Manual.ly Logo

Omnitronic KM-11.A Manual

0.0 · 0 Ratings

PDF manual · 20 Pages

English

M: QW-35-FL
page

/ 20

Loading...
f83c60989b358877c353b27b39f8309f8ce8 page d
13
This device has left our premises in absolutely perfect condition. In order to maintain this condition and to
ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning
notes written in this user manual.
Damages caused by the disregard of this user manual are not subject to warranty. The dealer will not
accept liability for any resulting defects or problems.
Unpacking
Please make sure that there are no obvious transport
damages. Should you notice any damages on the
connection panel or on the casing, do not take the
speaker system into operation and immediately consult
your local dealer.
Protection Class
This device falls under protection class I. The power
plug must only be plugged into a protection class I
outlet. The voltage and frequency must exactly be the
same as stated on the device. Wrong voltages or power
outlets can lead to the destruction of the device and to
mortal electrical shock.
Power Cord
Always plug in the power plug least. The power plug
must always be inserted without force. Make sure that
the plug is tightly connected with the outlet. Never let
the power cord come into contact with other cables!
Handle the power cord and all connections with the
mains with particular caution! Never touch them with
wet hands, as this could lead to mortal electrical shock.
Never modify, bend, strain mechanically, put pressure
on, pull or heat up the power cord. Never operate next
to sources of heat or cold. Disregard can lead to power
cord damages, fire or mortal electrical shock. The cable
insert or the female part in the device must never be
strained. There must always be sufficient cable to the
device. Otherwise, the cable may be damaged which
may lead to mortal damage. Make sure that the power
cord is never crimped or damaged by sharp edges.
Check the device and the power cord from time to time.
If extension cords are used, make sure that the core
diameter is sufficient for the required power
consumption of the device. All warnings concerning the
power cords are also valid for possible extension cords.
Always disconnect from the mains, when the device is
not in use or before cleaning it. Only handle the power
cord by the plug. Never pull out the plug by tugging the
power cord. Otherwise, the cable or plug can be
damaged leading to mortal electrical shock. If the power
plug or the power switch is not accessible, the device
must be disconnected via the mains.
If the power plug or the device is dusty, the device must
be taken out of operation, disconnected and then be
cleaned with a dry cloth. Dust can reduce the insulation
which may lead to mortal electrical shock. More severe
dirt in and at the device should only be removed by a
specialist.
Liquids
There must never enter any liquid into power outlets,
extension cords or any holes in the housing of the
device. If you suppose that also a minimal amount of
liquid may have entered the device, it must immediately
be disconnected. This is also valid, if the device was
exposed to high humidity. Also if the device is still
running, the device must be checked by a specialist if
the liquid has reduced any insulation. Reduced
insulation can cause mortal electrical shock.
Foreign Objects
There must never be any objects entering into the
device. This is especially valid for metal parts. If any
metal parts like staples or coarse metal chips enter into
the device, the device must be taken out of operation
and disconnected immediately. Malfunction or short-
circuits caused by metal parts may cause mortal
injuries.
Secure Setup
Please note that speaker systems could move due to
bass beats and vibrations. Furthermore, unintended
pushes from DJs, musicians or the audience present
further risk. This is why the speaker system must
always be secured against moving or the respective
area has to be blocked.
Prior to Switching on
Before the speaker system is switched on all faders and
volume controls have to be set to zero or minimum
position.
Children and Amateurs
Keep away children and amateurs!
Maintenance and Service
There are no serviceable parts inside the speaker
system. Maintenance and service operations are only to
be carried out by authorized dealers!
WARNING!
Speaker systems must only be operated by trained persons. Danger of Life due to crashing
speaker systems or hearing loss due to excessive sound pressure levels! The different local
conditions have to be considered in terms of safety rules.

Chat with your Omnitronic KM-11.A manual using AI

Get instant AI answers from your Omnitronic KM-11.A manual

Ask anything about the Omnitronic KM-11.A. Answers come from this manual, with the pages they are based on.

KM-11.A Maintenance Schedule

Frequent
Clean the speaker system housing

Use a soft lint-free and moistened cloth. Never use alcohol or solvents. Disconnect from mains before cleaning.

Show in the manual (page 18)
Regularly
Inspect device and power cord for damage

Check the device and the power cord from time to time for signs of wear, crimping, or sharp edge damage.

Show in the manual (page 13)
As needed
Replace blown fuse

Only replace with a fuse of same type and rating after disconnecting from mains. Open holder, swap fuse, close.

Show in the manual (page 19)
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend KM-11.A?

Yes No

Frequently Asked Questions

A

The monitors support 115/230 V AC, 50/60 Hz power supply. You can adjust the voltage selector switch to match your local mains voltage. Ensure the connection meets the voltage and frequency requirements exactly to prevent damage.

Is this answer helpful?

A

Use the parallel output jack labeled LINK. Connect this output to the line input of the second monitor. This allows audio daisy-chaining so both units receive the same signal from a single source without requiring extra cables from the mixer.

Is this answer helpful?

A

Yes, but you must keep them far enough away to prevent feedback. If high-pitch squeals occur, adjust positioning or use the low cut filter. Avoid holding mics directly in front of the speaker grille during operation.

Is this answer helpful?

A

Use a soft, lint-free cloth dampened with water. Never use alcohol, solvents, or harsh detergents. Ensure the unit is disconnected from the mains before cleaning to avoid electrical hazards or component damage.

Is this answer helpful?

A

The 112A model offers a frequency range of 50-20000 Hz. This wide range handles deep bass notes and high highs effectively. It uses a 12-inch woofer paired with a 1.35-inch tweeter for the full range.

Is this answer helpful?

A

Yes, there is a Ground Lift selector switch. If you experience humming noises without a signal, engage this switch to separate signal ground and housing ground. This breaks any ground loops that cause unwanted interference noises.

Is this answer helpful?

A

Yes, it features a threaded flange on the bottom for standard PA stand mounting. Ensure the stand is stable and rated for the weight. Do not exceed the maximum point load of the mounting surface to prevent accidents.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • High power output suitable for live events with Class D/AB amplifiers.
  • Coaxial design ensures clear and consistent sound dispersion across the frequency range.
  • Multiple equalizer presets for different positions like Monitor or FOH.
  • Dual limiter and overload protection circuits safeguard speakers from damage.
  • Modular system allows linking multiple units via parallel outputs easily.
VS

Disadvantages

  • Large cabinets can be heavy and difficult to transport manually alone.
  • Requires careful placement to avoid feedback issues with microphones.
  • Sensitivity to moisture and weather exposure limits outdoor use without protection.
  • Ground lift switch sometimes requires troubleshooting if electrical hum persists.
  • Fixed cabinet dimensions may not fit into tight stage spaces.
M: QW-35-FL

Product Specification

Type

2-Way

Tweeter

1x 1.35"

Amplification

Active

Impedance

30 Ohms

M: QW-35-FL

Product Description

Unlocking Professional Sound with the Omnitronic KM-11.A Unit

Finding reliable audio monitoring on stage is crucial for performers and bands. The Omnitronic KM-11.A Unit series delivers exactly that with robust design and clear sound projection. These active coaxial stage monitors are built specifically for live performances and playback applications in various venues. Whether you need a compact solution for small gigs or high volume power for larger stages, the series offers distinct options to suit different stage needs perfectly without compromise. It is a top choice for audio engineers.

Performance is the core strength of these high-quality monitors. Equipped with Class D/AB bi-amp power amplifiers, the units ensure efficient power delivery without excessive heat generation during long sets. Users can choose between different driver configurations depending on the venue size. The smaller models feature a 10-inch bass driver paired with a 1.35-inch high frequency driver for crisp highs. Larger options step up to 12-inch or 15-inch woofers for deeper bass response and higher sound pressure levels needed for rock bands. Maximum power ratings vary significantly, allowing flexibility for small clubs or large stages while maintaining audio fidelity. The Class D technology ensures efficiency.

Control versatility sets these systems apart from standard passive alternatives found in many venues. A dedicated Monitor or FOH switch changes the equalizer characteristics instantly to match the acoustic situation perfectly. This saves time during sound checks. This allows the same box to serve as a stage monitor with attenuated bass for the musician or as a front-of-house speaker directed at the audience. The signal path includes a balanced line input via XLR or jack and an identical parallel output to daisy-chain additional units easily for wider coverage. Protection circuits like dual limiters safeguard the drivers from overloads while the sturdy MDF housing with impact-resistant steel grille resists physical damage during transport and set-up.

Installation requires strict attention to safety and environmental limits for optimal longevity. The unit features a threaded flange for standard PA stand mounting but must always be placed on a stable surface to prevent tipping due to heavy bass vibrations. Feedback remains a common issue so proper distance from microphones is vital to maintain clean audio during live vocal sets. Regular maintenance involves cleaning with a soft cloth and ensuring the power cable remains undamaged and not pinched during use. Maintain temperature within specified safe operating ranges. With proper handling and ventilation, these monitors provide years of reliable service in demanding environments.

M: QW-35-FL

© Copyright 2026 Manual.ly