MAINTENANCE
WARNING! BEFORE CARRYING OUT MAINTENANCE
OPERATIONS MAKE SURE THE WELDING MACHINE IS SWITCHED OFF
AND DISCONNECTED FROM THE MAIN POWER SUPPLY.
EXTRAORDINARY MAINTENANCE
EXTRAORDINARY MAINTENANCE MUST ONLY BE CARRIED OUT BY
TECHNICIANS WHO ARE EXPERT OR QUALIFIED IN THE ELECTRIC-
MECHANICAL FIELD, AND IN FULL RESPECT OF THE IEC/EN 60974-4
TECHNICAL DIRECTIVE.
WARNING! BEFORE REMOVING THE WELDING MACHINE
PANELS AND WORKING INSIDE THE MACHINE MAKE SURE THE
WELDING MACHINE IS SWITCHED OFF AND DISCONNECTED FROM
THE MAIN POWER SUPPLY OUTLET.
If checks are made inside the welding machine while it is live, this
may cause serious electric shock due to direct contact with live parts
and/or injury due to direct contact with moving parts.
- Inspect the welding machine regularly, with a frequency depending
on use and the dustiness of the environment, and remove the dust
deposited on the transformer, reactance and rectier using a jet of dry
compressed air (max. 10bar).
- Do not direct the jet of compressed air on the electronic boards; these
can be cleaned with a very soft brush or suitable solvents.
- At the same time make sure the electrical connections are tight and
check the wiring for damage to the insulation.
- At the end of these operations re-assemble the panels of the welding
machine and screw the fastening screws right down.
- Never, ever carry out welding operations while the welding machine is
open.
- After having carried out maintenance or repairs, restore the connections
and wiring as they were before, making sure they do not come into
contact with moving parts or parts that can reach high temperatures.
Tie all the wires as they were before, being careful to keep the high
voltage connections of the primary transformer separate from the low
voltage ones of the secondary transformer.
Use all the original washers and screws when closing the casing.
8. TROUBLESHOOTING
IN CASE OF UNSATISFACTORY FUNCTIONING, BEFORE SERVICING
MACHINE OR REQUESTING ASSISTANCE, CARRY OUT THE FOLLOWING
CHECK:
- Check that the welding current, which is regulated by the
potentiometer with a graduated amp scale, is correct for the diamter
and electrode type in use.
- Check that when general switch is ON the relative lamp is ON. If this is
not the case then the problem is located on the mains (cables, plugs,
outlets, fuses, etc.)
- Check that the yellow led (ie. thermal protection interruption- either
over or undervoltage or short circuit) is not lit.
- Check that the nominal intermittance ratio is correct. In case there is
a thermal protection interruption, wait for the machine to cool down,
check that the fan is working properly.
- Check the mains voltage: if the value is too high or too low the welding
machine will be stopped.
- Check that there is no short-circuit at the output of the machine: if this
is the case eliminate the incovenience.
- Check that all connections of the welding circuit are correct,
particularly that the work clamp is well attached to the workpiece, with
no interferring material or surface-coverings (ie. Paint).
- Protective gas must be of appropriate type (Argon 99.5%) and quantity.

Chat with your Telwin Superior 250 manual using AI

Get instant AI answers from your Telwin Superior 250 manual

Ask anything about the Telwin Superior 250. Answers come from this manual, with the pages they are based on.

Superior 250 Maintenance Schedule

Periodically
Clean internal dust with dry compressed air

Inspect the machine and remove dust from transformer, reactance and rectifier using a jet of dry compressed air (max 10 bar). Avoid directing air on electronic boards.

Periodically
Check electrical connections and insulation

Ensure all electrical connections are tight and check wiring for any damage to the insulation during inspection.

M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend Superior 250?

Yes No

Frequently Asked Questions

A

No, this machine is designed for exclusive industrial and professional use. It does not comply with electromagnetic compatibility limits for domestic environments and may interfere with household electronics.

Is this answer helpful?

A

Yes, it supports TIG welding with scratch strike using an optional TIG kit. However, Hot Start and Arc Force functions are disabled during TIG mode.

Is this answer helpful?

A

Operators must wear protective clothing compliant with UNI EN 11611, welding gloves per UNI EN 12477, and eye protection with filters meeting UNI EN 169 or 379 standards.

Is this answer helpful?

A

A yellow LED will illuminate indicating thermal protection has activated. The machine will remain off until it cools down, after which it will restart automatically.

Is this answer helpful?

A

No, individuals with metal prostheses are strictly prohibited from using this machine due to the risk of interference from electromagnetic fields generated during welding.

Is this answer helpful?

A

The duty cycle varies based on current output and ambient temperature. It is expressed as a percentage over a 10-minute cycle, ensuring safe continuous operation within thermal limits.

Is this answer helpful?

A

Use dry compressed air to remove dust from the transformer and rectifier. Avoid spraying electronic boards directly; clean them gently with a soft brush or appropriate solvent.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Inverter technology provides precise current control and excellent weld quality
  • Compact and lightweight design enhances portability and ease of handling
  • Multi-voltage capability (115V/230V) allows flexible power source usage
  • Built-in safety features like Anti-Stick and thermal protection prevent damage
  • Suitable for various electrode types including rutile, acid, and basic
VS

Disadvantages

  • Not recommended for domestic use due to electromagnetic field emissions
  • Requires qualified personnel for installation and electrical connections
  • Cannot be used by individuals with medical implants like pacemakers
  • Maintenance requires careful handling to avoid damaging electronic boards
  • Must be kept away from damp environments to prevent electrical hazards
M: QW-35-FL

Product Specification

Power

8.2kW (400V)

Open-circuit voltage

85V

Control range

10-250A (MMA/WIG)

Electrodes

0.063-0.2 inches (MMA)

Protection class

IP23

Dimensions

13.4x16.1x6.7 inches (HxWxD)

Weight

18.52 lbs

M: QW-35-FL

Product Description

Telwin Superior 250 MMA/WIG Inverter Welding Machine Review

The Telwin Superior 250 MMA/WIG Inverter Welding Machine represents a significant leap in professional welding technology, designed specifically for industrial and demanding professional environments. This robust unit utilizes advanced inverter technology to deliver precise current regulation, ensuring high-quality welds across a variety of coated electrodes including rutile, acid, and basic types. Its compact and lightweight design is a direct result of the inverter system, which drastically reduces the size of the transformer and reactance components while maintaining powerful performance.

Ideal for both MMA (Manual Metal Arc) and TIG (Tungsten Inert Gas) applications, this machine offers versatility that meets the needs of modern fabrication shops. The control panel features intuitive LED indicators that provide immediate feedback on power status, thermal protection, and voltage detection. Users can easily monitor whether the machine is operating on 115V or 230V AC power through color-coded lights, enhancing safety and operational confidence. The inclusion of Hot Start and Arc Force functions ensures smooth arc ignition and stable welding arcs, even for less experienced operators.

Safety is paramount with the Telwin Superior 250. It incorporates multiple protective systems such as anti-stick technology to prevent electrode adhesion, thermal overload protection to prevent overheating, and over/undervoltage safeguards. The machine adheres to strict European safety standards, making it suitable for use in environments with heightened electrical risks when proper precautions are taken. Operators must always wear appropriate personal protective equipment, including welding helmets with correct filters, flame-resistant clothing, and gloves, to avoid exposure to harmful UV radiation and fumes.

Installation is straightforward provided that qualified personnel handle the electrical connections. The unit requires a dedicated power supply with proper grounding and should be placed in a well-ventilated area free from conductive dust or moisture. Regular maintenance involves cleaning internal components with dry compressed air and checking cable connections to ensure optimal longevity and performance. Whether you are working on structural steel, automotive repair, or general fabrication, this welding machine delivers reliability and efficiency.

Important Safety Notes

  • Never hang the machine by its handle.
  • Do not operate near flammable materials.
  • Ensure proper ventilation to remove welding fumes.
  • Keep the machine at least 50cm away from your body during operation.
  • Persons with pacemakers or metal prostheses should not operate this equipment.
M: QW-35-FL

© Copyright 2026 Manual.ly