Manual.ly Logo

Mafell KSS60cc Manual

0.0 · 0 Ratings

PDF manual · 114 Pages

English

M: claude-opus-5-5
page

/ 114

Loading...
57abd10387217cc4c890ee93b8115e625c53 page 16
-22-
- When restarting a saw in the workpiece, centre
the saw blade in the kerf so that the saw teeth
are not engaged into the material. If a saw blade
binds, it may walk up or kickback from the
workpiece as the saw is restarted.
- Support large panels to minimise the risk of
blade pinching and kickback. Large panels tend
to sag under their own weight. Supports must be
placed under the panel on both sides, near the line
of cut and near the edge of the panel.
- Do not use dull or damaged blades.
Unsharpened or improperly set blades produce
narrow kerf causing excessive friction, blade
binding and kickback.
- Blade depth and bevel adjusting locking levers
must be tight and secure before making the
cut. If blade adjustment shifts while cutting, it may
cause binding and kickback..
- Use extra caution when sawing into existing
walls or other blind areas. The protruding blade
may cut objects that can cause kickback.
Lower guard function
- Check the lower guard for proper closing
before each use. Do not operate the saw if the
lower guard does not move freely and close
instantly. Never clamp or tie the lower guard
into the open position. If the saw is accidentally
dropped, the lower guard may be bent. Raise the
lower guard with the retracting handle and make
sure it moves freely and does not touch the blade
or any other part, in all angles and depths of cut.
- Check the operation of the lower guard spring.
If the guard and the spring are not operating
properly, they must be serviced before use.
Lower guard may operate sluggishly due to
damaged parts, gummy deposits, or a build-up of
debris.
- The lower guard may be retracted manually
only for special cuts such as "plunge cuts" and
"compound cuts". Raise the lower guard by the
retracting handle and as soon as the blade
enters the material, the lower guard must be
released. For all other sawing, the lower guard
should operate automatically.
- Always observe that the lower guard is
covering the blade before placing the saw
down on bench or floor. An unprotected,
coasting blade will cause the saw to walk
backwards, cutting whatever is in its path. Be
aware of the time it takes for the blade to stop after
switch is released.
Riving knife function
- Use the appropriate saw blade for the riving
knife. For the riving knife to function, the body of
the blade must be thinner than the riving knife and
the cutting width of the blade must be wider than
the thickness of the riving knife.
- Adjust the riving knife as described in this
instruction manual. Incorrect spacing, positioning
and alignment can make the riving knife ineffective
in preventing kickback.
- Always use the riving knife except when
plunge cutting. The riving knife must be replaced
after plunge cutting. The riving knife causes
interference during plunge cutting and can create
kickback.
- For the riving knife to work, it must be engaged
in the workpiece. The riving knife is ineffective in
preventing kickback during short cuts.
- Do not operate the saw if the riving knife is
bent Even a light interference can slow the closing
rate of a guard.
Instructions on service and maintenance:
- Regularly cleaning the machine, especially the
adjusting devices and guides, constitutes an
important safety factor.
- Only original MAFELL spare parts and accessories
may be used. Otherwise the manufacturer will not
accept any warranty claims and cannot be held
liable.
4 Setting / Adjustment
4.1 Mains connection
Prior to commissioning make sure that the mains
voltage complies with the operating voltage stated on
the machine's rating plate.

Chat with your Mafell KSS60cc manual using AI

Get instant AI answers from your Mafell KSS60cc manual

Ask anything about the Mafell KSS60cc. Answers come from this manual, with the pages they are based on.

KSS60cc Maintenance Schedule

Before each use
Check lower guard operation

Verify the lower guard closes properly and moves freely before every use. Do not operate if it sticks or fails to close instantly.

Show in the manual (page 22)
Regularly
Clean adjusting devices and guides

Regularly clean the machine, especially the adjusting devices and guides, as this is an important safety factor.

Show in the manual (page 22)
After long periods of use
Service by authorized center

After a longer period of operation, hand the machine in at an authorized MAFELL customer service shop for inspection.

Show in the manual (page 26)
Long term storage
Clean and protect metal parts

If the machine is not used for a long time, clean it carefully and spray bright metal parts with a rust inhibitor.

Show in the manual (page 26)
M: QW-35-FL

Ask a Question

0/1000

Do you recommend KSS60cc?

Yes No

Frequently Asked Questions

A

It is designed for solid wood, including softwood and hardwood, as well as panel materials like MDF, chipboard, and coated boards. It can also cut plastics such as PVC and Plexiglas.

Is this answer helpful?

A

The speed can be adjusted between 2700 and 4700 rpm. Lower speeds prevent burning soft materials, while higher speeds ensure clean cuts in dense hardwoods or plastics.

Is this answer helpful?

A

Yes, the KSS60cc is excellent for plunge cuts. It features a dedicated lever to lower the blade vertically into the material safely and precisely.

Is this answer helpful?

A

It includes an upper fixed guard, a lower retractable guard, a riving knife to prevent kickback, and an automatic brake that stops the blade in 1-2 seconds.

Is this answer helpful?

A

Absolutely. The saw unit can be tilted to any angle between 0 and 45 degrees, allowing for precise bevel cuts for framing and joinery.

Is this answer helpful?

A

Yes, the KSS60cc model typically includes a sturdy transport case to protect the saw and its accessories during storage and transport.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Variable speed control from 2700 to 4700 rpm for optimal cut quality on various materials
  • Advanced safety features including automatic brake and retractable lower guard
  • Capable of precise plunge cuts, bevel cuts up to 45 degrees, and mitre cuts
  • Low vibration levels below 2.5 m/s2 for reduced operator fatigue
  • Includes a durable transport case and essential accessories like parallel stop
VS

Disadvantages

  • Higher price point compared to standard consumer-grade circular saws
  • Requires specific compatible saw blades for optimal performance with the riving knife
  • Heavier weight at 6.1 kg may cause fatigue during extended overhead use
  • Dust extraction requires a dedicated external vacuum with sufficient airflow
  • Complex adjustment mechanisms may require time to master for beginners
M: QW-35-FL

Product Specification

Type

Circular saw

Power

1800W

No-load speed

2700-4700 rpm

Blade diameter

7.28 inches

Cutting capacity

2.64 inches (cutting depth at 0 degrees), 2.09 inches (cutting depth at 45 degrees inclination)

Bevel angle

60 degrees/60 degrees left/right

Tool holder

Bore 0.79 inches

Features

Speed control, rip fence, dust extraction, bevel function

Weight

13.01 lbs

Package contents

Case

M: QW-35-FL

Product Description

Mastering Precision with the Mafell KSS60cc Electric Hand Circular Saw

The Mafell KSS60cc Electric Hand Circular Saw stands as a pinnacle of engineering for woodworkers who demand absolute precision and safety. This robust cross-cutting system is designed specifically for longitudinal and cross-cutting solid wood, as well as processed panel materials like MDF and chipboard. Whether you are a professional carpenter or a serious DIY enthusiast, this tool offers the versatility needed for complex joinery and fine furniture making.

At the heart of the KSS60cc lies a powerful universal motor capable of handling various voltages, ensuring consistent performance across different regions. The electronic speed regulation allows users to adjust the saw blade speed between 2700 and 4700 revolutions per minute. This feature is crucial when working with diverse materials ranging from soft fibers to hard hardwoods or even plastics like PVC. The ability to fine-tune the RPM ensures clean cuts without burning the material, preserving the integrity of your project.

Safety is paramount in the design of this machine. It features an upper fixed guard and a lower retractable guard that automatically covers the blade when not in use. The integrated brake brings the saw blade to a complete stop within one to two seconds after releasing the trigger, significantly reducing the risk of injury. Furthermore, the riving knife prevents kickback by keeping the kerf open during ripping operations, a critical safety mechanism often overlooked in lesser tools.

Versatility is another hallmark of the KSS60cc. The saw unit can be tilted up to 45 degrees for precise bevel cuts, while the mitre guide facilitates accurate angled cross-cuts. For plunge cutting, the unique lever system allows the blade to descend vertically into the workpiece, opening doors for intricate inlays and internal cuts. The included parallel stop and roller edge guide ensure straight, repeatable cuts along existing edges, enhancing workflow efficiency.

The package includes a high-quality carbide-tipped circular saw blade with 32 teeth, ideal for general-purpose cross-cutting. A transport case keeps all components organized and protected, making it easy to move between job sites. With its low vibration levels and effective dust extraction port, the KSS60cc provides a comfortable and cleaner working environment. This saw is more than just a tool; it is a comprehensive solution for high-end woodworking tasks.

Key Notes

  • Always wear hearing protection and a dust mask when operating.
  • Ensure the workpiece is securely clamped before cutting.
  • Use only original MAFELL spare parts to maintain warranty and safety standards.
M: claude-opus-5-5

© Copyright 2026 Manual.ly