Manual.ly Logo

Telwin Alaska 150 Start Manual

0.0 · 0 Ratings

PDF manual · 76 Pages

English

M: QW-35-FL
page

/ 76

Loading...
87e8e63937293b0934033e1277d4cb37c5cc page 4
- 4 -
1. GENERAL SAFETY RULES FOR THE USE
- During the charge the battery produces explosive gases,
avoid the formation of ames and sparkes. DO NOT
SMOKE.
- Position the batteries to be charged in a well-ventilated
place.
- Inexperience and untrained people should be
properly instructed before using the appliance.
- This appliance can be used by children aged from 8
years and above and persons with reduced physical, sensory
or mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards
involved.
- Children shall not play with the appliance.
- Cleaning and user maintenance shall not be made by children
without supervision.
- Use the battery charger only indoors and make sure that you start
it in airy places. DO NOT SET IN THE RAIN OR SNOW.
- Disconnect the mains cable before connecting to or disconnecting
the charging cables from the battery.
- Do not connect or disconnect the clamps to or from the battery with
the battery charger operating.
- Never use the battery charger inside the car or in the bonnet.
- Substitute the mains cable only with an original one.
- If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualied persons in
order to avoid a hazard.
- Do not use the battery charger to charge batteries which are not
rechargeable.
- Make sure the available power supply voltage corresponds to that
shown on the battery charger rating plate.
- To prevent damaging the vehicle electronics, scrupulously respect
the warnings given by the producer of the vehicle or the batteries
used.
- This battery charger has components such as switches and relays
which can cause arcs or sparks. Therefore when using it in a
garage or in a similar place set the battery charger in a suitable
case.
- Repair or maintenance of the inside of the battery charger can be
executed only by skilled technicians.
- WARNING: ALWAYS DISCONNECT THE POWER SUPPLY
CABLE FROM THE MAINS BEFORE CARRYING OUT ANY
SIMPLE MAINTENANCE OPERATION ON THE BATTERY
CHARGER.
- The battery charger is protected from indirect contact by an earth
wire as indicated for class I equipment. Make sure the power outlet
is protected by an earth connection.
- For models supplied without plugs, connect plugs having a
capacitance suitable for the value of the fuse shown in the plate;
for models supplied with cable and plug and with a ”P.MAX
START” power higher than 9kW, when used for starting, we advise
replacing the plug with one having a capacitance suitable for the
fuse shown in the plate.
2. GENERAL DESCRIPTION
2.1 AUTOMATIC BATTERY CHARGERS (TRONIC)
Automatic battery chargers (electronic control of the charge process,
interruption and automatic restart) designed for charging sealed
batteries (GEL AGM) in TRONIC mode, and lead electrolyte free
batteries (WET) in manual CHARGE mode, used on motor vehicles
(petrol and diesel), motorcycles, boats etc. It is possible to recharge
12V and 24V batteries.
Rechargeable batteries according to the output voltage available: 6V
/ 3 cells; 12V / 6 cells; 24V / 12 cells.
3. CONTROL, ADJUSTMENT AND INDICATOR DEVICES
3.1 CHARGE LEVEL INDICATOR (AMMETER FIG. A)
During the charge phase, the charge level indicator moves from right
to left indicating a decrease in the current required by the battery
as far as near zero levels (battery charged). Please note that the
exact battery status can only be determined using a hydrometer,
that allows you to measure the specic density of the electrolyte. For
battery chargers in manual CHARGE mode, it will be necessary to
monitor the ammeter to determine when the battery is fully charged
and needs to be disconnected from the battery charger to prevent
overheating or damage to the same. In START mode, the indicator
will move to the far right indicating the use of maximum current.
3.2 SETTING THE CHARGE MODE AND CHARGE CURRENT
(FIG. B)
The switch seen in gure B-1 is used to select the TRONIC or
CHARGE mode settings.
The current and charge voltage (where available) is increased by
moving the switch cursor seen in gure B-2 from left to right, within
the CHARGE/TRONIC range.
Move the cursor seen in gure B-2 to the far right to reach the START
position to help start the vehicle.
3.3 INDICATOR LEDS (FIG. C)
The LED seen in gure C-1 indicates that the charge clamps are
connected to the battery with the poles inverted.
WARNING! Although the battery charger is protected by a resettable
fuse, always avoid creating sparks connecting the clamps with the
poles inverted! Disconnect the clamps immediately and connect
them to the battery correctly.
The two-tone LED seen in gure C-2 is always red in CHARGE mode
and indicates that the battery is charging. In TRONIC mode, the LED
turns green when the charge phase is completed.
4. INSTALLATION
4.1 POSITIONING THE BATTERY CHARGER
During operation, position the battery charger on a stable surface
and make sure that there is no obstruction to air passage through the
openings provided to ensure sufcient ventilation.
4.2 CONNECTION TO THE MAIN SUPPLY
- The battery charger should be connected only and exclusively
to a power source with the neutral lead connected to earth.
Check that the mains voltage is the same as the voltage of the
equipment.
- Check that the power supply is protected by systems such as
fuses or automatic switches, sufcient to support the maximum
absorption of the equipment.
- The connection to the main supply has to be made using a suitable
cable.
- If you put an extension to the primary cable, the section should
be adequate and, in any case, never less than that of the cable
supplied.
- You always have to earth the equipment with the yellow/green wire
contained in the main cable, indicated by the label (W), while the
other two wires should be connected to the phase and the neutral
1. GENERAL SAFETY RULES FOR THE USE........................................... 4
2. GENERAL DESCRIPTION ...................................................................... 4
2.1 AUTOMATIC BATTERY CHARGERS (TRONIC) .............................. 4
3. CONTROL, ADJUSTMENT AND INDICATOR DEVICES ....................... 4
3.1 CHARGE LEVEL INDICATOR (AMMETER FIG. A) .......................... 4
3.2 SETTING THE CHARGE MODE AND CHARGE
CURRENT (FIG. B) ........................................................................... 4
3.3 INDICATOR LEDS (FIG. C) ............................................................... 4
4. INSTALLATION ........................................................................................ 4
4.1 POSITIONING THE BATTERY CHARGER ....................................... 4
4.2 CONNECTION TO THE MAIN SUPPLY ............................................ 4
5. OPERATION DURING CHARGING ......................................................... 5
5.1 BATTERY PREPARATION ................................................................ 5
5.2 BATTERY CHARGER/BATTERY CONNECTION ............................. 5
5.3 MANUAL CHARGE AND AUTOMATIC CHARGE MODES ............... 5
5.3.1 MANUAL CHARGE (CHARGE) MODE ................................... 5
5.3.2 AUTOMATIC CHARGE (TRONIC) MODE .............................. 5
5.4 SIMULTANEOUS CHARGING OF MULTIPLE BATTERIES.............. 5
5.5 CHARGE ENDING ............................................................................ 5
6. VEHICLE STARTING OPERATION ......................................................... 5
6.1 BATTERY CHARGER/BATTERY CONNECTION ............................. 5
6.2 STARTING WITH START .................................................................. 5
6.3 END OF STARTING .......................................................................... 5
7. BATTERY CHARGER PROTECTION ..................................................... 5
8. USEFUL ADVICE ..................................................................................... 5
INDEX
ENGLISH

Chat with your Telwin Alaska 150 Start manual using AI

Get instant AI answers from your Telwin Alaska 150 Start manual

Ask anything about the Telwin Alaska 150 Start. Answers come from this manual, with the pages they are based on.

Alaska 150 Start Maintenance Schedule

Before each charge
Check electrolyte level and add distilled water if needed

For WET batteries, ensure electrolyte covers plates. If not, add distilled water to cover by 5-10 mm. Use extreme caution as electrolyte is corrosive.

As needed
Clean battery terminals of oxide

If positive and negative terminals are incrusted with oxide, clean them to ensure good contact with the clamps.

M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend Alaska 150 Start?

Yes No

Frequently Asked Questions

A

Yes, the device is suitable for motorcycles, cars, and boats, supporting 12V and 24V systems depending on the model configuration.

Is this answer helpful?

A

TRONIC is automatic for sealed batteries like GEL and AGM, while CHARGE is manual for wet lead-acid batteries requiring user monitoring.

Is this answer helpful?

A

In TRONIC mode, the LED turns green. In CHARGE mode, watch the ammeter drop near zero or check for liquid boiling in wet batteries.

Is this answer helpful?

A

Yes, provided they have compatible voltages and capacities, connected either in series or parallel according to specific guidelines.

Is this answer helpful?

A

Yes, using the START function, but you must follow the recommended work-pause cycles to prevent overheating the charger.

Is this answer helpful?

A

Disconnect immediately. The device has protection, but sparks may occur. Reconnect correctly to avoid damage.

Is this answer helpful?

A

Store it in a dry place away from moisture and direct sunlight to ensure longevity and safety.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Supports both automatic TRONIC mode for sealed batteries and manual CHARGE mode for wet batteries
  • Includes a dedicated START function for high-current engine assistance
  • Features comprehensive protection against reverse polarity, short circuits, and overcharge
  • Compatible with 6V, 12V, and 24V battery systems for diverse vehicle types
  • Clear indicator LEDs and an ammeter provide real-time status feedback during operation
VS

Disadvantages

  • Requires strict adherence to ventilation rules due to explosive gas risks during charging
  • Cannot be used inside a vehicle or under the bonnet due to spark hazards
  • Multiple battery charging requires careful configuration of series or parallel setups
  • Fuse replacement must strictly match rated values to avoid equipment damage
  • Initial setup requires reading the manual carefully to understand voltage selection switches
M: QW-35-FL

Product Specification

Suitable for

AGM, Lead, Gel

Battery voltage

12V

Max charging current

12A

Battery capacity

10-200Ah

Display

Analog pointer

Features

Jump start

Color

black, white

Dimensions

9.65x7.68x5.12 in (WxDxH)

Weight

13.01 lbs

M: QW-35-FL

Product Description

Telwin Alaska 150 Start Manual: Your Ultimate Guide to Reliable Power

The Telwin Alaska 150 Start Manual serves as the essential companion for owners of this versatile battery charger and starter. This device is designed to handle a wide range of vehicles, including cars, motorcycles, and boats, ensuring that your power source remains robust and ready for action. Whether you are dealing with sealed GEL or AGM batteries using the advanced TRONIC mode, or traditional wet lead-acid batteries requiring manual CHARGE settings, this unit adapts to your needs with precision.

Understanding the operation of the Telwin Alaska 150 Start is crucial for safety and efficiency. The manual guides users through the critical steps of connecting clamps, selecting the correct voltage for 6V, 12V, or 24V systems, and monitoring the charge level via the integrated ammeter. It highlights the importance of working in well-ventilated areas to avoid explosive gases and emphasizes strict adherence to polarity rules to prevent sparks or damage to vehicle electronics. The START function offers a powerful boost for difficult engine starts, but it requires careful attention to work-pause cycles to prevent overheating.

Beyond basic charging, the guide explains how to safely charge multiple batteries simultaneously using series or parallel connections. It also details the protective features built into the charger, such as safeguards against overcharging, short circuits, and reversed polarity. By following these instructions, users can extend the life of their batteries and ensure the longevity of the charger itself. Proper maintenance, including cleaning terminals and storing the unit in a dry place, is emphasized throughout the text to maintain optimal performance.

Important Safety Notes

Always disconnect the mains cable before connecting or disconnecting clamps. Never operate the device in rain or snow. Ensure the fuse rating matches the plate specifications exactly. Do not attempt to repair internal components yourself; only qualified technicians should handle internal repairs.

Pros and Cons

Pros

  1. Supports both automatic TRONIC mode for sealed batteries and manual CHARGE mode for wet batteries.
  2. Includes a dedicated START function for high-current engine assistance.
  3. Features comprehensive protection against reverse polarity, short circuits, and overcharge.
  4. Compatible with 6V, 12V, and 24V battery systems for diverse vehicle types.
  5. Clear indicator LEDs and an ammeter provide real-time status feedback during operation.

Cons

  1. Requires strict adherence to ventilation rules due to explosive gas risks during charging.
  2. Cannot be used inside a vehicle or under the bonnet due to spark hazards.
  3. Multiple battery charging requires careful configuration of series or parallel setups.
  4. Fuse replacement must strictly match rated values to avoid equipment damage.
  5. Initial setup requires reading the manual carefully to understand voltage selection switches.

Frequently Asked Questions

Can I use the Telwin Alaska 150 Start on a motorcycle? Yes, the device is suitable for motorcycles, cars, and boats, supporting 12V and 24V systems depending on the model configuration.

What is the difference between TRONIC and CHARGE modes? TRONIC is automatic for sealed batteries like GEL and AGM, while CHARGE is manual for wet lead-acid batteries requiring user monitoring.

How do I know when the battery is fully charged? In TRONIC mode, the LED turns green. In CHARGE mode, watch the ammeter drop near zero or check for liquid boiling in wet batteries.

Can I charge two batteries at the same time? Yes, provided they have compatible voltages and capacities, connected either in series or parallel according to specific guidelines.

Is it safe to start a car with this device? Yes, using the START function, but you must follow the recommended work-pause cycles to prevent overheating the charger.

What should I do if the polarity is reversed? Disconnect immediately. The device has protection, but sparks may occur. Reconnect correctly to avoid damage.

Where should I store the charger after use? Store it in a dry place away from moisture and direct sunlight to ensure longevity and safety.

M: QW-35-FL

© Copyright 2026 Manual.ly