Manual.ly Logo

PeakTech 3435 Manual

0.0 · 0 Ratings

PDF manual · 46 Pages

English

M: OA-GPT-54-NAN
page

/ 46

Loading...
293329c3019ef350da901c15f9647e8c2c85 page 17
1. Safety precautions
This product complies with the requirements of the following European Community Directives:
2004/108/EC (Electromagnetic Compatibility) and 2006/95/EC (Low Voltage) as amended by
2004/22/EC (CE-Marking). Overvoltage category III 300 V; pollution degree 2.
CAT I: For signal level, telecommunication, electronic with small transient over voltage
CAT II: For local level, appliances, main wall outlets, portable equipment
CAT III: Supplied from a cable under earth; fixed installed switches, automatic cut-off or main
plugs.
CAT IV: Units and installations, which are supplied over aerial line, which are stand in a risk of
persuade of a lightning, i.e. main-switches on current input, overvoltage-diverter, current
use counter.
To ensure safe operation of the equipment and eliminate the danger of serious injury due to short-
circuits (arcing), the following safety precautions must be observed.
* Do not use this instrument for high-energy industrial installation measurement.
* Do not exceed the maximum permissible input ratings (danger of serious injury and/or
destruction of the equipment).
* The meter is designed to withstand the stated max voltages. If it is not possible to exclude
without that impulses, transients, disturbance or for other reasons, these voltages are
exceeded a suitable prescale (10:1) must be used.
* Replace a defective fuse only with a fuse of the original rating. Never short-circuit fuse or fuse
holding.
* Disconnect test leads or probe from the measuring circuit before switching modes or functions.
* Never touch the tips of the test leads or probe.
* Do not conduct voltage measurements with the test leads connected to the µA/mA- and COM-
terminal of the equipment.
* To avoid electric shock, disconnect power to the unit under test and discharge all capacitors
before taking any resistance measurements.
* Do not conduct current measurements with the leads connected to the V-terminals of the
equipment.
* Check test leads and probes for faulty insulation or bare wires before connection to the
equipment.
* Comply with the warning labels and other info on the equipment.
* To avoid electric shock, do not operate this product in wet or damp conditions. Conduct
measuring works only in dry clothing and rubber shoes, i. e. on isolating mats.
* Do not subject the equipment to shocks or strong vibrations.
* Keep hot soldering irons or guns away from the equipment.
* Do not subject the equipment to direct sunlight or extreme temperatures, humidity or
dampness.
* Do not operate the equipment near strong magnetic fields (motors, transformers etc.).
* Allow the equipment to stabilize at room temperature before taking up measurement (important
for exact measurements).
* Do not input values over the maximum range of each measurement to avoid damages of the
meter.
* Do not turn the rotary function switch during voltage or current measurement, otherwise the
meter could be damaged.
* Use caution when working with voltages above 35V DC or 25V AC. These Voltages pose
shock hazard.
* Replace the battery as soon as the battery indicator “BAT” appears. With a low battery, the
meter might produce false reading that can lead to electric shock and personal injury.
-22-

Chat with your PeakTech 3435 manual using AI

Get instant AI answers from your PeakTech 3435 manual

Ask anything about the PeakTech 3435. Answers come from this manual, with the pages they are based on.

3435 Maintenance Schedule

Remind me when maintenance is due
Yearly
Calibrate the unit

It is recommended to repeat the factory calibration after one year of operation.

Show in the manual (page 45)
When low battery indicator appears
Replace the battery

Replace the 9V block battery immediately when the BAT symbol appears to ensure accurate measurements and prevent electric shock.

Show in the manual (page 21)
Regularly
Clean the housing

Wipe the cabinet with a damp, soft cloth and mild detergent. Do not use abrasives or solvents and ensure no liquid enters the device.

Show in the manual (page 21)

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: QW-35-FL

Ask a Question

0/1000

Do you recommend 3435?

Yes No

Frequently Asked Questions

A

It is used to trace cables, locate line breaks and short circuits, identify switches and fuses, and follow pipes or conductors in walls, floors, ceilings, and soil.

Is this answer helpful?

A

Yes. It can work on live and de-energized conductors, but live measurements must follow all safety rules and voltage limits.

Is this answer helpful?

A

Tracing depth depends on the material and method. In single-pole use it can reach up to about 2 meters, while two-pole searches are usually shallower.

Is this answer helpful?

A

Yes. The receiver includes an NCV mode that detects voltage without direct electrical contact and gives visual and audible alerts.

Is this answer helpful?

A

Yes. The system supports up to seven transmitter codes, which helps sort and identify different lines when several transmitters are used.

Is this answer helpful?

A

It is mainly aimed at trained users, electricians, and maintenance staff. The device offers powerful functions, but correct setup and safety knowledge are important.

Is this answer helpful?

A

Check the battery level, fuse condition, lead connections, grounding quality, and whether the circuit is prepared correctly for the chosen measuring mode.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • Tracks live and de-energized conductors, pipes, and grounding paths.
  • Dual-unit system supports precise fault finding and circuit identification.
  • Backlit display, bar graph, NCV mode, and LED improve usability.
  • Up to seven transmitter codes help organize multiple lines and tasks.
VS

Disadvantages

  • Requires careful setup and strict safety awareness for reliable results.
  • Tracing depth can drop in dense, shielded, or damp materials.
  • Best performance often depends on correct grounding and circuit preparation.
  • Some advanced methods may need an additional transmitter or extra accessories.
M: OA-GPT-54-NAN

Product Specification

Suitable for

live wires, non-live wires

Measuring range

max. 7.87 in

Power supply

Battery operation (1x 9V block battery)

Weight

0.40 lb

Scope of delivery

Case, Battery

M: OA-GPT-54-NAN

Product Description

PeakTech 3435 Locator Manual: A Practical Cable Detector for Demanding Jobs

The PeakTech 3435 Locator is built for technicians who need more than a basic cable tracer. It combines a transmitter and receiver into a versatile locating system designed to follow live and de-energized conductors, identify interruptions, and support everyday troubleshooting in walls, ceilings, floors, pipes, and even soil. For renovation work, installation checks, or fault finding in complex electrical systems, it offers a focused and professional approach.

What makes this device stand out is its flexibility. The transmitter can work in single-pole or two-pole applications, while the receiver offers automatic, manual, and selective measuring behavior. That means the user can adapt the search strategy to the material, the wiring layout, and the level of precision needed. With up to seven transmitter codes available, multiple signals can be separated and assigned clearly, which is especially helpful when sorting circuits or identifying lines in busy installations.

The receiver is also designed for usability. A backlit LCD, bar graph, acoustic signaling, and a built-in LED help make work easier in dim spaces and tight panels. The NCV function adds another layer of convenience by allowing non-contact voltage detection, while the high sensitivity of the system supports tracing at distances of up to two meters in favorable conditions. In practice, that opens the door to locating switches, fuses, breaks, short circuits, pipe routes, and grounding paths with one tool.

Safety is clearly central to the design. The device is rated for CAT III 300 V, includes detailed operating limits, and emphasizes proper handling of test leads, batteries, and fuse replacement. That focus on controlled use makes it suitable for trained users who need reliable results without sacrificing caution. It is best viewed as a specialized locating instrument for indoor professional or serious trade use rather than a general-purpose tester.

Overall, the PeakTech 3435 Locator is a strong choice for users who want one system for cable tracking, circuit sorting, and fault localization. It blends practical indicators, adjustable transmission levels, and broad application support into a compact tool that can save time during diagnostics and installation work.

Notes

  • Best for indoor electrical and pipe-tracking tasks
  • Adjustable signal levels help tailor the search depth
  • A second transmitter can improve fault localization
  • Always follow voltage and safety limits before testing
M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly