Manual.ly Logo

Mafell SKS 130 Manual

0.0 · 0 Ratings

PDF manual · 82 Pages

English

M: QW-35-FL
page

/ 82

Loading...
d4e92ca104c0ebc5a9dd6a120d1e2c8d289a page 12
-18-
Instructions on operation:
- Provide for an unobstructed and slip-proof location
with sufficient lighting.
- Do not work on workpieces which are too small or
too large for the capability of the machine.
- Clamp mortising chains and guide rails
appropriately and keep in order. Repair defective
mortising chains professionally before reuse. Only
use sharp mortising chains!
- Only remove chain guard for tool change
purposes, immediately screw back on again
afterwards. Never work without chain guard!
- Never transport the chain mortiser with running
mortising chains! Avoid touching the ground with
the running mortising chain.
- The switch may not be wedged.
- Before switching on, check whether the mortising
chains are properly tensioned.
- Whenever possible secure the workpiece from
pivoting or sliding away, overturning and luffing up,
e.g by means of clamps.
- Only begin mortising the workpiece when the
mortising chains have reached their full speed.
- Examine the workpiece for foreign objects. Never
attempt to mortise into metal objects, such as
nails.
- Hold on tightly to the machine, already before
turning it on. The mortising chains must stand
unrestricted. Apply the machine for the mortising
operation with running mortising chains. Pay
attention to a secure footing.
- Never reach below or laterally onto the workpiece
during mortising (Risk of injury!).
- Always lead the connecting cable away from the
machine to the rear while mortising.
- Match the feed speed during mortising to the
material thickness. Mortising too quickly leads to
motor overload, to unclean mortises and to the
mortising chains blunting quickly.
- Only remove the machine from the workpiece if the
mortising chains have come to a standstill.
- Do not reach into the chip ejector and the
unprotected area of the mortising chain while the
machine is running.
- The wood dust arising during mortising impairs the
necessary view and is partly injurious to health. If
the machine is used for longer periods, it must
therefore be connected to a chip extractor, e.g. a
portable small extractor, if the work is not carried
out outdoors or in a sufficiently ventilated room.
The air velocity must be at least 20 m/s (65.6
ft/sec.).
Instructions on service and maintenance:
- Regularly cleaning the machine, especially the
adjusting devices and guides, constitutes an
important safety factor.
- Only original MAFELL spare parts and accessories
may be used. Otherwise the manufacturer will not
accept any warranty claims and cannot be held
liable.
4 Setting / Adjustment
4.1 Mains connection
Prior to commissioning make sure that the mains
voltage complies with the operating voltage stated on
the machine's rating plate.
4.2 Chip extraction
Connect the machine to a suitable external dust
extractor during all work generating a considerable
amount of dust. The air velocity must be at least 20
m/s (65.6 ft / sec.).
The inside diameter of hose connector 7 (Fig. 2) is 35
mm (1 3/8 in.).
4.3 Mortising chain change and chain wheel
change
Danger
Pull the power plug during all
service work.
Pay attention that the mortising chains to be clamped
have been well sharpened as this is a basic
requirement for correct mortising.
Proceed as follows for exchanging the mortising
chain:
Clamp the machine vertically onto a piece of
wood so that the machine cannot overturn.
Unfasten the screw 9 (Fig. 2) and remove the
chain guard 8.
Slacken the mortising chains 4 (Fig. 1) by
unfastening the two screws 3.

Chat with your Mafell SKS 130 manual using AI

Get instant AI answers from your Mafell SKS 130 manual

Ask anything about the Mafell SKS 130. Answers come from this manual, with the pages they are based on.

SKS 130 Maintenance Schedule

Every 2 operating hours
Clean and lubricate the mortising chain

After two hours of operation, clean the mortising chain and lubricate it in a low viscosity oil bath. Dismantle the chain to perform this task.

Show in the manual (page 21)
As needed
Sharpen or replace blunt mortising chains

Replace blunt mortising chains or have them reground at a MAFELL customer service station or by a suitable sharpening service.

Show in the manual (page 21)
Before each use
Check chain tension

Before switching on, check whether the mortising chains are properly tensioned. Correct tension is reached when chains can be lifted approx. 6 mm in the center.

Show in the manual (page 18)
Regularly
Clean adjusting devices and guides

Regularly clean the machine, especially the adjusting devices and guides, as this constitutes an important safety factor.

Show in the manual (page 18)
After long storage
Apply rust inhibitor before storage

If the machine is not used for a longer period, carefully clean it and spray bright metal parts with a rust inhibitor.

Show in the manual (page 21)
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend SKS 130?

Yes No

Frequently Asked Questions

A

The machine is designed for mains connections of 230 V~, 50 Hz or 110 V~, 50 Hz. Ensure the supply voltage matches the rating plate before connecting the power source to avoid motor damage.

Is this answer helpful?

A

No, it is exclusively intended for mortising doors made of solid wood or common derived timber products. Using it on metal doors is prohibited and will damage the chains and void the warranty.

Is this answer helpful?

A

The mortising chain used on the machine should be cleaned and lubricated in a low viscosity oil bath after two hours of operation to ensure smooth cutting and longevity.

Is this answer helpful?

A

The mortising depth is continuously variable between 0 and 145 millimeters, allowing customization for different lock pocket sizes and depths as required by the installation specifications.

Is this answer helpful?

A

Yes, chip extraction is mandatory for health safety. The air velocity must be at least 20 m/s. Wood dust impairs visibility and is injurious to health without proper suction.

Is this answer helpful?

A

Always wear ear protectors and a dust mask during work. Never work without prescribed protection devices or modify the machine, which could impair safety and risk severe injury.

Is this answer helpful?

A

The correct chain tension is reached when the mortising chains can be lifted by approximately 6 mm in the center of the guide rails. Check this before switching the machine on.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Powerful 1600W motor ensures efficient cutting through solid wood and timber products without stalling.
  • Adjustable depth up to 145 mm offers versatility for various door lock casing requirements and sizes.
  • Integrated safety devices like gas spring and chain guard minimize risk of accidental injury during operation.
  • Lightweight design at 10.6 kg reduces operator fatigue during extended use on construction sites.
  • Original spare parts and tools are included for immediate setup and future maintenance needs.
VS

Disadvantages

  • High noise level of 108 dB requires mandatory ear protection to prevent hearing damage over time.
  • Strict prohibition on using metal doors limits application only to solid wood and standard materials.
  • Chains must be cleaned and oiled every two hours to maintain performance and prevent premature wear.
  • Vibration level of 4.0 m/s2 may cause hand arm fatigue if working for long uninterrupted periods.
  • Requires connection to external dust extraction to meet air velocity standards for health safety.
M: QW-35-FL

Product Description

The Essential Guide to the Mafell SKS Chain Mortiser

Introduction to Professional Mortising

The Mafell SKS Chain Mortiser Manual provides comprehensive instructions for operating a high-end woodworking tool designed specifically for door lock mortising tasks. This equipment is essential for carpenters and door installation professionals who require accuracy when cutting lock casings into solid wood or timber products. The text covers everything from initial setup to routine maintenance, ensuring every user can operate the machine safely and effectively. Whether you are working in a workshop or on-site, understanding the operational limits is crucial for job success. It is vital to read all safety notes before starting work.

Technical Specifications and Features

This unit comes equipped with a powerful 1600-watt universal motor that handles continuous operation without overheating under nominal load. The idle speed reaches 5770 rpm, allowing for quick and precise cutting of hardwoods. The maximum mortising depth is adjustable up to 145 millimeters, providing significant versatility for different lock types. Weighing only 10.6 kilograms without the power cable, the machine remains portable for various job sites. It works with 230 volts or 110 volts depending on regional power standards listed in the text.

Safety Protocols to Follow

Safety cannot be compromised when using chainsaw-like mechanisms for mortising. The device features a chain guard, protective cover, and a base plate with a protective cam. Users must always wear ear protection because noise levels reach 108 decibels during machining. Wood dust emission is also a health risk, so connecting to a chip extraction system with at least 20 meters per second air velocity is mandatory. Never attempt to mortise metal doors as this damages the chains and voids safety guarantees.

Operational Setup and Adjustment

Setting up the machine requires attention to detail regarding positioning on the door leaf. Guide rails ensure straight cuts while the mortising chains are tensioned correctly. Proper tension means the chains can be lifted approximately 6 millimeters in the center of the guide rails. When adjusting the mortising depth, use the scale on the depth indicator to set the precise cutting range. Positioning differs for doors with or without rebates, requiring specific alignment marks on the protective cover.

Maintenance and Troubleshooting

Longevity depends on regular care and adherence to service schedules. The mortising chains should be cleaned and lubricated in an oil bath after every two hours of active use. If chains become blunt, they must be replaced or professionally sharpened by Mafell service centers. Troubleshooting sections address common issues like motor overload or chain jamming. Always pull the mains plug before performing any service work to prevent accidental startup. Using original spare parts is required to maintain warranty validity.

Final Thoughts on Usage

Mastering this equipment enhances productivity and quality in door construction projects. The text emphasizes securing the workpiece against slipping or overturning during operation. Operators must hold the machine with both hands while mortising to maintain control and stability. Avoid reaching under or to the side of the workpiece while the chains are moving. Adhering to these guidelines ensures a safe working environment and protects the machine from unnecessary wear and tear caused by misuse. This thorough understanding allows for optimal performance in woodworking scenarios. Ultimately, the right knowledge leads to better construction results.

M: QW-35-FL

© Copyright 2026 Manual.ly