Manual.ly Logo

Mafell SKS 130 Manual

0.0 · 0 Ratings

PDF manual · 82 Pages

English

M: QW-35-FL
page

/ 82

Loading...
d4e92ca104c0ebc5a9dd6a120d1e2c8d289a page 15
-21-
MAFELL machines are designed to be low in
maintenance.
The ball bearings used are greased for life. When the
machine has been in operation for a longer period of
time, we recommend to hand the machine in at an
authorised MAFELL customer service shop for
inspection.
Only use our special grease, order No. 049040 (1 kg
tin) for all greasing points.
6.1 Mortising chains
The mortising chain used on the machine should be
cleaned and lubricated in a low viscosity oil bath after
two hours of operation. To do so, dismantle the
mortising chain (see chapter 4.3).
Replace the blunt mortising chains or have them
reground at a MAFELL customer service station or by
a suitable sharpening service.
6.2 Storage
If the machine is not used for a longer period of time,
it has to be carefully cleaned. Spray bright metal parts
with a rust inhibitor.
7 Troubleshooting
Danger
Determining the causes for existing defects and eliminating these always
requires increased attention and caution. Pull the mains plug beforehand!
Some of the most frequent defects and their causes are listed in the following chart. In case of other defects,
contact your dealer or the MAFELL customer service.
Defect Cause Elimination
No mains voltage Check power supply
Mains fuse defective Replace fuse
Machine cannot be switched on
Carbon brushes worn Take the machine to a MAFELL
customer service shop
Mains failure Check mains back-up fuses
Machine overloaded Reduce feed speed
Machine stops while mortising is in
process
Unfavourable residue mortising
(see Fig. 6)
Relocate the machine and mortise
the residue with a chain
Wood is too dampChip ejection blocked
Extended mortising without
exhaustion
Connect to an external extraction,
e.g. portable dust extractor
8 Exploded drawing and spare parts list
The corresponding information in respect of spare parts can be found on our homepage: www.mafell.com

Chat with your Mafell SKS 130 manual using AI

Get instant AI answers from your Mafell SKS 130 manual

Ask anything about the Mafell SKS 130. Answers come from this manual, with the pages they are based on.

SKS 130 Maintenance Schedule

Every 2 operating hours
Clean and lubricate the mortising chain

After two hours of operation, clean the mortising chain and lubricate it in a low viscosity oil bath. Dismantle the chain to perform this task.

Show in the manual (page 21)
As needed
Sharpen or replace blunt mortising chains

Replace blunt mortising chains or have them reground at a MAFELL customer service station or by a suitable sharpening service.

Show in the manual (page 21)
Before each use
Check chain tension

Before switching on, check whether the mortising chains are properly tensioned. Correct tension is reached when chains can be lifted approx. 6 mm in the center.

Show in the manual (page 18)
Regularly
Clean adjusting devices and guides

Regularly clean the machine, especially the adjusting devices and guides, as this constitutes an important safety factor.

Show in the manual (page 18)
After long storage
Apply rust inhibitor before storage

If the machine is not used for a longer period, carefully clean it and spray bright metal parts with a rust inhibitor.

Show in the manual (page 21)
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend SKS 130?

Yes No

Frequently Asked Questions

A

The machine is designed for mains connections of 230 V~, 50 Hz or 110 V~, 50 Hz. Ensure the supply voltage matches the rating plate before connecting the power source to avoid motor damage.

Is this answer helpful?

A

No, it is exclusively intended for mortising doors made of solid wood or common derived timber products. Using it on metal doors is prohibited and will damage the chains and void the warranty.

Is this answer helpful?

A

The mortising chain used on the machine should be cleaned and lubricated in a low viscosity oil bath after two hours of operation to ensure smooth cutting and longevity.

Is this answer helpful?

A

The mortising depth is continuously variable between 0 and 145 millimeters, allowing customization for different lock pocket sizes and depths as required by the installation specifications.

Is this answer helpful?

A

Yes, chip extraction is mandatory for health safety. The air velocity must be at least 20 m/s. Wood dust impairs visibility and is injurious to health without proper suction.

Is this answer helpful?

A

Always wear ear protectors and a dust mask during work. Never work without prescribed protection devices or modify the machine, which could impair safety and risk severe injury.

Is this answer helpful?

A

The correct chain tension is reached when the mortising chains can be lifted by approximately 6 mm in the center of the guide rails. Check this before switching the machine on.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Powerful 1600W motor ensures efficient cutting through solid wood and timber products without stalling.
  • Adjustable depth up to 145 mm offers versatility for various door lock casing requirements and sizes.
  • Integrated safety devices like gas spring and chain guard minimize risk of accidental injury during operation.
  • Lightweight design at 10.6 kg reduces operator fatigue during extended use on construction sites.
  • Original spare parts and tools are included for immediate setup and future maintenance needs.
VS

Disadvantages

  • High noise level of 108 dB requires mandatory ear protection to prevent hearing damage over time.
  • Strict prohibition on using metal doors limits application only to solid wood and standard materials.
  • Chains must be cleaned and oiled every two hours to maintain performance and prevent premature wear.
  • Vibration level of 4.0 m/s2 may cause hand arm fatigue if working for long uninterrupted periods.
  • Requires connection to external dust extraction to meet air velocity standards for health safety.
M: QW-35-FL

Product Description

The Essential Guide to the Mafell SKS Chain Mortiser

Introduction to Professional Mortising

The Mafell SKS Chain Mortiser Manual provides comprehensive instructions for operating a high-end woodworking tool designed specifically for door lock mortising tasks. This equipment is essential for carpenters and door installation professionals who require accuracy when cutting lock casings into solid wood or timber products. The text covers everything from initial setup to routine maintenance, ensuring every user can operate the machine safely and effectively. Whether you are working in a workshop or on-site, understanding the operational limits is crucial for job success. It is vital to read all safety notes before starting work.

Technical Specifications and Features

This unit comes equipped with a powerful 1600-watt universal motor that handles continuous operation without overheating under nominal load. The idle speed reaches 5770 rpm, allowing for quick and precise cutting of hardwoods. The maximum mortising depth is adjustable up to 145 millimeters, providing significant versatility for different lock types. Weighing only 10.6 kilograms without the power cable, the machine remains portable for various job sites. It works with 230 volts or 110 volts depending on regional power standards listed in the text.

Safety Protocols to Follow

Safety cannot be compromised when using chainsaw-like mechanisms for mortising. The device features a chain guard, protective cover, and a base plate with a protective cam. Users must always wear ear protection because noise levels reach 108 decibels during machining. Wood dust emission is also a health risk, so connecting to a chip extraction system with at least 20 meters per second air velocity is mandatory. Never attempt to mortise metal doors as this damages the chains and voids safety guarantees.

Operational Setup and Adjustment

Setting up the machine requires attention to detail regarding positioning on the door leaf. Guide rails ensure straight cuts while the mortising chains are tensioned correctly. Proper tension means the chains can be lifted approximately 6 millimeters in the center of the guide rails. When adjusting the mortising depth, use the scale on the depth indicator to set the precise cutting range. Positioning differs for doors with or without rebates, requiring specific alignment marks on the protective cover.

Maintenance and Troubleshooting

Longevity depends on regular care and adherence to service schedules. The mortising chains should be cleaned and lubricated in an oil bath after every two hours of active use. If chains become blunt, they must be replaced or professionally sharpened by Mafell service centers. Troubleshooting sections address common issues like motor overload or chain jamming. Always pull the mains plug before performing any service work to prevent accidental startup. Using original spare parts is required to maintain warranty validity.

Final Thoughts on Usage

Mastering this equipment enhances productivity and quality in door construction projects. The text emphasizes securing the workpiece against slipping or overturning during operation. Operators must hold the machine with both hands while mortising to maintain control and stability. Avoid reaching under or to the side of the workpiece while the chains are moving. Adhering to these guidelines ensures a safe working environment and protects the machine from unnecessary wear and tear caused by misuse. This thorough understanding allows for optimal performance in woodworking scenarios. Ultimately, the right knowledge leads to better construction results.

M: QW-35-FL

© Copyright 2026 Manual.ly