Manual.ly Logo

Monacor PA-806DAP Manual

0.0 · 0 Ratings

PDF manual · 16 Pages

English

M: QW-35-FL
page

/ 16

Loading...
a42baf5c1640a9c5646fa19242bb003d5673 page c
12
English
MICRO
SD
ON
PROT
CLIP
0dB
-
10
-
30
PA - 812DAP
0 10
CH 1
MODE/ PLAY FOLDER R PT/SC AN
0 10
CH 2
0 10
CH 3
0 10
CH 4
0 10
CH 5
0 10
TEL
0 10
BASS
0 10
TREBLE
0 10
MASTER
POWER
PRE/V
NE X T/V+
USB
0 10−10 +10 −10 +1 00 10
2) The output MOH OUTPUT (music on hold) is
able to provide, for example, music on hold for
a telephone system. The mixed signal is also
available at this output. The control MASTER
will not have any effect on the volume.
3.3 Power supply
For power supply, either connect the jack
“230 V~” to a mains socket (230 V/ 50 Hz) using
the mains cable provided or, for mobile applica-
tions for example, connect the terminals “24 V⎓”
to a 24 VDC voltage source.
4 Operation
1)
Before first-time operation, make sure that the
initial volume is not too high: Set the control
MASTER for the total volume approximately to
the position “9 o’clock”. Then switch on the
amplifier with the switch POWER. The green
power LED ON will light up.
2) Use the controls CH 1– 5 and TEL to mix the
signals of the audio sources or to fade them
in or out. Set the controls of the inputs which
are not used to “0”.
3)
Adjust the total volume with the control
MASTER. The LEDs “−30, −10, 0 dB, CLIP”
will indicate the output level. To prevent dis-
tortions, only turn up the control MASTER to
such a level that the red LED “CLIP” will not
light up.
4) Use the controls BASS and TREBLE to adjust
the sound.
5) If the LED “PROT” lights up, the amplifier is
overheated or overloaded or has a short circuit
at one of the speaker outputs. In this case,
switch off the amplifier and have the fault
eliminated.
When a storage medium is inserted in the music
module, the replay will automatically start after
the amplifier has been switched on. When two
storage media are used, the memory card will
take precedence. When no storage medium is
inserted, the operating mode most recently used
(Bluetooth receiver, digital radio, FM radio) will
be resumed (chapter 4.2).
4.1 Infrared remote control
8 97
5 64
2 31
0
RPT U/SD
SCN
EQ VOL− VOL+
Mode
Power supply of the re-
mote control for the
music module is provided
by means of a 3 V button
cell. If the remote control
is supplied with the bat-
tery inserted, remove the
protective film (to protect
the battery against dis-
charge) from the battery
support: The remote con-
trol will then be ready for
operation. When pressing
a button on the remote
control, always point the
remote control at the IR
sensor above the USB port.
Make sure that there are no obstacles between
the IR sensor and the remote control.
If the remote control is not used for a longer
period of time, remove the battery as a precau-
tion. It may leak and damage the remote control.
4.1.1 Replacing the battery
1)
Push the latch of the battery holder to the
right (first arrow in the figure below) and re-
move the holder (second arrow).
1. 2.
2)
Remove the old battery and insert the new
battery (3 V button cell, type CR 2025) into the
holder with the positive pole facing upwards.
3) Push the holder back into the remote control.

Chat with your Monacor PA-806DAP manual using AI

Get instant AI answers from your Monacor PA-806DAP manual

Ask anything about the Monacor PA-806DAP. Answers come from this manual, with the pages they are based on.

PA-806DAP Maintenance Schedule

As needed
Clean the product with a dry, soft cloth

For cleaning the product only use a dry, soft cloth; never use water or chemicals.

Show in the manual (page 10)
When not used for long periods
Remove battery from remote control

If the remote control is not used for a longer period of time, remove the battery as a precaution against leakage damage.

Show in the manual (page 12)
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend PA-806DAP?

Yes No

Frequently Asked Questions

A

It supports both 230-volt AC operation for mains power and 24-volt DC input suitable for mobile applications or backup power sources.

Is this answer helpful?

A

Yes, it has integrated Bluetooth 4.2 receiver to stream music from smartphones and tablets wirelessly to the speakers.

Is this answer helpful?

A

You can connect up to three microphones. The input priority settings allow you to choose which microphone channel takes precedence.

Is this answer helpful?

A

Yes, the telephone input prioritizes emergency announcements and mutes all other channels when active for safety purposes.

Is this answer helpful?

A

It supports speakers ranging from 4 to 16 ohms as well as 70V and 100V constant voltage lines for commercial installations.

Is this answer helpful?

A

Use a dry soft cloth. Never use water or chemicals on the housing to prevent electrical damage or safety hazards.

Is this answer helpful?

A

Yes, the built-in player reads MP3 and WAV files from Micro SD cards or USB flash drives automatically upon startup.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • 120-Watt power output handles large speaker loads for extensive coverage areas effectively
  • Dual voltage support allows 230V AC or 24V DC input compatibility for flexible installation
  • Integrated Bluetooth and DAB Plus radio for modern media access without extra hardware
  • Priority input for emergency telephone calls overrides all other channels during critical alerts
  • Infrared remote control provides convenient operation of the music module and functions
VS

Disadvantages

  • Phantom power limited to CH 1 only restricts mic choices for balanced setups
  • Overload protection cuts power if impedance is wrong requiring manual reset
  • Signal interruption occurs if only one insertion jack is used for processing gear
  • Stereo signals are converted to mono by the amplifier which may reduce fidelity
  • Compatible storage media cannot be guaranteed for all manufacturers or drivers
M: QW-35-FL

Product Specification

Type

Zone Mixer

Channels

1

Format

19" Rack (3HE)

Features

USB

M: QW-35-FL

Product Description

Monacor PA DAP Experience

The Monacor PA-812DAP stands out as a versatile mixing amplifier designed for professionals and specialists. Whether you are installing a public address system or managing audio for events, this device offers robust performance. It integrates seamlessly into existing setups while providing modern connectivity options that enhance user experience and functionality.

Versatile Audio Capabilities

One of the standout features is the ability to handle multiple audio sources simultaneously. You can connect up to three microphones for clear voice transmission with phantom power support on the primary channel. Additionally, four other audio sources can be mixed in, ranging from mobile devices playing Bluetooth tracks to digital radio frequencies and satellite options available. The built-in music module simplifies media playback significantly. Users appreciate the support for Micro SD memory cards and USB storage devices, allowing easy access to playlists without additional hardware. This capability ensures that background music or announcements are always ready for listeners throughout the venue reliably.

Flexible Power and Installation

This unit is not limited to standard wall power. It supports 230-volt operation for permanent installations. The power consumption is 250 VA for AC input. For mobile scenarios, the 24-volt DC input option ensures reliability where grid power is unavailable. This flexibility makes it suitable for both indoor commercial spaces and mobile applications. Safety is paramount during setup. Users must ensure proper ventilation around the device to prevent overheating. Protective caps should remain on terminals when not in use to avoid accidental contact with electrical components. Proper grounding ensures consistent performance over time.

Safety and Compliance

Handling high voltage requires caution. The unit carries the CE mark, indicating compliance with European directives during manufacturing and assembly. Always follow the guidelines regarding moisture and temperature. Operating the unit within the specified range of 0 to 40 degrees Celsius ensures longevity and stable performance. The integrated protection circuitry monitors load conditions to prevent damage during high demand periods. If the protection LED lights up, the system has detected a fault or overload condition requiring immediate attention. Ignoring warnings can result in equipment failure or safety hazards. Regular maintenance checks are recommended to ensure long-term reliability.

Connectivity and Control

The interface includes an infrared remote control for convenient operation of the music module. Bass and treble controls allow for precise sound shaping to suit the environment. Emergency announcements can be prioritized using the telephone input, ensuring critical messages cut through music. The speaker outputs support both high voltage lines and low impedance speakers. Detailed technical specifications help technicians configure the system correctly. Referencing the Monacor PA DAP Manual helps optimize installation procedures. Bluetooth pairing uses a standard PIN for secure access and easy connection setup.

M: QW-35-FL

© Copyright 2026 Manual.ly