Manual.ly Logo

Telwin Superior 250 Manual

0.0 · 0 Ratings

PDF manual · 112 Pages

English

M: QW-35-FL
page

/ 112

Loading...
c208bb6fea9e448e183a1e90392bfd57809c page 5
- 5 -
(EN)
INSTRUCTION MANUAL
WARNING! BEFORE USING THE WELDING MACHINE READ THE
INSTRUCTION MANUAL CAREFULLY.
ARC WELDING MACHINES FOR COATED ELECTRODES (MMA) FOR
INDUSTRIAL AND PROFESSIONAL USE.
Note: In the following text the term “welding machine” will be used.
1. GENERAL SAFETY CONSIDERATIONS FOR ARC WELDING
The operator should be properly trained to use the welding machine
safely and should be informed about the risks related to arc welding
procedures, the associated protection measures and emergency
procedures.
(Please refer to the applicable standard “EN 60974-9: Arc welding
equipment. Part 9: Installation and Use).
- Avoid direct contact with the welding circuit: the no-load voltage
supplied by the welding machine can be dangerous under certain
circumstances.
- When the welding cables are being connected or checks and
repairs are carried out the welding machine should be switched o
and disconnected from the power supply outlet.
- Switch o the welding machine and disconnect it from the power
supply outlet before replacing consumable torch parts.
- Make the electrical connections and installation according to the
safety rules and legislation in force.
- The welding machine should be connected only and exclusively to
a power source with the neutral lead connected to earth.
- Make sure that the power supply plug is correctly connected to the
earth protection outlet.
- Do not use the welding machine in damp or wet places and do not
weld in the rain.
- Do not use cables with worn insulation or loose connections.
- Do not weld on containers or piping that contains or has contained
ammable liquid or gaseous products.
- Do not operate on materials cleaned with chlorinated solvents or
near such substances.
- Do not weld on containers under pressure.
- Remove all ammable materials (e.g. wood, paper, rags etc.) from
the working area.
- Provide adequate ventilation or facilities for the removal of
welding fumes near the arc; a systematic approach is needed in
evaluating the exposure limits for the welding fumes, which will
depend on their composition, concentration and the length of
exposure itself.
- Keep the gas bottle (if used) away from heat sources, including
direct sunlight.
- Use adequate electrical insulation with regard to the electrode, the
work piece and any (accessible) earthed metal parts in the vicinity.
This is normally achieved by wearing gloves, shoes, head coverings
and clothing designed for this purpose and by using insulating
platforms or mats.
- Always protect your eyes with the relative lters, which must
comply with UNI EN 169 or UNI EN 379, mounted on masks or use
helmets that comply with UNI EN 175.
Use the relative re-resistant clothing (compliant with UNI EN
11611) and welding gloves (compliant with UNI EN 12477) without
exposing the skin to the ultraviolet and infrared rays produced by
the arc; the protection must extend to other people who are near
the arc by way of screens or non-reective sheets.
- Noise: If the daily personal noise exposure (LEPd) is equal to or
higher than 85 dB(A) because of particularly intensive welding
operations, suitable personal protective means must be used (Tab.
1).
- The ow of the welding current generates electromagnetic elds
(EMF) around the welding circuit.
Electromagnetic elds can interfere with certain medical equipment
(e.g. Pace-makers, respiratory equipment, metallic prostheses etc.).
Adequate protective measures must be adopted for persons
with these types of medical apparatus. For example, they must
be forbidden access to the area in which welding machines are in
operation.
This welding machine conforms to technical product standards for
exclusive use in an industrial environment for professional purposes.
It does not assure compliance with the basic limits relative to human
exposure to electromagnetic elds in the domestic environment.
The operator must adopt the following procedures in order to reduce
exposure to electromagnetic elds:
- Fasten the two welding cables as close together as possible.
- Keep head and trunk as far away as possible from the welding
circuit.
- Never wind welding cables around the body.
- Avoid welding with the body within the welding circuit. Keep both
cables on the same side of the body.
- Connect the welding current return cable to the piece being
welded, as close as possible to the welding joint.
- Do not weld while close to, sitting on or leaning against the
welding machine (keep at least 50 cm away from it).
- Do not leave objects in ferromagnetic material in proximity of the
welding circuit.
- Minimum distance d= 20 cm (Fig. I).
- Class A equipment:
This welding machine conforms to technical product standards
for exclusive use in an industrial environment and for professional
purposes. It does not assure compliance with electromagnetic
compatibility in domestic dwellings and in premises directly
connected to a low-voltage power supply system feeding buildings
for domestic use.
EXTRA PRECAUTIONS
- WELDING OPERATIONS:
- In environments with increased risk of electric shock
- In conned spaces
- In the presence of ammable or explosive materials
MUST BE evaluated in advance by an “Expert supervisor” and must
always be carried out in the presence of other people trained to
intervene in emergencies.
All protective technical measures MUST be taken as provided in
7.10; A.8; A.10 of the applicable standard EN 60974-9: Arc welding
equipment. Part 9: Installation and Use”.
- The operator MUST NOT BE ALLOWED to weld in raised positions
unless safety platforms are used.
- VOLTAGE BETWEEN ELECTRODE HOLDERS OR TORCHES: working
with more than one welding machine on a single piece or on
pieces that are connected electrically may generate a dangerous
accumulation of no-load voltage between two dierent electrode
holders or torches, the value of which may reach double the
allowed limit.
An expert coordinator must be designated to measuring the
apparatus to determine if any risks subsist and suitable protection
measures can be adopted, as foreseen by section 7.9 of the
applicable standard “EN 60974-9: Arc welding equipment. Part 9:
Installation and Use”.
RESIDUAL RISKS
- IMPROPER USE: it is hazardous to use the welding machine for any
work other than that for which it was designed (e.g. de-icing mains
water pipes).
- Do not use the handle to hang the welding machine.
2. INTRODUCTION AND GENERAL DESCRIPTION
This welding machine is a power source for arc welding, made specically

Chat with your Telwin Superior 250 manual using AI

Get instant AI answers from your Telwin Superior 250 manual

Ask anything about the Telwin Superior 250. Answers come from this manual, with the pages they are based on.

Superior 250 Maintenance Schedule

Periodically
Clean internal dust with dry compressed air

Inspect the machine and remove dust from transformer, reactance and rectifier using a jet of dry compressed air (max 10 bar). Avoid directing air on electronic boards.

Periodically
Check electrical connections and insulation

Ensure all electrical connections are tight and check wiring for any damage to the insulation during inspection.

M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend Superior 250?

Yes No

Frequently Asked Questions

A

No, this machine is designed for exclusive industrial and professional use. It does not comply with electromagnetic compatibility limits for domestic environments and may interfere with household electronics.

Is this answer helpful?

A

Yes, it supports TIG welding with scratch strike using an optional TIG kit. However, Hot Start and Arc Force functions are disabled during TIG mode.

Is this answer helpful?

A

Operators must wear protective clothing compliant with UNI EN 11611, welding gloves per UNI EN 12477, and eye protection with filters meeting UNI EN 169 or 379 standards.

Is this answer helpful?

A

A yellow LED will illuminate indicating thermal protection has activated. The machine will remain off until it cools down, after which it will restart automatically.

Is this answer helpful?

A

No, individuals with metal prostheses are strictly prohibited from using this machine due to the risk of interference from electromagnetic fields generated during welding.

Is this answer helpful?

A

The duty cycle varies based on current output and ambient temperature. It is expressed as a percentage over a 10-minute cycle, ensuring safe continuous operation within thermal limits.

Is this answer helpful?

A

Use dry compressed air to remove dust from the transformer and rectifier. Avoid spraying electronic boards directly; clean them gently with a soft brush or appropriate solvent.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Inverter technology provides precise current control and excellent weld quality
  • Compact and lightweight design enhances portability and ease of handling
  • Multi-voltage capability (115V/230V) allows flexible power source usage
  • Built-in safety features like Anti-Stick and thermal protection prevent damage
  • Suitable for various electrode types including rutile, acid, and basic
VS

Disadvantages

  • Not recommended for domestic use due to electromagnetic field emissions
  • Requires qualified personnel for installation and electrical connections
  • Cannot be used by individuals with medical implants like pacemakers
  • Maintenance requires careful handling to avoid damaging electronic boards
  • Must be kept away from damp environments to prevent electrical hazards
M: QW-35-FL

Product Specification

Power

8.2kW (400V)

Open-circuit voltage

85V

Control range

10-250A (MMA/WIG)

Electrodes

0.063-0.2 inches (MMA)

Protection class

IP23

Dimensions

13.4x16.1x6.7 inches (HxWxD)

Weight

18.52 lbs

M: QW-35-FL

Product Description

Telwin Superior 250 MMA/WIG Inverter Welding Machine Review

The Telwin Superior 250 MMA/WIG Inverter Welding Machine represents a significant leap in professional welding technology, designed specifically for industrial and demanding professional environments. This robust unit utilizes advanced inverter technology to deliver precise current regulation, ensuring high-quality welds across a variety of coated electrodes including rutile, acid, and basic types. Its compact and lightweight design is a direct result of the inverter system, which drastically reduces the size of the transformer and reactance components while maintaining powerful performance.

Ideal for both MMA (Manual Metal Arc) and TIG (Tungsten Inert Gas) applications, this machine offers versatility that meets the needs of modern fabrication shops. The control panel features intuitive LED indicators that provide immediate feedback on power status, thermal protection, and voltage detection. Users can easily monitor whether the machine is operating on 115V or 230V AC power through color-coded lights, enhancing safety and operational confidence. The inclusion of Hot Start and Arc Force functions ensures smooth arc ignition and stable welding arcs, even for less experienced operators.

Safety is paramount with the Telwin Superior 250. It incorporates multiple protective systems such as anti-stick technology to prevent electrode adhesion, thermal overload protection to prevent overheating, and over/undervoltage safeguards. The machine adheres to strict European safety standards, making it suitable for use in environments with heightened electrical risks when proper precautions are taken. Operators must always wear appropriate personal protective equipment, including welding helmets with correct filters, flame-resistant clothing, and gloves, to avoid exposure to harmful UV radiation and fumes.

Installation is straightforward provided that qualified personnel handle the electrical connections. The unit requires a dedicated power supply with proper grounding and should be placed in a well-ventilated area free from conductive dust or moisture. Regular maintenance involves cleaning internal components with dry compressed air and checking cable connections to ensure optimal longevity and performance. Whether you are working on structural steel, automotive repair, or general fabrication, this welding machine delivers reliability and efficiency.

Important Safety Notes

  • Never hang the machine by its handle.
  • Do not operate near flammable materials.
  • Ensure proper ventilation to remove welding fumes.
  • Keep the machine at least 50cm away from your body during operation.
  • Persons with pacemakers or metal prostheses should not operate this equipment.
M: QW-35-FL

© Copyright 2026 Manual.ly