Manual.ly Logo

sera X-Edge Manual

0.0 · 0 Ratings

PDF manual · 56 Pages

English

M: OA-GPT-5-NAN
page

/ 56

Loading...
a7ae3dc99414fd7b0d4290e14dfd1344b0be page 9
9
Operation
Separating the filter from the mains supply
The corner filter can be switched off by pulling the mains
plug.
Assembly and installation in the aquarium
Step 1: Filling in filter media
The filter is already filled with filter media and immediately
ready for use upon purchase (1).
Step 2: Positioning
The sera X-Edge 300, 450, 700 are exclusively installed in a
corner of the aquarium.
Please note that the filter must be submerged completely in
the water for preventing it from running dry, which would
damage the motor (not a guaranty case!). The best
installation height is usually 2 – 3 cm (0.8 – 1.2 in.) underneath
the water surface (2). This ensures good gas exchange due
to increased surface current and, consequently, optimal
oxygen transfer into the aquarium water.
Press the filled filter with the holder plate attached to it
vertically in the chosen pre-cleaned corner of the aquarium.
The suction cups cannot hold properly when algae or similar
periphyton grow on the glass. In that case possibly use a
blade cleaner for cleaning the installation location first. The
holder plate has 4 suction cups and immediately attaches to
the aquarium glass. If you should wish to install the filter in a
not yet filled aquarium, you should at least moisten the
suction cups so these will attach to the glass. Hold the filter
from below in an inclined position and hook the filter head
with its gap on the back into the holder. Now lean the filter
against the corner of the aquarium until the holder snaps in.
Now the corner stripe touches the silicone joint of the
aquarium (3). Removing and inserting the filter from or into
the holder requires some space and should be considered
when setting up the aquarium.
Step 3: Pushing on the outlet options
Choose the correct outlet type for your aquarium. The spray
bar produces a directed current (4), the duck beak nozzle
rather a soft volume current (5). The air set can only be used
in combination with the duck beak nozzle (13), otherwise the
plug must be pushed into the air intake opening. The spray
bar or the duck beak nozzle are simply pushed into theoutlet
opening of the corner filter. Now you can turn the chosen
outlet option into thedesired position. Connect the power
supply only when the filter is positioned and installed
correctly. Check whether the achieved effect meets your
desires and possibly readjust the current.
Step 4: Start and adjusting the flow rate
When the filter is submerged it can be switched on by
connecting the mains plug. Turning the adjustment knob (6)
allows adjusting the flow rate accordingly.
Technical data
sera X-Edge 300 sera X-Edge 450 sera X-Edge 700
220 – 240 V ~ 50 Hz
4.2 W
Q
max
300 l/h
H
max
0.4 m
220 – 240 V ~ 50 Hz
5 W
Q
max
450 l/h
H
max
0.6 m
220 – 240 V ~ 50 Hz
8.5 W
Q
max
700 l/h
H
max
0.8 m
IPX8
35°C
max.
T
Maintenance and cleaning
Cleaning (every 2 weeks)
Switch the sera X-Edge corner filter off by pulling the mains
plug. Grab underneath the filter body and pull the filter
casing upward towards you until the filter is released from
the holder with a click. Now you can separate the filter
casing from the motor part (7) by gentle pressure and take it
out of the aquarium for cleaning.
Remove the front cover with grid from the filter casing. You
can now take the filter mat out of the holder for cleaning or
replacing it (8). Remove the filter basket and the filter sponge
from the filter casing (9) and clean it under running water or,
even better, in a bucket with aquarium water which is being
disposed of anyway after the water change.
The filter mat insert only fits into the front cover with grid in
one direction. Please note the triangle mark on the intake
grid that marks the snap-in location of the little hinge of the
filter mat insert (10).
If you only wish to clean or replace the mat you can remove
the intake grid from the filter body under water and remove
the mat from it (11) after having switched off the filter. Pay
attention to the correct position of the mat insert and the
intake grid during assembly.
Maintenance of the running unit (every 3 months)
Remove the motor chamber cover and take the rotor out of
the motor chamber (12). Rinse rotor and pump head under
running water and re-assemble the parts in reverse order.
Possible problem sources and solution
Please use the extensive information for use about this
topic on our web site www.sera.de.
Disposal of the unit
Waste electrical and electronic equipment (WEEE) must
not get into domestic waste!
If ever the unit cannot be used anymore, the consumer is
legally obliged to hand in waste electrical and electronic
equipment (WEEE) separately from domestic waste, e.g.
at a collection point of his community/his district. This
ensures that waste electrical and electronic equipment
(WEEE) is expertly processed and that negative effects to the
environment are avoided.
Therefore electrical and electronic
equipment bears the following symbol:
Manufacturer guaranty
We, sera GmbH (warrantor), Borsigstraße 49, 52525
Heinsberg, Germany, grant our customers a 2 year
guaranty* for the sera X-Edge corner filters covering
freedom of defects in material and production, commencing
on the purchase date.
The 2 year sera guaranty is to be understood as an
additional service of the manufacturer and not as a
replacement for your rights arising from §§ 437 BGB
(German Civil Code). Your statutory rights are not limited by
this guaranty. Claims arising from statutory liability for
defects are also not affected!
Guaranty exclusion (*)
The following parts are excluded from guaranty:
a. Guaranty does NOT apply for wear and tear parts such as
filter media,running unit (rotor, bearing, shaft), suction
cups.
P21565_sera-X-Edge_GBI_21565_neu_2.indd 9 25.03.2022 15:24:18

Chat with your sera X-Edge manual using AI

Get instant AI answers from your sera X-Edge manual

Ask anything about the sera X-Edge. Answers come from this manual, with the pages they are based on.

X-Edge Maintenance Schedule

Remind me when maintenance is due
Every 2 weeks
Clean the filter media and housing

Disconnect power. Clean the filter mat, basket and sponge under running water or preferably in discarded aquarium water; replace the mat if needed.

Quarterly
Clean the rotor and pump head

Remove the motor chamber cover and rotor, rinse the rotor and pump head under running water, then reassemble in reverse order.

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: gpt-5.6-terra

Ask a Question

0/1000

Do you recommend X-Edge?

Yes No

Frequently Asked Questions

A

X-Edge 300 is intended for freshwater tanks up to ~100 L, X-Edge 450 for up to ~200 L and X-Edge 700 for up to ~300 L — capacity depends on stocking density and flow preferences.

Is this answer helpful?

A

No. The filter must be fully submerged during operation. Running it dry or with insufficient water flow can cause motor damage and void the warranty.

Is this answer helpful?

A

Clean the filter mat, sponge and basket every two weeks (use aquarium water for rinsing when possible). Service the running unit by removing and rinsing the rotor and pump head every three months.

Is this answer helpful?

A

Use the spray bar for a directed current and stronger surface movement; choose the duck-bill nozzle for a softer volumetric flow. The Air-Set can be combined with the duck-bill nozzle for added aeration.

Is this answer helpful?

A

Always unplug before maintenance, form a drip loop on the mains cable, keep the plug and socket dry, do not operate above 35°C, keep out of reach of children under 8, and ensure RCD protection on the circuit if possible.

Is this answer helpful?

A

sera offers a 2-year manufacturer warranty against material and workmanship defects. Exclusions include wear parts (filter media, rotor, suction cups), power cable damage, damage from misuse (dry-running), external impacts, and saltwater use.

Is this answer helpful?

A

First unplug and inspect the intake mat, sponge and rotor for debris. Clean components in aquarium water, verify correct assembly and seating of the mat (observe triangle mark), then reassemble and retest. Consult the full manual or sera.de for troubleshooting.

Is this answer helpful?

M: OA-GPT-5-NAN

Advantages and Disadvantages

Advantages

  • Pre-filled, easy to install corner design keeps aquarium layout tidy and unobtrusive.
  • Low power consumption (4.2–8.5 W) with quiet motor thanks to noise damping and glass mounting.
  • Adjustable flow options (spray bar, duck-bill, Air-Set) let you tune circulation to tank needs.
  • Simple maintenance: tool-free removal, biweekly cleaning of mat/sponge and quarterly rotor service.
  • Includes biological media (sera siporax mini Professional) for stable biological filtration out of box.
VS

Disadvantages

  • Must remain fully submerged; dry-running will damage motor and void warranty.
  • Suction cups require clean glass to adhere; algae can prevent secure mounting.
  • Air-Set only usable with duck-bill nozzle; air inlet must be closed otherwise.
  • Power cable damage excluded from warranty and cannot be repaired by manufacturer.
  • Not suitable for marine use and warranty void if used in saltwater.
M: OA-GPT-5-NAN

Product Specification

Type

Internal filter

Suitability

Freshwater, Aquatics, Terraristics, Breeding tank

Filtration

1x Filter basket (Ceramic substrate, siporax mini Professional), 1x Sponge filter (coarse), 1x Filter fleece

Special features

Rotatable filter outlet, Suction cup mount

Manufacturer's warranty

two years

M: OA-GPT-54-NAN

Product Description

sera X-Edge Unterschrank 100cm Manual

The sera X-Edge corner filter series (300 / 450 / 700) is a compact, energy-efficient internal aquarium filter designed to sit unobtrusively in a tank corner. Built for freshwater aquariums of varying sizes, the X-Edge combines mechanical and biological filter media with a quiet, low-maintenance motor to deliver clear water and stable biological conditions. Its corner-mounted design, suction-cup holder plate and interchangeable outlet fittings (spray bar, duck-bill nozzle, Air-Set) let you tailor flow patterns to tank layout and livestock needs.

Installation is straightforward: the unit ships pre-filled with filter media and is installed vertically in a cleaned aquarium corner, typically 2–3 cm below the surface for optimal gas exchange. The holder plate secures with four suction cups; ensure glass is free of algae for reliable adhesion. The filter head contains an adjustable flow knob and a pivoting outlet tube. Choose the spray bar for directed currents or the duck-bill nozzle for softer volumetric flow. The Air-Set is used only with the duck-bill nozzle; otherwise the air inlet must be closed.

Maintenance is simple and tool-free: biweekly cleaning involves removing the filter casing from the motor housing, replacing or rinsing the mat, sponge and media (use aquarium water when possible), and reassembling following the orientation marks. Every three months, the rotor and pump head should be rinsed to keep the running unit efficient. The design supports quick partial service or full disassembly for deep cleaning.

Safety and usage notes stress that the filter must always remain fully submerged to avoid dry-running and motor damage, operate only in freshwater indoor tanks, and not exceed 35°C. Keep the mains plug dry and form a drip loop on the cable; unplug before any maintenance and do not operate without filter media. Damaged power cords must be replaced by the manufacturer or qualified personnel. The product contains magnetic components—pacemaker users should observe device-specific safety distances.

Models and specs vary by capacity: the X-Edge 300 suits aquariums up to ~100 L with Qmax 300 l/h, the 450 up to ~200 L with Qmax 450 l/h, and the 700 up to ~300 L with Qmax 700 l/h. Power consumption is low (approx. 4.2–8.5 W) and the units are IPX8 rated for submersion. The kit includes the filter head, holder plate with suction cups, filter case, pre-filled filter basket (sera siporax mini Professional), sponge, mat/activated carbon insert, front cover, spray bar, duck-bill nozzle, Air-Set and user information.

Using the X-Edge correctly yields quiet, efficient filtration with easy access for routine maintenance, while observing safety and warranty exclusions protects performance and coverage.

Notes

  • Unit ships pre-filled and ready to run; always check suction cup adhesion before powering.
  • Close the air injector when not using Air-Set to prevent leaks.
  • Warranty excludes wear parts, power cable damage, dry-running and misuse.
M: OA-GPT-5-NAN

© Copyright 2026 Manual.ly