Manual.ly Logo

Shelly Plus H&T Manual

0.0 · 0 Ratings

PDF manual · 2 Pages

English

M: QW-35-FL
page

/ 2

Loading...
b550bb28a3ab7f12a419b0074aaf5329da8f page 1
EN
USER AND SAFETY GUIDE
WI-FI HUMIDITY AND TEMPERATURE SENSOR
Read before use
This document contains important technical and safety information about the
device, its safety use and installation.
⚠CAUTION! Before beginning the installation, please read this guide and any other
documents accompanying the device carefully and completely. Failure to follow the
installation procedures could lead to malfunction, danger to your health and life,
violation of the law or refusal of legal and/or commercial guarantee (if any). Allterco
Robotics EOOD is not responsible for any loss or damage in case of incorrect instal-
lation or improper operation of this device due to failure of following the user and
safety instructions in this guide.
Product Introduction
Shelly® is a line of innovative microprocessor-managed devices, which allow re-
mote control of electric circuits through a mobile phone, tablet, PC, or home auto-
mation system. Shelly® devices can work standalone in a local Wi-Fi network or
they can also be operated through cloud home automation services. Shelly Cloud
is a service that can be accessed using either Android or iOS mobile application,
or with any internet browser at https://home.shelly.cloud/. Shelly® devices can
be accessed, controlled and monitored remotely from any place where the User
has internet connectivity, as long as the devices are connected to a Wi-Fi router
and the Internet. Shelly® devices have embedded Web Interface accessible at
http://192.168.33.1 when connected directly to the device access point, or at the
device IP address on the local Wi-Fi network. The embedded Web Interface can be
used to monitor and control the device, as well as adjust its settings.
Shelly® devices can communicate directly with other Wi-Fi devices through HTTP
protocol. An API is provided by Allterco Robotics EOOD. For more information,
please visit: https://shelly-api-docs.shelly.cloud/#shelly-family-overview.
Shelly® devices are delivered with factory-installed rmware. If rmware updates
are necessary to keep the devices in conformity, including security updates, Allter-
co Robotics EOOD will provide the updates free of charge through the device em-
bedded Web Interface or Shelly Mobile Application, where the information about
the current rmware version is available. The choice to install or not the device
rmware updates is user’s sole responsibility. Allterco Robotics EOOD shall not be
liable for any lack of conformity of the device caused by failure of the user to install
the provided updates in a timely manner.
Shelly Plus H&T (the Device) is a Wi-Fi smart humidity and temperature sensor.
Installation instruction
⚠CAUTION! Do not use the Device if it has been damaged.
⚠CAUTION! Do not attempt to service or repair the Device yourself.
1. Power supply
Shelly Plus H&T can be powered by 4 AA (LR6) 1.5 V batteries or a USB Type-C
power supply adapter.
⚠CAUTION! Use the Device only with batteries or USB Type-C power supply adapt-
ers that comply with all applicable regulations. Inappropriate batteries or power
supply adapters may damage the Device and cause re.
A. Batteries
Remove the Device back cover using a at screwdriver as shown on g. 1, insert
the bottom row batteries as shown on g. 3 and the top row batteries as shown
on g. 4.
⚠CAUTION! Make sure the batteries + and - signs correspond to marking on the
Device battery compartment (g. 2 A)
B. USB Type-C power supply adapter
Insert the USB Type-C power supply adapter cable into the Device USB Type-C port
(g. 2 C)
⚠CAUTION! Do not connect the adapter to the Device if the adapter or the cable
are damaged.
⚠CAUTION! Unplug the USB cable before removing or placing the back cover.
⚠IMPORTANT: The Device cannot be used to charge rechargeable batteries.
2. Starting
When initially powered the Device will be put in Setup mode and the display will
show SEt instead of the temperature. By default the Device access point is enabled,
which is indicated by AP in the bottom right corner of the display. If it is not enabled,
press and hold the Reset button (g. 2 B) for 5 seconds to enable it.
⚠IMPORTANT: To save the batteries the Device stays in Setup mode for 3 minutes
and then goes to Sleep mode and the display will show the measured temperature.
Press briey the Reset button to bring it back to Setup mode. Pressing briey the
Reset button while the Device is in Setup mode will put the Device to Sleep mode.
3. Inclusion to Shelly Cloud
If you choose to use the Device with the Shelly Cloud mobile application and Shelly
Cloud service, instructions on how to connect the Device to the Cloud and control it
through the Shelly App can be found in the “App Guide”.
The Shelly Mobile Application and Shelly Cloud service are not conditions for the
Device to function properly. This Device can be used stand-alone or with various
other home automation platforms and protocols.
⚠CAUTION! Do not allow children to play with the buttons/switches connected to
the Device. Keep the Devices for remote control of Shelly (mobile phones, tablets,
PCs) away from children.
4. Manually connecting to a local Wi-Fi network
Shelly Plus H&T can be managed and controlled through its embedded web inter-
face. Make sure the Device is in Setup mode, its access point is enabled and you are
connected to it using a Wi-Fi enabled device. From a web browser open the Device
Web Interface by navigating to 192.168.33.1. Click the Networks button and then
expand the Wi section.
Enable the Wi1 and/or Wi2 (backup network) by toggling the corresponding
Enable switch. Enter the Wi-Fi network name(s) (SSID) or select it(them) by clicking
on the gray Click here to select network link(s). Enter the Wi-Fi network password(s)
and click APPLY.
The Device URL will appear in blue color at the top of the Wi section, when the
device is successfully connected to the Wi-Fi network.
⚠RECOMMENDATION: For security reasons we recommend disabling the AP
mode, after the Device successful connection to the local Wi-Fi network. Expand the
Access point section and toggle the Enable switch.
When ready including the Device to Shelly Cloud or another service, place the back
cover.
DE
BEDIENUNGS- UND SICHERHEITSHANDBUCH
WI-FI-LUFTFEUCHTIGKEITS- UND
TEMPERATURSENSOR
Bitte vor Gebrauch durchlesen
Dieses Dokument enthält wichtige technische und sicherheitstechnische Infor-
mationen über das Gerät und seine sichere Verwendung und Installation.
⚠ACHTUNG! Bevor Sie mit der Installation beginnen, lesen Sie bitte die Begleitdo-
kumentation sorgfältig und vollständig durch. Die Nichtbeachtung der empfohlenen
Verfahren kann zu Fehlfunktionen, Lebensgefahr oder Gesetzesverstößen führen.
Allterco Robotics EOOD haftet nicht für Verluste oder Schäden im Falle einer fal-
schen Installation oder Bedienung dieses Geräts.
Produktvorstellung
Shelly® ist eine Produktserie innovativer, mikroprozessorgesteuerter Geräte, wel-
che die Fernsteuerung von Elektrogeräten über ein Mobiltelefon, ein Tablet, einen
PC oder ein Hausautomatisierungssystem ermöglichen. Shelly® Geräte können
eigenständig in einem lokalen WLAN-Netzwerk arbeiten oder sie können auch über
Cloud-Dienste für die Hausautomatisierung betrieben werden. Shelly Cloud ist ein
solcher Dienst, auf den entweder über eine Android- oder iOS-Applikation oder über
einen beliebigen Internetbrowser unter https://home.shelly.cloud/ zugegriffen
werden kann. Shelly® Geräte können von jedem Ort aus, an dem der Benutzer eine
Internetverbindung hat, angesprochen, gesteuert und überwacht werden, solange
die Geräte mit einem WLAN-Router und dem Internet verbunden sind. Shelly® Ge-
räte verfügen über eine integrierte Web-Schnittstelle, die unter http://192.168.33.1
im WLAN-Netzwerk zugänglich ist, das vom Gerät im Access Point-Modus erstellt
wird, oder unter der IP-Adresse des Gerätes im WLAN-Netzwerk, mit dem es ver-
bunden ist. Díe integrierte Web-Schnittstelle kann zur Überwachung und Steuerung
des Gerätes sowie zur Anpassung dessen Einstellungen verwendet werden.
Shelly® Geräte können direkt mit anderen WLAN-Geräten über das HTTP-Protokoll
kommunizieren. Eine API wird von Allterco Robotics EOOD bereitgestellt. Für wei-
tere Informationen besuchen Sie bitte:
https://shelly-api-docs.shelly.cloud/#shelly-family-overview.
Shelly® Geräte werden mit werkseitig installierter Firmware ausgeliefert. Um die
Geräte konform zu halten, stellt Allterco Robotics EOOD die notwendigen Firm-
ware-Updates, einschließlich der Sicherheitsupdates, kostenlos über die im Gerät
eingebettete Web-Schnittstelle sowie über die Shelly-App zur Verfügung. Die Ent-
scheidung, die Firmware-Updates des Geräts zu installieren oder nicht, obliegt der
alleinigen Verantwortung des Benutzers. Allterco Robotics EOOD haftet nicht für
Konformitätsmängel des Geräts, die darauf zurückzuführen sind, dass der Benut-
zer die bereitgestellten Updates nicht rechtzeitig installiert hat.
Shelly Plus H&T (das Gerät) ist ein intelligenter Wi-Fi-Luftfeuchtigkeits- und Tem-
peratursensor.
Installationsanleitung
⚠VORSICHT! Verwenden Sie das Gerät nicht, wenn es beschädigt ist.
⚠VORSICHT! Versuchen Sie nicht, das Gerät selbst zu warten oder zu reparieren.
1. Stromzufuhr
Shelly Plus H&T kann mit 4 Batterien des Typs AA (LR6) 1,5 V oder einem USB-Typ-
C-Netzteil betrieben werden.
⚠VORSICHT! Verwenden Sie das Gerät nur mit Batterien oder USB-Typ-C-Netzteil-
adaptern, die allen geltenden Vorschriften entsprechen. Ungeeignete Batterien oder
Netzteile können das Gerät beschädigen und einen Brand verursachen.
A. Batterien
Entfernen Sie die Abdeckung der Geräterückseite mit einem achen Schrauben-
zieher (siehe Abb. 1), legen Sie die Batterien der unteren Reihe (siehe Abb. 3) und
die Batterien der oberen Reihe (siehe Abb. 4) ein.
⚠VORSICHT! Achten Sie darauf, dass die + und - Zeichen der Batterien mit den
Markierungen auf dem Batteriefach des Geräts übereinstimmen (Abb. 2 A).
B. USB-Typ-C-Netzteiladapter
Stecken Sie das Kabel des USB-Typ-C-Netzteiladapters in den USB-Typ-C-An-
schluss des Geräts (Abb. 2 C).
⚠VORSICHT! Schließen Sie den Adapter nicht an das Gerät an, wenn der Adapter
oder das Kabel beschädigt sind.
⚠VORSICHT! Ziehen Sie das USB-Kabel ab, bevor Sie die hintere Abdeckung ent-
fernen oder anbringen.
⚠WICHTIG: Das Gerät kann nicht zum Auaden von wiederauadbaren Batterien
verwendet werden.
2. Einschalten
Beim ersten Einschalten bendet sich das Gerät im Setup-Modus, und auf dem Dis-
play wird SEt anstelle der Temperatur angezeigt. Standardmäßig ist der Zugangs-
punkt des Geräts aktiviert, was durch AP in der unteren rechten Ecke des Displays
angezeigt wird. Wenn er nicht aktiviert ist, halten Sie die Reset-Taste (Abb. 2 B) 5
Sekunden lang gedrückt, um ihn zu aktivieren.
⚠WICHTIG: Um die Batterien zu schonen, bleibt das Gerät 3 Minuten lang im Ein-
stellungsmodus und geht dann in den Ruhemodus über, wobei das Display die ge-
messene Temperatur anzeigt. Drücken Sie kurz die Reset-Taste, um das Gerät wie-
der in den Setup-Modus zu bringen. Durch kurzes Drücken der Reset-Taste, während
sich das Gerät im Setup-Modus bendet, wird das Gerät in den Ruhemodus versetzt.
3. Einbindung in Shelly Cloud
Wenn Sie sich dafür entscheiden, das Gerät mit der Shelly Cloud App und dem
Shelly Cloud Service zu verwenden, nden Sie Anweisungen zur Verbindung des
Geräts mit der Cloud und zur Steuerung über die Shelly App im “App Guide”. Die
Shelly Mobile App und der Shelly Cloud Service sind keine Voraussetzung für das
ordnungsgemäße Funktionieren des Geräts. Dieses Gerät kann alleine, sowie mit
verschiedenen anderen Hausautomatisierungsdiensten und -anwendungen ver-
wendet werden.
⚠VORSICHT! Erlauben Sie Kindern nicht, mit den an das Gerät angeschlossenen
Tasten/Schaltern zu spielen. Halten Sie die Geräte zur Fernsteuerung des Shelly
(z.B.: Mobiltelefone, Tablets, PCs) von Kindern fern.
4. Manuelle Verbindung mit einem lokalen Wi-Fi-Netzwerk
Shelly Plus H&T kann über seine integrierte Webschnittstelle verwaltet und gesteu-
ert werden. Vergewissern Sie sich, dass sich das Gerät im Setup-Modus bendet,
sein Zugangspunkt aktiviert ist und Sie über ein Wi-Fi-fähiges Gerät mit dem Gerät
verbunden sind. Öffnen Sie in einem Webbrowser die Webschnittstelle des Geräts,
indem Sie zu 192.168.33.1 navigieren. Klicken Sie auf die Schaltäche Networks
(Netzwerke) und erweitern Sie dann den Abschnitt Wi.
Aktivieren Sie Wi1 und/oder Wi2 (Backup-Netzwerk), indem Sie den entspre-
chenden Aktivierungsschalter umlegen. Geben Sie den/die Namen des Wi-Fi-Netz-
werks (SSID) ein oder wählen Sie es/sie aus, indem Sie auf den grauen Link Click
here to select network(s) klicken. Geben Sie das/die Passwort(e) für das Wi-Fi-
Netzwerk ein und klicken Sie auf ANWENDEN.
Die Geräte-URL erscheint in blauer Farbe am oberen Rand des Wi-Bereichs, wenn
das Gerät erfolgreich mit dem Wi-Fi-Netzwerk verbunden ist.
⚠EMPFEHLUNG: Aus Sicherheitsgründen empfehlen wir, den AP-Modus zu deak-
IT
GUIDA ALL’USO E ALLA SICUREZZA
SENSORE DI UMIDITÀ E TEMPERATURA WI-FI
Leggere prima dell’uso
Questo documento contiene importanti informazioni tecniche e di sicurezza sul
dispositivo e sul suo uso e installazione in sicurezza.
⚠ATTENZIONE! Prima di iniziare l’installazione leggere attentamente e comple-
tamente la documentazione allegata. La mancata osservanza delle procedure con-
sigliate potrebbe portare a malfunzionamenti, pericolo per la vita o violazione della
legge. Allterco Robotics EOOD non è responsabile per eventuali perdite o danni in
caso di installazione o funzionamento errati di questo dispositivo.
Introduzione al prodotto
Shelly® è una linea di dispositivi innovativi gestiti da microprocessori che permet-
tono il controllo remoto degli elettrodomestici attraverso un telefono cellulare, un
tablet, un PC o un sistema domotico. I dispositivi Shelly® sono in grado di fun-
zionare autonomamente in una rete Wi-Fi locale o possono anche essere gestiti
attraverso servizi di automazione domestica cloud. Shelly Cloud è un servizio di
questo tipo a cui si può accedere utilizzando un’applicazione mobile Android o
iOS o con qualsiasi browser internet su https://home.shelly.cloud/. I dispositivi
Shelly® sono accessibili, controllati e monitorati a distanza da qualsiasi luogo in
cui l’utente abbia una connettività Internet, purché i dispositivi siano collegati a un
router Wi-Fi e a Internet. I dispositivi Shelly® hanno un’interfaccia web incorporata
accessibile a http://192.168.33.1 nella rete Wi Fi, creata dal dispositivo in modalità
Access Point, o all’indirizzo URL del dispositivo nella rete Wi-Fi a cui è connesso.
L’interfaccia web incorporata può essere utilizzata per monitorare e controllare il
dispositivo, così come per regolare le sue impostazioni.
I dispositivi Shelly® sono in grado di comunicare direttamente con altri dispositivi
Wi-Fi attraverso il protocollo HTTP. Un’API è fornita da Allterco Robotics EOOD. Per
maggiori informazioni, visitare:
https://shelly-api-docs.shelly.cloud/#shelly-family-overview.
I dispositivi Shelly® vengono consegnati con un rmware installato in fabbrica. Se
sono necessari aggiornamenti del rmware per mantenere i dispositivi in confor-
mità, compresi gli aggiornamenti di sicurezza, Allterco Robotics EOOD fornirà gli
aggiornamenti gratuitamente attraverso l’interfaccia web incorporata del dispo-
sitivo o l’applicazione mobile Shelly, dove sono disponibili le informazioni sulla
versione corrente del rmware. La scelta di installare o meno gli aggiornamenti
del rmware del dispositivo è di esclusiva responsabilità dell’utente. Allterco Ro-
botics EOOD non è responsabile per qualsiasi mancanza di conformità del dispo-
sitivo causata dalla mancata installazione degli aggiornamenti forniti dall’utente
in modo tempestivo.
Shelly Plus H&T (il Dispositivo) è un sensore di umidità e temperatura intelligente
Wi-Fi.
Istruzioni per l’installazione
⚠ATTENZIONE! Non utilizzare il Dispositivo se è stato danneggiato.
⚠ATTENZIONE! Non tentare di riparare il Dispositivo da solo.
1. Alimentazione
Shelly Plus H&T può essere alimentato da 4 batterie AA (LR6) da 1,5 V o da un
adattatore di alimentazione USB Type-C.
⚠ATTENZIONE! Utilizza il dispositivo solo con batterie o adattatori di alimentazio-
ne USB Type-C conformi a tutte le normative vigenti. Batterie o adattatori di alimen-
tazione inadeguati possono danneggiare il Dispositivo e causare incendi.
A. Batterie
Rimuovi il coperchio posteriore del dispositivo con un cacciavite piatto come mo-
strato in gura 1, inserisci le batterie della la inferiore come mostrato in gura 3 e
le batterie della la superiore come mostrato in gura 4.
⚠ATTENZIONE! Assicurati che i segni + e - delle batterie corrispondano alla mar-
catura sul vano batterie del dispositivo (g. 2 A).
B. Adattatore di alimentazione USB Tipo-C
Inserisci il cavo dell’adattatore di alimentazione USB Type-C nella porta USB
Type-C del dispositivo (g. 2 C).
⚠ATTENZIONE! Non collegare l’adattatore al dispositivo se l’adattatore o il cavo
sono danneggiati.
⚠ATTENZIONE! Scollega il cavo USB prima di rimuovere o riporre il coperchio
posteriore.
⚠IMPORTANTE: il Dispositivo non può essere utilizzato per caricare batterie ri-
caricabili.
2. Avvio
Quando viene alimentato inizialmente, il dispositivo entra in modalità Setup e il di-
splay mostra SEt al posto della temperatura. Per impostazione predenita, il punto
di accesso del dispositivo è abilitato, come indicato da AP nell’angolo in basso a
destra del display. Se non è abilitato, tieni premuto il pulsante Reset (g. 2 B) per
5 secondi per abilitarlo.
⚠IMPORTANTE: per risparmiare le batterie, il dispositivo rimane in modalità Setup
per 3 minuti e poi passa in modalità Sleep e il display mostra la temperatura misu-
rata. Premi brevemente il pulsante Reset per tornare in modalità Setup. Premendo
brevemente il pulsante Reset mentre il dispositivo è in modalità Setup, il dispositivo
passa in modalità Sleep.
3. Inclusione a Shelly Cloud
Se si sceglie di utilizzare il dispositivo con l’applicazione mobile Shelly Cloud e il
servizio Shelly Cloud, le istruzioni su come collegare il dispositivo al Cloud e con-
trollarlo attraverso l’App Shelly si trovano nella “Guida App”. L’applicazione mobile
Shelly e il servizio Shelly Cloud non sono condizioni per il corretto funzionamento
del Dispositivo. Questo Dispositivo può essere utilizzato con vari altri servizi e ap-
plicazioni di automazione domestica.
⚠ATTENZIONE! Non permettere ai bambini di giocare con i pulsanti/interruttori
collegati al Dispositivo. Tenere i dispositivi per il controllo remoto di Shelly (telefoni
cellulari, tablet, PC) lontano dai bambini.
4. Collegamento manuale a una rete Wi-Fi locale
Shelly Plus H&T può essere gestito e controllato attraverso la sua interfaccia web
integrata. Assicurati che il dispositivo sia in modalità Setup, che il suo punto di
accesso sia abilitato e che tu sia connesso con un dispositivo Wi-Fi. Da un browser
web apri l’interfaccia web del dispositivo navigando verso 192.168.33.1. Clicca sul
pulsante Reti e poi espandi la sezione Wi.
Abilita la rete Wi1 e/o Wi2 (rete di backup) selezionando l’interruttore corri-
spondente. Inserisci il nome della rete Wi-Fi (SSID) o selezionala cliccando sul
link grigio Clicca qui per selezionare la rete. Inserisci la password della rete Wi-Fi
e clicca su APPLICA.
L’URL del dispositivo apparirà in blu nella parte superiore della sezione Wi, quan-
do il dispositivo si sarà connesso correttamente alla rete Wi-Fi.
⚠RACOMMANDAZIONE: per motivi di sicurezza si consiglia di disabilitare la mo-
dalità AP dopo che il dispositivo si è connesso con successo alla rete Wi-Fi locale.
Espandi la sezione Punto di accesso e attiva l’interruttore Abilita.
Quando sei pronto per includere il dispositivo in Shelly Cloud o in un altro servizio,
⚠CAUTION! Unplug the USB cable before removing or placing the back cover.
5. Attaching the stand
If you want to place the Device on your desk, on a shelf or any other horizontal
surface, attach the stand as shown on g. 5.
6. Wall mounting
If you want to mount the Device on a wall or any other vertical surface use the back
cover to mark the wall where you want to mount the Device.
⚠CAUTION! Do not drill through the back cover.
Use screws with head diameter between 5 and 7 mm and max 3 mm thread diame-
ter to x the Device to a wall or another vertical surface.
Another option to mount the Device is using a double sided foam sticker.
⚠CAUTION! The Device is intended for indoor use only.
⚠CAUTION! Protect the Device from dirt and moisture.
⚠CAUTION! Do not use the Device in a damp environment and avoid water splash-
ing.
Reset button actions
The Reset button is shown on g.2 B.
Press briey:
• If the Device is in Sleep mode, puts it in Setup mode.
• If the Device is in Setup mode, puts it in Sleep mode.
Press and hold for 5 sec: If the Device is in Setup mode, enables its access point.
Press and hold for 10 sec: If the Device is in Setup mode, factory resets the Device.
Display
• The Device is in Setup mode.
• The Device access point is enabled.
• Humidity
• The Device is receiving over-the-air update. Shows the progress in percents
instead of the humidity.
• Device has reported current readings to the Cloud. If missing, the current
readings on the display are not yet reported. In this case the readings on
the display may differ from the ones in the Cloud.
• Wi-Fi signal strength indicator
• Indicates battery level. Shows an empty battery when USB powered.
•
Bluetooth connectivity is enabled. Bluetooth is used for inclusion. It can be
disabled from the Shelly app or the Device local web interface.
• ▲ Error while updating the Device rmware
Specication
• Power supply:
 - Batteries: 4 AA (LR6) 1.5 V (batteries not included)
 - USB power supply: Type-C (cable not included)
• Estimated battery life: Up to 12 months (alkaline batteries)
• Humidity sensor measurement range: 0-100%
• Working temperature: 0°C-40°C
• Radio signal power: 1mW
• Radio protocol: Wi-Fi 802.11 b/g/n
• Frequency: 2412-2472 МHz; (Max. 2483,5 MHz)
• Max RF output power Wi-Fi: 15 dBm
• Dimensions without stand (HxWxD): 70x70x26 mm
• Dimensions with stand (HxWxD): 70x70x45 mm
• Operational range: up to 50 m outdoors / up to 30 m indoors
• Bluetooth: v.4.2
• Bluetooth modulation: GFSK, π/4-DQPSK, 8-DPSK
• Bluetooth frequency: TX/RX - 2402 - 2480MHz
• Max. RF output power Bluetooth: 5 dBm
• Webhooks (URL actions): 10 with 2 URLs per hook
• MQTT: Yes
• CPU: ESP32
• Flash: 4 MB
Declaration of conformity
Hereby, Allterco Robotics EOOD declares that the radio equipment type for Shelly
Plus H&T is in compliance with Directive 2014/53/EU, 2014/35/EU, 2014/30/EU,
2011/65/EU. The full text of the EU declaration of conformity is available at the
following internet address:
https://shelly.cloud/knowledge-base/devices/shelly-plus-ht/
Manufacturer: Allterco Robotics EOOD
Address: Bulgaria, Soa, 1407, 103 Cherni vrah Blvd.
Tel.: +359 2 988 7435
E-mail: support@shelly.cloud
Web: https://shelly.cloud
Changes in the contact data are published by the Manufacturer at the ocial web-
site of the Device https://shelly.cloud
All rights to trademark Shelly®, and other intellectual rights associated with this
Device belong to Allterco Robotics EOOD.
tivieren, nachdem das Gerät erfolgreich mit dem lokalen Wi-Fi-Netzwerk verbunden
wurde. Erweitern Sie den Abschnitt Zugangspunkt und schalten Sie den Schalter
Aktivieren um.
Wenn Sie bereit sind, das Gerät in die Shelly Cloud oder einen anderen Dienst ein-
zubinden, schließen Sie die hintere Abdeckung.
⚠VORSICHT! Ziehen Sie das USB-Kabel ab, bevor Sie die hintere Abdeckung ent-
fernen oder anbringen.
5. Befestigen des Ständers
Wenn Sie das Gerät auf Ihrem Schreibtisch, in einem Regal oder auf einer anderen
horizontalen Fläche aufstellen möchten, bringen Sie den Ständer wie in Abb. 5 ge-
zeigt an.
6. Wandmontage
Wenn Sie das Gerät an einer Wand oder einer anderen vertikalen Fläche anbringen
möchten, markieren Sie die Wand, an der Sie das Gerät anbringen möchten, mit
der hinteren Abdeckung.
⚠VORSICHT! Bohren Sie nicht durch die hintere Abdeckung.
Verwenden Sie Schrauben mit einem Kopfdurchmesser zwischen 5 und 7 mm und
einem maximalen Gewindedurchmesser von 3 mm, um das Gerät an einer Wand
oder einer anderen vertikalen Fläche zu befestigen.
Eine weitere Möglichkeit zur Befestigung des Geräts ist die Verwendung eines dop-
pelseitigen Schaumstoffaufklebers.
⚠VORSICHT! Das Gerät ist nur für die Verwendung in Innenräumen vorgesehen.
⚠VORSICHT! Schützen Sie das Gerät vor Schmutz und Feuchtigkeit.
⚠VORSICHT! Verwenden Sie das Gerät nicht in einer feuchten Umgebung und ver-
meiden Sie Wasserspritzer.
Aktionen der Reset-Taste
Die Reset-Taste ist in Abb.2 B dargestellt.
Drücken Sie sie kurz:
• Wenn sich das Gerät im Ruhemodus bendet, wird es in den Setup-Modus ver-
setzt.
• Wenn sich das Gerät im Setup-Modus bendet, wird es in den Ruhemodus ver-
setzt.
5 Sekunden lang drücken: Wenn sich das Gerät im Setup-Modus bendet, wird
sein Zugangspunkt aktiviert.
10 Sekunden lang gedrückt halten: Wenn sich das Gerät im Setup-Modus bendet,
wird das Gerät auf Werkseinstellungen zurückgesetzt.
Anzeige
• Das Gerät bendet sich im Setup-Modus.
• Der Zugangspunkt des Geräts ist aktiviert.
• Luftfeuchtigkeit
• Das Gerät erhält ein Over-the-Air-Update. Zeigt den Fortschritt in Prozent
anstelle der Luftfeuchtigkeit an.
• Das Gerät hat aktuelle Messwerte an die Cloud gemeldet. Fehlt diese Anga-
be, werden die aktuellen Messwerte auf dem Display noch nicht gemeldet.
In diesem Fall können die Messwerte auf dem Display von denjenigen in
der Cloud abweichen.
• Anzeige der Wi-Fi-Signalstärke
• Zeigt den Batteriestand an. Zeigt eine leere Batterie an, wenn das Gerät
über USB mit Strom versorgt wird.
•
Die Bluetooth-Verbindung ist aktiviert. Bluetooth wird für die Aufnahme ver-
wendet. Sie kann über die Shelly App oder die lokale Webschnittstelle des
Geräts deaktiviert werden.
• ▲ Fehler beim Aktualisieren der Gerätermware
Technische Daten
• Stromversorgung:
 - Batterien: 4 AA (LR6) 1,5 V (Batterien nicht enthalten)
 - USB-Stromversorgung: Typ-C (Kabel nicht enthalten)
• Geschätzte Lebensdauer der Batterie: Bis zu 12 Monate (Alkali-Batterien)
• Messbereich des Luftfeuchtigkeitssensors: 0-100%
• Arbeitstemperatur: 0°C-40°C
• Leistung des Funksignals: 1mW
• Funkprotokoll: Wi-Fi 802.11 b/g/n
• Frequenz: 2412-2472 МHz; (Max. 2483,5 MHz)
• Maximale RF-Ausgangsleistung Wi-Fi: 15 dBm
• Abmessungen ohne Ständer (HxBxT): 70x70x26 mm
• Abmessungen mit Standfuß (HxBxT): 70x70x45 mm
• Betriebsreichweite: bis zu 50 m im Freien / bis zu 30 m in Gebäuden
• Bluetooth: v.4.2
• Bluetooth-Modulation: GFSK, π/4-DQPSK, 8-DPSK
• Bluetooth-Frequenz TX/RX - 2402 - 2480MHz
• Maximale RF-Ausgang Bluetooth: 5 dBm
• Webhooks (URL-Aktionen): 10 mit 2 URLs pro Hook
• MQTT: Ja
• CoAP: Ja
• REST-API: Ja
• CPU: ESP32
• Flash: 4MB
Konformitätserklärung
Hiermit erklärt Allterco Robotics EOOD, dass der Funkanlagentyp Shelly Plus H&T
der Richtlinie 2014/53/EU, 2014/35/EU, 2014/30/EU, 2011/65/EU entspricht. Den
vollständigen Text der EU-Konformitätserklärung nden Sie unter folgender Inter-
netadresse
https://shelly.cloud/knowledge-base/devices/shelly-plus-ht/
Hersteller: Allterco Robotics EOOD
Adresse: 103 Cherni vrah Blvd., 1407 Soa, Bulgarien
Tel.: +359 2 988 7435
E-Mail: support@shelly.cloud
Internet: https://www.shelly.cloud
Änderungen der Kontaktdaten werden vom Hersteller auf dessen oziellen Web-
site veröffentlicht
Alle Rechte an der Marke Shelly® und anderen geistigen Eigentumsrechten im Zu-
sammenhang mit diesem Gerät gehören Allterco Robotics EOOD.
posiziona il coperchio posteriore.
⚠ATTENZIONE! Scollega il cavo USB prima di rimuovere o posizionare il coperchio
posteriore.
5. Fissare il supporto
Se vuoi posizionare il Dispositivo sulla scrivania, su una mensola o su qualsiasi
altra supercie orizzontale, ssa il supporto come mostrato nella gura 5.
6. Montaggio a parete
Se vuoi montare il dispositivo su una parete o su un’altra supercie verticale, usa
il coperchio posteriore per segnare la parete su cui vuoi montare il dispositivo.
⚠ATTENZIONE! Non forare il coperchio posteriore.
Per ssare il dispositivo alla parete o a un’altra supercie verticale, utilizza viti con
diametro della testa compreso tra 5 e 7 mm e diametro massimo della lettatura
di 3 mm.
Un’altra opzione per montare il dispositivo è l’utilizzo di un adesivo biadesivo.
⚠ATTENZIONE! Il Dispositivo è destinato esclusivamente all’uso in ambienti in-
terni.
⚠ATTENZIONE!Proteggi il Dispositivo da sporco e umidità.
⚠ATTENZIONE!Non utilizzare il dispositivo in un ambiente umido ed evita gli
schizzi d’acqua.
Azioni del pulsante di reset
Il pulsante di reset è mostrato nella g. 2 B.
Premilo brevemente:
• Se il dispositivo è in modalità Sleep, passa alla modalità Setup.
• Se il dispositivo è in modalità Setup, passa in modalità Sleep.
Tieni premuto per 5 secondi: se il dispositivo è in modalità Setup, attiva il suo
punto di accesso.
Tieni premuto per 10 secondi: se il dispositivo è in modalità Impostazione, esegue
il reset di fabbrica del dispositivo.
Display
• Il dispositivo è in modalità di congurazione.
•
Il punto di accesso del dispositivo è abilitato.
• Umidità
•
Il dispositivo sta ricevendo un aggiornamento via etere. Mostra l’andamen-
to in percentuale invece dell’umidità.
• Il dispositivo ha segnalato le letture correnti al Cloud. Se manca, i valori
attuali sul display non sono ancora stati segnalati. In questo caso, le letture
sul display possono differire da quelle nel Cloud.
• Indicatore della potenza del segnale Wi-Fi
• Indica il livello della batteria. Mostra una batteria scarica quando è alimen-
tato via USB.
•
La connettività Bluetooth è abilitata. Il Bluetooth viene utilizzato per l’inclu-
sione. Può essere disattivata dall’applicazione Shelly o dall’interfaccia web
locale del dispositivo.
• ▲ Errore durante l’aggiornamento del rmware del dispositivo
Speciche tecniche
• Alimentazione:
 - Batterie: 4 AA (LR6) 1,5 V (batterie non incluse)
 - Alimentazione USB: Tipo-C (cavo non incluso)
• Durata stimata della batteria: Fino a 12 mesi (batterie alcaline)
• Intervallo di misurazione del sensore di umidità: 0-100%
• Temperatura di lavoro: 0°C-40°C
• Potenza del segnale radio: 1mW
• Protocollo radio: Wi-Fi 802.11 b/g/n
• Frequenza: 2412-2472 МHz; (Max. 2483,5 MHz)
• Potenza massima di uscita RF: 15 dBm
• Dimensioni senza supporto (HxLxP): 70x70x26 mm
• Dimensioni con supporto (HxLxP): 70x70x45 mm
• Raggio d’azione: no a 50 m all’aperto / no a 30 m al chiuso
• Bluetooth: v.4.2
• Modulazione Bluetooth: GFSK, π/4-DQPSK, 8-DPSK
• Frequenza Bluetooth TX/RX - 2402 - 2480MHz
• Uscita massima RF Bluetooth: 5 dBm
• Webhook (azioni URL): 10 con 2 URL per ogni hook
• MQTT: Sì
• CoAP: Sì
• API REST: Sì
• CPU: ESP32
• Flash: 4MB
Dichiarazione di conformità
Con la presente, Allterco Robotics EOOD dichiara che il tipo di apparecchiatura ra-
dio Shelly Plus H&T è conforme alla Direttiva 2014/53/UE, 2014/35/UE, 2014/30/
UE, 2011/65/UE. Il testo completo della dichiarazione di conformità UE è disponi-
bile al seguente indirizzo internet
https://shelly.cloud/knowledge-base/devices/shelly-plus-ht/
Produttore: Allterco Robotics EOOD
Indirizzo: Bulgaria, Soa, 1407, 103 Cherni vrah Blvd.
Tel.: +359 2 988 7435
E-mail: support@shelly.cloud
Web: https://www.shelly.cloud
Le modiche ai dati di contatto sono pubblicate dal Produttore sul sito Web u-
ciale del Dispositivo
Tutti i diritti sul marchio Shelly® e altri diritti intellettuali associati a questo dispo-
sitivo appartengono a Allterco Robotics EOOD.
g.1 g.2
g.5g.3 g.4
24/2022

Chat with your Shelly Plus H&T manual using AI

Get instant AI answers from your Shelly Plus H&T manual

Ask anything about the Shelly Plus H&T. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend Plus H&T?

Yes No

Frequently Asked Questions

A

First, power on the device and wait for the AP indicator to appear. Connect your phone or computer to the device's temporary hotspot. Open a browser and go to 192.168.33.1. Navigate to the Networks section, select your Wi-Fi SSID, enter the password, and click Apply. Once connected, the URL will turn blue.

Is this answer helpful?

A

No, the Shelly Plus H&T is designed for indoor use only. Exposure to rain, snow, or high humidity can damage the electronics. While it has a decent range, it must be kept dry and protected from direct weather elements.

Is this answer helpful?

A

Using standard alkaline AA batteries, the device can last up to 12 months. This duration varies based on how frequently the device wakes up to report data and the strength of your Wi-Fi signal.

Is this answer helpful?

A

Yes, the Shelly Plus H&T functions perfectly as a standalone device on your local network. You can monitor and control it via the embedded web interface or integrate it with other home automation platforms without needing the cloud service.

Is this answer helpful?

A

To reset the device, press and hold the Reset button for 10 seconds while the device is in Setup mode. This will restore all settings to their original factory defaults, erasing any saved Wi-Fi credentials.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Supports both battery and USB power for maximum flexibility
  • No hub required; works directly over local Wi-Fi networks
  • Compatible with multiple automation protocols including MQTT and HTTP
  • Compact and lightweight design suitable for wall or shelf mounting
  • Free firmware updates available via the embedded web interface
VS

Disadvantages

  • Batteries and USB cables are not included in the package
  • Device is strictly for indoor use and cannot withstand damp environments
  • Setup requires manual Wi-Fi configuration via web interface initially
  • Battery life depends heavily on usage frequency and signal strength
  • Display goes dark in sleep mode which may hide real-time readings
M: QW-35-FL

Product Specification

Type

Sensor

Standard

WLAN (802.11b/g/n), Bluetooth LE

Function

Temperature, Humidity

Topology

Star, Mesh

Dimensions

2.76x2.76x1.02 in

Features

Display, battery powered (4x AA), app controlled (Android, iOS), voice assistant (Amazon Alexa, Google Assistant)

M: QW-35-FL

Product Description

Discover the Shelly Plus H&T: Your Smart Home Climate Guardian

The Shelly Plus H&T is a versatile Wi-Fi smart sensor designed to bring precision and intelligence to your home environment monitoring. As part of the innovative Shelly ecosystem, this device allows you to track temperature and humidity levels with remarkable accuracy from anywhere in the world. Whether you are managing a cozy living room or a sensitive storage area, this sensor ensures you never miss a fluctuation in your indoor climate.

Powered by either four AA batteries or a convenient USB Type-C adapter, the Shelly Plus H&T offers flexible installation options. It operates seamlessly within local Wi-Fi networks without requiring a hub, communicating directly via HTTP protocols for integration with various home automation systems. The embedded web interface provides immediate access to settings and real-time data, while optional cloud connectivity through Shelly Cloud enables remote control via mobile apps on Android or iOS devices.

Installation is straightforward, featuring a compact design that fits easily on shelves or mounts securely on walls using included stands or adhesive tape. The device features an intuitive display that shows current readings, battery status, and connection signals. For energy efficiency, it automatically enters sleep mode after setup, waking up only when triggered by the reset button or when reporting new data. With support for MQTT, CoAP, and REST APIs, it integrates effortlessly into complex smart home setups, making it a reliable choice for modern automation enthusiasts.

Key Features and Benefits

  • Dual Power Options: Run on long-lasting alkaline batteries or continuous USB power.
  • Local Control: Manage settings directly via a built-in web interface without internet dependency.
  • Smart Integration: Compatible with major platforms via standard protocols like MQTT and HTTP.
  • Compact Design: Small footprint allows for discreet placement in any room.
  • Real-Time Monitoring: Instant updates on temperature and humidity with clear visual indicators.

Important Safety Notes

Always ensure the device is used indoors only and protected from moisture. Do not attempt to repair the unit yourself; always disconnect power before handling the back cover. Keep children away from the device and its remote controls to prevent accidental resets.

M: QW-35-FL

© Copyright 2026 Manual.ly