Manual.ly Logo

Tamiya Subaru BRZ R&D Sport 2014 TT-02 Manual

0.0 · 0 Ratings

PDF manual · 24 Pages

English

M: OA-GPT-54-NAN
page

/ 24

Loading...
f0ac2f93d2ae73cffa9ba7802e5368e2f685 page 14
20
SAFETY PRECAUTIONS
Follow the outlined rules for safe radio control
operation.
●
Avoid running the car in crowded areas and near
small children.
●
Make sure that no one else is using the same
frequency in your running area. Using the same
frequency at the same time can cause serious
accidents, whether it’s driving, flying, or sailing.
●
Avoid running in standing water and rain. If R/C
unit, motor, or battery get wet, clean and dry
thoroughly in a dry shaded area.
R/C OPERATING PROCEDURES
①
Switch on transmitter. If using a transmitter with
an extending antenna, fully extend.
②
Switch on receiver.
③
Inspect operation using transmitter before
running.
④
Adjust steering servo and trim so that the model
runs straight with transmitter in neutral.
⑤
Reverse sequence to shut down after running.
⑥
Make sure to disconnect/remove all batteries.
⑦
Completely remove sand, mud, dirt etc.
⑧
Apply grease to suspension, gears, bearings, etc.
⑨
Store the car and batteries separately when not
in use.
TIPS ZUR SICHERHEIT
Beachten Sie die folgenden Richtlinien für
fehlerfreien Betrieb.
●
Vermeiden Sie das Fahren des Autos an
überfüllten Plätzen und in der Nähe von kleinen
Kindern. Gebrauchen Sie nie die Straße für R/C
Rennen.
●
Prüfen Sie, daß niemand in der Umgebung
dieselbe Frequenz benutzt, denn dadurch können
Unfälle entstehen - sowohl beim Fahren, Fliegen
oder Segeln.
●
Vermeiden Sie das Fahren durch Pfützen und
während Regen. Wenn das R/C Fahrzeug, der
Motor oder die Batterien naß werden, müssen Sie
alles sorgfältig im Trockenen säubern und
reinigen.
KONTROLLEN VOR DER FAHRT
①
Sender einschalten. Wenn Sie einen Sender mit
Teleskopantenne benutzen, dieses ganz ausziehen.
②
Empfänger einschalten.
③
Die Funktion vor Abfahrt mit dem Sender
überprüfen.
④
Richten Sie das Lenkservo durch Einstellung am
Gestänge so ein, daß das Modell bei neutraler
Sender-Trimmung geradeaus fährt.
⑤
Nach dem Fahrbetrieb in umgekehrter Reihen-
folge vorgehen.
⑥
Die Batterien herausnehmen bzw. abklemmen.
⑦
Entfernen Sie Sand, Matsch, Schmutz etc.
⑧
Fetten Sie die Aufhängung, Getriebe, Federun-
gen etc. ein.
⑨
Bei Nichtgebrauch Auto und Akkus getrennt
verwahren.
MESURES DE SECURITE
Veuillez respecter impérativement les règles de
sécurité suivantes lors de l’utilisation de votre
ensemble R/C.
●
Eviter de faire évoluer la voiture à proximité de
jeunes enfants ou dans la foule. Ne jamais utiliser
sur la voie publique!
●
Assurez-vous que personne d’autre n’utilise la
même fréquence sur le même terrain que vous.
Utiliser la même fréquence en même temps peut
être source de sérieux accidents, pendant la
conduite, le vol ou la navigation des modèles R/C.
●
Ne jamais faire évoluer le modèle sous la pluie
ou sur une surface mouillée. Si le moteur, les
accus, le récepteur ou les servos prenaient
l’humidité, les nettoyer avec un chiffon et les
laisser sécher.
PROCEDURE DE MISE EN MARCHE
①
Allumer l’émetteur. Déployer entièrement
l’antenne de l’émetteur, s’il en est doté.
②
Mettre en marche le récepteur.
③
Vérifiez la bonne marche de votre radiocom-
mande avant de rouler.
④
Le trim de direction doit être réglé pour que
manche au neutre, le modèle évolue en ligne
droite.
⑤
Faites les opérations inverses après utilisation
de votre ensemble R/C.
⑥
Assurez-vous que les batteries soient bien
débranchées et sortez-les du modèle.
⑦
Enlever sable, poussière, boue etc...
⑧
Graisser les pignons, articulations...
⑨
Rangez la voiture et les accus séparément.
スイッチをONにします。アンテナ付き送信機の
場合はアンテナをのばしてください。
走らせる前にRCカーを台の上に乗せ、各部の動
きをチェックします。
次にRCカー側のスイッチをONにしてください。
ステアリングを使わず走らせてみます。まっすぐ
に走らない場合はステアリングトリムを使って調
節してください。
走行を終わらせる時は、かならず走らせる時の逆の手順でスイッチを切っていきます。
走らせたあとは、かならずバッテリーをはずして
おきましょう。
RCカーについた泥や砂、汚れなどはやわらかな
布などできれいに拭き取りましょう。
あとかたづけをしっかりしましょう。その時、バッ
テリーは別々にしておきます。
ギヤや軸受け部、サスペンションなどの可動部は
グリスをさしておきましょう。
★この走らせかたの順番はかならず守ってください。スイッチ
のON/OFFの順番を間違えると他の電波の混信によってRC
カーが暴走する場合があります。
《RCカーの走らせかた》
●走らせない時はバッテリーを
必ずはずしておきましょう。
RCC TT-02 Chassis
(
11053610
)

Chat with your Tamiya Subaru BRZ R&D Sport 2014 TT-02 manual using AI

Get instant AI answers from your Tamiya Subaru BRZ R&D Sport 2014 TT-02 manual

Ask anything about the Tamiya Subaru BRZ R&D Sport 2014 TT-02. Answers come from this manual, with the pages they are based on.

Subaru BRZ R&D Sport 2014 TT-02 Maintenance Schedule

After every run
Clean and dry R/C unit, motor, and battery

Completely remove sand, mud, dirt etc. If wet, clean and dry thoroughly in a dry shaded area.

Show in the manual (page 20)
After every run
Apply grease to suspension, gears, and bearings

Apply grease to moving parts such as suspension, gears, and bearings after running.

Show in the manual (page 20)
Before operation
Check antenna extension

Fully extend the transmitter and receiver antennas before operating the car.

Show in the manual (page 20)
M: QW-35-FL

Ask a Question

0/1000

Do you recommend Subaru BRZ R&D Sport 2014 TT-02?

Yes No

Frequently Asked Questions

A

It explains how to build and set up an on-road RC car based on Tamiya’s TT-02 chassis and the Subaru BRZ R&D Sport 2014 body. It covers assembly, electronics, tuning, and safe operation.

Is this answer helpful?

A

Yes, but beginners may need help. The manual includes detailed steps, yet some parts require careful assembly, tools, and basic RC knowledge. A supervising adult or experienced hobbyist can be useful.

Is this answer helpful?

A

You need a standard 2-channel radio system, an electronic speed controller, a standard-size servo, and a compatible battery pack with charger. These items are not included in the kit.

Is this answer helpful?

A

Yes. The TT-02 layout allows changes to wheelbase, tread, and ground clearance so it can better match different body requirements and driving preferences.

Is this answer helpful?

A

No. It is intended for on-road use only. Gravel, sand, and wet conditions can affect gears, suspension parts, and electronics.

Is this answer helpful?

A

Ball bearings are a popular upgrade for smoother running. You can also change pinion gears, adjust gearing, or add optional parts to improve performance and durability.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • Adjustable TT-02 chassis supports different body setups and tuning options.
  • Clear assembly guidance makes it useful for learning RC mechanics.
  • On-road suspension and drivetrain are built for stable, responsive handling.
  • Upgrade paths like bearings and pinion gears add long-term value.
VS

Disadvantages

  • Not suited for off-road use; debris can interfere with moving parts.
  • Requires extra electronics and battery gear that are not included.
  • Small parts and precise assembly may be challenging for beginners.
  • Performance depends heavily on correct setup and maintenance.
M: OA-GPT-54-NAN

Product Specification

Type

Car

Scale

1:10

Drive

Electric motor

M: OA-GPT-54-NAN

Product Description

Tamiya Subaru BRZ R&D Sport 2014 TT-02 Manual

The Tamiya Subaru BRZ R&D Sport 2014 TT-02 Manual introduces a sharp, race-inspired on-road RC build centered on Tamiya’s trusted TT-02 chassis. Designed around the Subaru BRZ R&D Sport 2014 body style, this kit blends realistic styling with a durable platform that is ideal for hobbyists who enjoy assembling, tuning, and learning how an RC car comes together from the ground up.

At the core of the model is the TT-02 chassis, a versatile layout that supports smooth handling and a wide range of setup options. Builders can adjust the wheelbase, ride height, and tread to match the body configuration, making the chassis more adaptable than many entry-level kits. The manual also shows how gearing changes can influence performance, giving users a practical way to experiment with acceleration and speed.

The build emphasizes careful assembly and correct part selection. It includes guidance for suspension, differential gears, steering linkage, dampers, wheels, and motor installation, while reminding users to use standard-size servos and a compatible 2-channel radio system with ESC. The instructions also highlight lubrication points, antenna placement, and battery handling, all of which help the finished car perform reliably on smooth surfaces.

What makes this model appealing is its balance of simplicity and upgrade potential. The kit comes with enough detail to teach RC fundamentals, yet it still leaves room for future improvements such as ball bearings, different pinion gears, and optional parts. That makes it a strong choice for both newcomers and experienced builders who want a solid base for an on-road touring car.

The Subaru BRZ body adds a sporty, modern look that matches the chassis’ performance-minded character. Once assembled, the result is an RC car that feels precise, customizable, and rewarding to drive. It is best suited to clean pavement and controlled environments, where its suspension and steering can shine.

Notes

  • On-road use only; dirt and gravel can damage moving parts.
  • Use the correct servo size and a compatible ESC.
  • Follow the setup guide for wheelbase, tread, and ride height.
  • Battery and transmitter order matters for safe operation.
  • Regular cleaning and greasing help maintain performance.
M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly