Manual.ly Logo

Rothenberger ROMAX 4000 Manual

0.0 · 0 Ratings

PDF manual · 276 Pages

English

M: QW-35-FL
page

/ 276

Loading...
57cc35bcbbbb55074269fa1050e84b22c797 page 1c
20
ENGLISH
Li-ion battery packs have a capacity and signal indicator: (6)
Press the button (5), the LEDs indicate the charge level.
If one LED is flashing, the battery pack is almost flat and must be recharged.
Handling
Charging battery pack:
Push the battery pack completely to the stop on the sliding seat (2).
The operating indicator (3) flashes.
Conservation charge:
Once the charging process has finished, the battery charger automatically switches to conserva-
tion mode.
The battery pack can remain in the battery charger and is therefore always ready for use.
The operating display (3) lights up continuously.
Fault:
● Warning display (4) lights up continuously.
Battery pack is not charged. Temperature too high/ too low. When the temperature of the battery
pack is between 0 °C and 50 °C / 32° - 122° F, the charging process begins automatically.
● Warning display (4) flashes.
Battery pack is defective. Remove the battery pack immediately from the charger.
The battery pack was not pushed correctly onto the sliding seat (2).
5 Care and Maintenance
ROMAX 4000:
Remove the battery prior to carrying out any work on the machine.
Check that the press jaws are fully functional. Damaged press jaws must not be used and must
be sent to an authorised ROTHENBERGER repair shop.
Check that the press jaw and drive rolls move freely.
Check the bolt for signs of damage at regular intervals. Have damaged bolts replaced by an au-
thorised ROTHENBERGER repair shop.
Clean and grease the drive rolls, the bolt and press jaws when you have finished work.
Use only high quality pressing or ball bearing grease.
The pressing contour must be kept free of grease.
All other servicing, maintenance and repair work must be carried out by an authorized
ROTHENBERGER repair shop.
If the seal is damaged the warranty will be null and void.
After 40.000 pressing cycles or 2 years have the machine serviced by an authorized ROTHEN-
BERGER workshop.
When dispatching the machine ensure that it is packed in its carrying case completely with bat-
tery and charger in the carry case only.
Electro-hydraulic machine does not exceed 3 hours in a -5° C / 23°F storage.
Disconnect battery from machine before storing.
Charger:
Repairs to the charger must only be carried out by qualified electricians.

Chat with your Rothenberger ROMAX 4000 manual using AI

Get instant AI answers from your Rothenberger ROMAX 4000 manual

Ask anything about the Rothenberger ROMAX 4000. Answers come from this manual, with the pages they are based on.

ROMAX 4000 Maintenance Schedule

Remind me when maintenance is due
Every 2 years or 40,000 presses
Professional machine service

Have the machine serviced by an authorized ROTHENBERGER workshop after 40,000 pressing cycles or every 2 years, whichever comes first.

Show in the manual (page 28)
After every use
Clean and grease drive rolls, bolt, and press jaws

When finished working, clean and grease the drive rolls, bolt, and press jaws using high-quality pressing or ball bearing grease. Keep the pressing contour free of grease.

Show in the manual (page 28)
Regularly
Inspect bolt for damage

Check the bolt for signs of damage at regular intervals. Have damaged bolts replaced by an authorized ROTHENBERGER repair shop.

Show in the manual (page 28)
Before each use
Check press jaw functionality and movement

Verify that press jaws are fully functional and move freely with the drive rolls. Do not use damaged press jaws; send them to an authorized service center.

Show in the manual (page 28)

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend ROMAX 4000?

Yes No

Frequently Asked Questions

A

The device generates a maximum piston force of approximately 34 kilonewtons. This capability allows for effective joining of various pipe types and ensures secure compression of fittings during the application process for professional results.

Is this answer helpful?

A

Insert the battery until you hear a click indicating the catch has engaged. To remove, press the release catch mechanism and pull the pack out gently. Always store the spare battery in a cool dry place away from children and metal objects.

Is this answer helpful?

A

No, you should only use original ROTHENBERGER or CAS compatible battery packs. Using non approved batteries may cause explosions or void the safety certification. Check the manual for the specific model codes suitable for this machine.

Is this answer helpful?

A

A full service is recommended after 40,000 pressing cycles or every two years depending on usage intensity. Authorized workshops must perform these checks to ensure safety mechanisms like emergency stops still function correctly.

Is this answer helpful?

A

Yes, the noise level can exceed 85 decibels during operation. You should wear certified hearing protection whenever the motor runs to prevent long term hearing damage for yourself.

Is this answer helpful?

A

The tool functions between negative ten and sixty degrees Celsius. Storage should occur within similar limits to preserve battery chemistry and prevent material deformation in harsh weather conditions.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • High piston force up to 34 kN for strong connections
  • Cordless design offers greater mobility and access
  • LED indicators show status clearly for operator feedback
  • Rotatable press jaws allow angled positioning easily
  • Internal counter tracks presses for maintenance scheduling
VS

Disadvantages

  • Heavier weight when fully loaded with large battery
  • Pricier initial cost than basic electric models
  • Some repairs require authorized workshop visits only
  • Temperature limits restrict outdoor use in extreme cold
  • Warranty voids if internal seals are damaged
M: QW-35-FL

Product Specification

Battery

18V, 4.0Ah, Lithium-Ion

Handle

Plastic

Total Length

17.72in

Package Contents

Case, Charger, Battery

M: QW-35-FL

Product Description

Discover Professional Pipe Fitting Efficiency Today

The Rothenberger ROMAX 4000 Cordless Crimping Tool with case + battery 4.0Ah Manual provides a robust solution for modern plumbing applications. This powerful handheld unit eliminates cable clutter while delivering consistent hydraulic force for every connection. Technicians value the intuitive interface that guides every pressing cycle safely and accurately without guesswork. Emergency stops are strategically placed to protect operators from mechanical hazards during intense work sessions continuously. Safety goggles and gloves remain mandatory gear alongside this premium equipment setup for everyone involved.

Advanced Specifications for Heavy Duty Jobs

Maximum piston force reaches thirty four kilonewtons to ensure secure joint integrity across different pipe materials. Motor speed options allow rapid processing times without sacrificing connection quality or structural strength. Portable designs weigh under three kilograms excluding the power source for reduced operator fatigue. Adjustable jaw rotation angles provide flexibility when accessing confined spaces within complex building infrastructure layouts. Inspection intervals are tracked internally to signal when maintenance checks become necessary for ongoing compliance standards.

Battery Management and Charging Procedures

Original lithium ion packs support extended runtimes throughout full workdays without significant degradation over time. Clear LED indicators warn users instantly regarding charge status before starting critical operations on site. Optimal storage environments prevent thermal damage during off hours between scheduled shifts for the team. Fast charging units return readiness quickly so downtime stays minimal during busy installation schedules regularly. Always verify voltage compatibility before plugging into mains power sources for safety assurance always.

Long Term Reliability and Service Support

Warranty coverage depends heavily on adherence to strict operational guidelines set forth by the manufacturer. Unauthorized repairs may void protections so always contact authorized centers for certified assistance immediately. Spare parts availability ensures machines stay functional year after year through routine upkeep cycles. Proper disposal methods protect the environment when retirement becomes necessary for worn components responsibly. Follow these steps to maximize investment value and maintain high performance standards consistently for all users.

Final Thoughts On Selection Criteria

Choosing the right cordless system impacts productivity rates significantly compared to traditional manual alternatives available previously. Training programs help staff learn proper handling techniques to avoid accidental injuries on site frequently. Regular cleaning extends component lifespan by removing debris accumulation that affects moving parts negatively. Noise levels remain manageable for indoor residential projects requiring quiet work conditions nearby without disturbance. Trustworthy brands deliver confidence when completing critical gas water or heating installations today reliably.

M: QW-35-FL

© Copyright 2026 Manual.ly