Manual.ly Logo

RockShox Reverb AXS Manual

0.0 · 0 Ratings

PDF manual · 43 Pages

English

M: OA-GPT-54-NAN
page

/ 43

Loading...
98d0b16f3d703cd17fd336b68fd588bb46ad page d
13
Check battery levels before and after each
use, and charge or replace batteries as
needed.
If either battery is depleted during use, the
seatpost will remain in the position it is in
until the battery is replaced.
If the AXS controller battery is depleted
during use before the seatpost battery, the
seatpost AXS button can be used to raise or
lower the seatpost.
NOTICE
If the seatpost is compressed and will not
return to full extension, do not manually
pull the seatpost head up to extend.
Vérifiez le niveau de charge de la batterie/
pile avant et après chaque utilisation.
Chargez les batteries ou remplacez les piles
si nécessaire.
Si une batterie se décharge durant
l’utilisation, la tige de selle restera en place
jusqu’à ce que la batterie soit remplacée.
Si la pile de la commande AXS se décharge
durant l’utilisation et avant la batterie de la
tige de selle, le bouton AXS de la tige de
selle peut être utilisé pour baisser ou monter
la selle.
AVIS
Si la tige de selle est abaissée et qu’elle
ne revient pas à sa hauteur maximale,
n’essayez pas de la faire remonter à la
main.
Verifique o nível da bateria antes e depois
de cada uso, e carregue ou substitua as
baterias conforme seja necessário.
Se qualquer das baterias se esgotar durante
o uso, o espigão do assento ficará na
posição em que esteja até que a bateria
seja substituída.
Se a bateria do controlador AXS se esgotar
durante o uso, antes da bateria do espigão
do assento, pode ser usado o botão AXS
do espigão do assento para subir ou baixar
oespigão do assento.
NOTIFICAÇÃO
Se o espigão do selim estiver comprimido
enão regressar à sua completa extensão,
não puxe manualmente para cima a
cabeça do espigão do selim para o
estender.
Überprüfen Sie den Ladezustand der
Batterien vor und nach jeder Fahrt und
laden oder ersetzen Sie die Batterien nach
Bedarf.
Wenn eine Batterie im Gebrauch entladen
ist, bleibt die Sattelstütze in der jeweiligen
Position, bis die Batterie ersetzt wird.
Wenn die Batterie der AXS-Steuerung im
Gebrauch vor der Sattelstützenbatterie
entladen ist, kann die AXS-Taste an der
Sattelstütze verwendet werden, um die
Sattelstütze höher oder niedriger zu stellen.
HINWEIS
Wenn die Sattelstütze nach dem Einfedern
nicht in die vollständig ausgezogene
Position zurückkehrt, versuchen Sie nicht,
den Sattelstützenkopf von Hand nach
oben zu ziehen.
Controllare i livelli delle batterie prima
edopo ogni utilizzo e, se necessario,
caricare o sostituire le batterie.
Se una delle batterie si esaurisce durante
l'uso, il reggisella rimane nella posizione
in cui si trova fino alla sostituzione della
batteria.
Se la batteria del controller AXS si esaurisce
durante l'uso prima della batteria del
reggisella, il pulsante AXS del reggisella può
essere utilizzato per sollevare o abbassare
il reggisella.
AVVISO
Se il reggisella è compresso e non
torna alla piena estensione, non tirare
manualmente la testa del reggisella per
estenderlo.
電池の充電レベルを使用前と使用後に毎回
確認し、必要に応じて電池を充電または交換
してくだ さい 。
使用中にいずれかの電池が消耗してしまった
場合、電池を交換するまで、シートポストは
その時点の位置に留まります。
使用中にシートポストの電池より先に
AXS
コントローラーの電池が消耗した場合は、
シート ポストの
A X S ボタンを使って シートポス
トの上げ下げができます。
注意事項
シートポストを圧縮した際に、完全に伸張し
て戻らない場合は、シートポスト・ヘッドを手
で上に引き上げないでください。
Revise los niveles de las baterías antes y
después de cada uso, y cargue o sustituya
las baterías según sea necesario.
Si alguna de las baterías se agota durante
el uso, la tija de sillín permanecerá en la
posición en la que se encuentre hasta que
sustituya la batería.
Si la batería del controlador AXS se agota
durante el uso antes que la batería de la tija
de sillín, es posible usar el botón AXS de la
tija para subirla o bajarla.
AVISO
Si la tija no vuelve a extenderse del todo
después de haberse comprimido, no
intente tirar de ella manualmente hacia
arriba para extenderla.
Controleer het vermogen van de accu of
batterij voor en na elk gebruik. Laad de accu
op of vervang de batterij, indien nodig.
Als de batterij of accu tijdens gebruik leeg
raakt, blijft de zadelpen in de huidige positie
totdat de batterij of accu wordt vervangen.
Als de batterij in de AXS-controller tijdens
het gebruik voor de accu van de zadelpen
leeg raakt, kan de AXS-knop van de
zadelpen worden gebruikt om de zadelpen
omhoog of omlaag te brengen.
MEDEDELING
Als de zadelpen samengedrukt is en
niet volledig omhoog komt, trek niet
handmatig aan de zadelpen om het
omhoog te brengen.
每次使用前后,请检查电池电量。如有必要,
请将电池充电或更换。
如果两块电池中的任何一块在使用过程中电
量耗竭,则座杆会保持在当前位置,直至电
池已更换。
在使用过程中,如果
AXS
致动器电池比座杆
电池更早耗竭,则座杆
AXS 按钮可用于升高
或降低座杆。
注意
如果压缩后的座杆不会弹回至完全伸展位
置,请勿强行拉动座杆头。

Chat with your RockShox Reverb AXS manual using AI

Get instant AI answers from your RockShox Reverb AXS manual

Ask anything about the RockShox Reverb AXS. Answers come from this manual, with the pages they are based on.

Reverb AXS Maintenance Schedule

Before and after each use
Check battery levels

Check battery levels before and after each use. Charge or replace batteries as needed.

Show in the manual (page 13)
Periodically
Clean the seatpost

Wipe off dirt with a damp cloth. Clean components with soap and water only. Rinse thoroughly and allow to dry.

Show in the manual (page 37)
M: QW-35-FL

Ask a Question

0/1000

Do you recommend Reverb AXS?

Yes No

Frequently Asked Questions

A

Yes. The guidance stresses that you must read and understand the included safety instructions before proceeding. Incorrect installation can be extremely dangerous and may lead to severe or fatal injuries. If you have questions, consult a qualified bicycle mechanic. The manual also indicates safety instructions are available online via SRAM.

Is this answer helpful?

A

Clean the inside of the seat tube and remove burrs from the frame edges. Apply friction paste to the inside seat tube and the seatpost contact surface, and do not apply grease. Insert the seatpost at least 80 mm or to your frame manufacturers minimum insertion, whichever is greater. Tighten the seat collar to the lower of 6.7 N.m or your frame specification.

Is this answer helpful?

A

Pairing must happen before use. Start the pairing session at the seatpost by pressing and holding the seatpost AXS button until the green LED blinks slowly, then release. After timing out after 30 seconds of inactivity, continue on the controller by pressing and holding the controller AXS button until the green LED blinks quickly, then release. Confirm pairing by pressing the controller paddle. Repeat if the seatpost does not respond.

Is this answer helpful?

A

You should check charge levels before and after each use. If a battery depletes during use, the seatpost stays in its current position until the battery is replaced. If the controller battery depletes before the seatpost battery, the seatpost AXS button can raise or lower the seatpost. The LED can show near depletion (blinking red) and indicates the battery safety shutoff has activated.

Is this answer helpful?

A

When you press the controller paddle, controller AXS button, or the seatpost AXS button, the LED illuminates. The LED color indicates battery charge level. During use, if the seatpost does not respond to controller input, it can indicate the SRAM battery is near depletion (blinking red) and the safety shutoff has been activated.

Is this answer helpful?

A

No. The guidance explicitly says you must not attempt to adjust air pressure using the air valve on the seatpost. Any change to the factory air pressure setting can render the seatpost inoperable, requiring full service.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • Wireless AXS actuation makes it easy to raise or lower the seatpost with controller paddle and seatpost AXS button.
  • LED indicator communicates battery charge level and low-power behavior during rides.
  • Safety shutoff helps maintain predictable operation when power is near depletion.
  • AXS app supports account setup, customization, notifications, and access to service intervals.
  • Designed compatibility across seat tube internal diameters and common saddle rail types.
VS

Disadvantages

  • Strict installation requirements (friction paste, minimum insertion depth, torque limits) must be followed to avoid issues.
  • Battery handling and charging require care, including keeping hands and gloves clean.
  • Pairing can be time-sensitive and must be repeated when components are replaced, added, or removed.
  • Air pressure should not be adjusted using the seatpost air valve, or the post may become inoperable.
  • SRAM components typically need specialized tools and are best installed by a qualified mechanic.
M: OA-GPT-54-NAN

Product Specification

Type

Dropper seatpost

Colors

black

Operation

Remote control

Transmission

Wireless

Cable routing

wireless

Setback

0 in

M: GO-GEM-FL-25

Product Description

RockShox Reverb AXS - Smooth, Wireless Seatpost Control

The RockShox Reverb AXS brings electronic, on-the-move suspension tuning to your ride by combining a dropper seatpost with AXS wireless control. Instead of relying on cables or manual levers, you command the seat height at the push of the controller paddle or the AXS button on the seatpost, letting you fine-tune your position for climbs, descents, and technical sections.

This guide-style overview draws on the RockShox Reverb AXS Manual to highlight what matters most for everyday use and installation. After pairing, the system lets the controller send actuation commands to the seatpost. During operation, a built-in LED indicator helps you understand battery status, and if battery power approaches depletion, the system activates a safety shutoff so the seatpost behavior remains predictable.

Setup also includes the SRAM AXS app, which you can download after your components are installed and paired. The app supports account creation, component management, and customization, plus notifications for product features and firmware updates. It also gives access to product data and recommended service intervals, which is especially helpful if you ride frequently or in harsh conditions.

Proper installation is critical. The seat tube must be cleaned before fitment, friction paste should be applied to the inside of the seat tube and the contact surface of the seatpost (do not use grease), and the seatpost must be inserted at least 80 mm or to your frame manufacturers minimum insertion requirement, whichever is greater. Torque matters too: the seat collar should be tightened to the lower of 6.7 N.m or your frame specification.

Notes on safe operation and battery handling are emphasized as well. Do not attempt to adjust factory air pressure using the seatpost air valve, and keep battery handling clean to avoid damage. If your controller battery depletes before the seatpost battery, the seatpost AXS button can still raise or lower the post, with instructions that guide how to lock the desired position.

Key takeaways

  • Electronic control lets you raise or lower the seatpost instantly with controller paddle or seatpost AXS button.
  • LED charging feedback and safety shutoff help manage low-power situations.
  • Friction paste, correct insertion depth, and torque specs are essential for safe, reliable operation.
  • Pairing establishes controller-to-seatpost communication and must be redone when components change.

Pros and cons notes

  • Expect a more hands-off ride feel, but plan for careful installation and battery upkeep.
M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly