Manual.ly Logo

Mafell KSS60cc Manual

0.0 · 0 Ratings

PDF manual · 114 Pages

English

M: claude-opus-5-5
page

/ 114

Loading...
57abd10387217cc4c890ee93b8115e625c53 page 1a
-26-
You can adjust the cutting width after releasing
the wing screws 20 (Fig. 2) by moving the limit
stop accordingly and afterwards retightening the
wing screws.
In addition, by simply turning it around (guide face for
the workpiece edge points upwards), the parallel stop
can also be used as double support to improve
guidance of the portable circular saw. Now the
machine can be guided along a guide that is fastened
on the workpiece.
5.10 Working with the roller edge guide
The roller edge guide serves to work parallel to an
already existing edge. The limit stop can be attached
to the left or right of the machine. The cutting range
on the right-hand side amounts to approx. 12 - 40 mm
(0.47 – 1.57 in.) and on the left-hand side to approx.
30 – 210 mm (1.18 – 8.27 in.).
You can adjust the cutting width after releasing
the wing screws 20 (Fig. 2) by moving the limit
stop accordingly and afterwards retightening the
wing screws.
6 Service and maintenance
Danger
Unplug the rechargeable battery for
all service work.
MAFELL machines are designed to be low in
maintenance.
The ball bearings used are greased for life. When the
machine has been in operation for a longer period of
time, we recommend to hand the machine in at an
authorised MAFELL customer service shop for
inspection.
Only use our special grease, order No. 049040 (1 kg
tin) for all greasing points.
6.1 Storage
If the machine is not used for a longer period of time,
it has to be carefully cleaned. Spray bright metal parts
with a rust inhibitor.
7 Troubleshooting
Danger
Determining the causes for existing defects and eliminating these always
requires increased attention and caution. Pull the mains plug beforehand!
Some of the most frequent defects and their causes are listed in the following chart. In case of other defects,
contact your dealer or the MAFELL customer service.
Defect
Cause
Elimination
Machine cannot be switched on
No mains voltage
Check power supply
Mains fuse defective
Replace fuse
Carbon brushes worn
Take the machine to a MAFELL
customer service shop
Machine stops while cutting is in
process
Mains failure
Check mains back-up fuses
Machine overloaded
Reduce feed speed

Chat with your Mafell KSS60cc manual using AI

Get instant AI answers from your Mafell KSS60cc manual

Ask anything about the Mafell KSS60cc. Answers come from this manual, with the pages they are based on.

KSS60cc Maintenance Schedule

Before each use
Check lower guard operation

Verify the lower guard closes properly and moves freely before every use. Do not operate if it sticks or fails to close instantly.

Show in the manual (page 22)
Regularly
Clean adjusting devices and guides

Regularly clean the machine, especially the adjusting devices and guides, as this is an important safety factor.

Show in the manual (page 22)
After long periods of use
Service by authorized center

After a longer period of operation, hand the machine in at an authorized MAFELL customer service shop for inspection.

Show in the manual (page 26)
Long term storage
Clean and protect metal parts

If the machine is not used for a long time, clean it carefully and spray bright metal parts with a rust inhibitor.

Show in the manual (page 26)
M: QW-35-FL

Ask a Question

0/1000

Do you recommend KSS60cc?

Yes No

Frequently Asked Questions

A

It is designed for solid wood, including softwood and hardwood, as well as panel materials like MDF, chipboard, and coated boards. It can also cut plastics such as PVC and Plexiglas.

Is this answer helpful?

A

The speed can be adjusted between 2700 and 4700 rpm. Lower speeds prevent burning soft materials, while higher speeds ensure clean cuts in dense hardwoods or plastics.

Is this answer helpful?

A

Yes, the KSS60cc is excellent for plunge cuts. It features a dedicated lever to lower the blade vertically into the material safely and precisely.

Is this answer helpful?

A

It includes an upper fixed guard, a lower retractable guard, a riving knife to prevent kickback, and an automatic brake that stops the blade in 1-2 seconds.

Is this answer helpful?

A

Absolutely. The saw unit can be tilted to any angle between 0 and 45 degrees, allowing for precise bevel cuts for framing and joinery.

Is this answer helpful?

A

Yes, the KSS60cc model typically includes a sturdy transport case to protect the saw and its accessories during storage and transport.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Variable speed control from 2700 to 4700 rpm for optimal cut quality on various materials
  • Advanced safety features including automatic brake and retractable lower guard
  • Capable of precise plunge cuts, bevel cuts up to 45 degrees, and mitre cuts
  • Low vibration levels below 2.5 m/s2 for reduced operator fatigue
  • Includes a durable transport case and essential accessories like parallel stop
VS

Disadvantages

  • Higher price point compared to standard consumer-grade circular saws
  • Requires specific compatible saw blades for optimal performance with the riving knife
  • Heavier weight at 6.1 kg may cause fatigue during extended overhead use
  • Dust extraction requires a dedicated external vacuum with sufficient airflow
  • Complex adjustment mechanisms may require time to master for beginners
M: QW-35-FL

Product Specification

Type

Circular saw

Power

1800W

No-load speed

2700-4700 rpm

Blade diameter

7.28 inches

Cutting capacity

2.64 inches (cutting depth at 0 degrees), 2.09 inches (cutting depth at 45 degrees inclination)

Bevel angle

60 degrees/60 degrees left/right

Tool holder

Bore 0.79 inches

Features

Speed control, rip fence, dust extraction, bevel function

Weight

13.01 lbs

Package contents

Case

M: QW-35-FL

Product Description

Mastering Precision with the Mafell KSS60cc Electric Hand Circular Saw

The Mafell KSS60cc Electric Hand Circular Saw stands as a pinnacle of engineering for woodworkers who demand absolute precision and safety. This robust cross-cutting system is designed specifically for longitudinal and cross-cutting solid wood, as well as processed panel materials like MDF and chipboard. Whether you are a professional carpenter or a serious DIY enthusiast, this tool offers the versatility needed for complex joinery and fine furniture making.

At the heart of the KSS60cc lies a powerful universal motor capable of handling various voltages, ensuring consistent performance across different regions. The electronic speed regulation allows users to adjust the saw blade speed between 2700 and 4700 revolutions per minute. This feature is crucial when working with diverse materials ranging from soft fibers to hard hardwoods or even plastics like PVC. The ability to fine-tune the RPM ensures clean cuts without burning the material, preserving the integrity of your project.

Safety is paramount in the design of this machine. It features an upper fixed guard and a lower retractable guard that automatically covers the blade when not in use. The integrated brake brings the saw blade to a complete stop within one to two seconds after releasing the trigger, significantly reducing the risk of injury. Furthermore, the riving knife prevents kickback by keeping the kerf open during ripping operations, a critical safety mechanism often overlooked in lesser tools.

Versatility is another hallmark of the KSS60cc. The saw unit can be tilted up to 45 degrees for precise bevel cuts, while the mitre guide facilitates accurate angled cross-cuts. For plunge cutting, the unique lever system allows the blade to descend vertically into the workpiece, opening doors for intricate inlays and internal cuts. The included parallel stop and roller edge guide ensure straight, repeatable cuts along existing edges, enhancing workflow efficiency.

The package includes a high-quality carbide-tipped circular saw blade with 32 teeth, ideal for general-purpose cross-cutting. A transport case keeps all components organized and protected, making it easy to move between job sites. With its low vibration levels and effective dust extraction port, the KSS60cc provides a comfortable and cleaner working environment. This saw is more than just a tool; it is a comprehensive solution for high-end woodworking tasks.

Key Notes

  • Always wear hearing protection and a dust mask when operating.
  • Ensure the workpiece is securely clamped before cutting.
  • Use only original MAFELL spare parts to maintain warranty and safety standards.
M: claude-opus-5-5

© Copyright 2026 Manual.ly