Manual.ly Logo

Mafell KSS40 18Mbl Manual

0.0 · 0 Ratings

PDF manual · 110 Pages

English

M: claude-opus-5-5
page

/ 110

Loading...
575b20371ef5fc844bc5aace7612e9356326 page 19
-25-
5.8 Sawing shadow gaps
The minimum shadow gap width is:
- if used without parallel stop 13 mm (33/64 in.)
- if used with parallel stop 14 mm (35/64 in.) (at
cutting depth of 0 - 32 mm / 0 – 1 ¼ in.)
- if used with parallel stop 18 mm (45/64 in.) (at
cutting depth of 32 - 42 mm / 1 ¼ - 1 21/32 in.)
Set the required cutting depth.
Retract the retractable saw guard with the lever
2 (Fig. 3) and set the machine onto the first
fitted workpiece.
Switch on the machine and push the machine
evenly in cutting direction, in addition using the
extraction device.
5.9 Sawing with parallel stop
The parallel stop 4 (Fig. 1) serves to cut parallel to an
already existing edge. The limit stop can be attached
to the left or right of the machine. The cutting range
on the right-hand side amounts to approx. 65 mm (2
9/16 in.) and on the left-hand side to approx. 250 mm
(9 27/32 in.).
You can adjust the cutting width after
unfastening the wing screws 9 (Fig. 2) by
moving the limit stop accordingly and afterwards
refastening the wing screws.
In addition, by simply turning it over (guide surface for
the workpiece edge is pointing upwards), the parallel
stop can be used as double support to improve
machine guidance. Now the machine can be guided
along a lath that is fastened on the workpiece.
5.10 Sawing according to tracings with guide rail
When sawing according to tracing, the right edge of
the guide rail serves as tracing indicator. This also
applies to bevel cuts. Please take note of Section 5.4.
For sawing, place the guide rail onto the
workpiece.
Switch on the machine (see Chapter 5.2) and
slide the machine evenly in cutting direction.
When the cut is completed, switch off the saw
by releasing the switch trigger 2 (Fig. 1)
While it is resting on the workpiece, pull the
machine back into home position and in this
position remove it from the workpiece.
Proceeding in this manner ensures that the
retractable saw guard is completely closed.
5.11 Sawing according to tracings without guide
rail
Danger
When sawing without guide rail it is
imperative to install the enclosed
parallel stop. It serves as double
support to improve machine
guidance and is for your safety.
Set the machine's cutting depth to at least 30 mm (1
3/16 in.). Afterwards, you can remove the machine
from the guide rail to the rear by actuating the locking
lever 20 (Fig. 7).
The base plate is equipped with a tracing edge 10
(Fig. 3) both for straight cuts and for bevel cuts. This
tracing edge corresponds to the saw blade's inside.
For bevel cuts, the tracing can be viewed through the
opening on the left-hand side of the upper saw guard.
Hold the machine by its handles and place the
front part of its base plate onto the workpiece.
Switch on the machine and evenly advance the
machine in cutting direction.
When the cut is completed, switch off the saw
by releasing the switch trigger 2 (Fig. 1).
6 Service and maintenance
Danger
Unplug the rechargeable battery for
all service work.
MAFELL machines are designed to be low in
maintenance.
The ball bearings used are greased for life. When the
machine has been in operation for a longer period of
time, we recommend to hand the machine in at an
authorised MAFELL customer service shop for
inspection.
Only use our special grease, order No. 049040 (1 kg
tin) for all greasing points.
6.1 Storage
If the machine is not used for a longer period of time,
it has to be carefully cleaned. Spray bright metal parts
with a rust inhibitor.

Chat with your Mafell KSS40 18Mbl manual using AI

Get instant AI answers from your Mafell KSS40 18Mbl manual

Ask anything about the Mafell KSS40 18Mbl. Answers come from this manual, with the pages they are based on.

KSS40 18Mbl Maintenance Schedule

Remind me when maintenance is due
Yearly (approx)
Professional inspection by authorized service

After longer periods of operation, hand the machine to an authorized MAFELL service shop for inspection.

Show in the manual (page 25)
Before every use
Check lower saw guard function

Verify the lower guard closes properly and moves freely before each operation. Do not use if it is stuck or does not close immediately.

Show in the manual (page 21)
After long storage
Clean machine and protect metal parts

If not used for a long time, clean the machine thoroughly and spray bare metal parts with a rust inhibitor.

Show in the manual (page 25)

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: QW-35-FL

Ask a Question

0/1000

Do you recommend KSS40 18Mbl?

Yes No

Frequently Asked Questions

A

The Mafell KSS40 offers a maximum cutting depth of 42 mm at 0 degrees and 29 mm at a 45-degree angle. This allows for deep cuts in solid wood and various panel materials while maintaining stability.

Is this answer helpful?

A

The standard package includes two 18V 5.2Ah lithium-ion batteries. This dual-battery setup ensures you have a spare ready while one charges, minimizing downtime on the job site.

Is this answer helpful?

A

Yes, the KSS40 is fully capable of plunge cuts. You must open the lower guard manually using the lever, position the machine against a stop, and then press the plunge lever to lower the blade vertically into the material.

Is this answer helpful?

A

The KSS40 is specifically optimized for the Mafell FLEXI rail system. While it can cut freehand or with a parallel stop, using third-party rails may affect the precision and fit of the guide elements.

Is this answer helpful?

A

Key safety features include an upper fixed guard, a lower retractable guard, an electronic brake that stops the blade quickly, a riving knife to prevent kickback, and isolated handles to protect against hidden wiring.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • High torque 18V motor delivers 6700 RPM for fast, clean cuts in solid wood and panels
  • Includes two 5.2Ah batteries and a fast charger for extended continuous work time
  • Advanced safety features include automatic blade brake and retractable lower guard
  • Compatible with FLEXI rail system for ultra-precise long cuts up to 140 cm
  • Lightweight design at 2.8 kg reduces user fatigue during prolonged overhead work
VS

Disadvantages

  • Higher initial investment cost compared to standard corded circular saws
  • Requires specific Mafell accessories and blades for optimal compatibility
  • Battery life can decrease significantly in extremely cold temperatures below 0°C
  • Maximum cutting depth is limited to 42 mm which may be insufficient for thick timber
  • Dust collection efficiency depends heavily on using an external vacuum extractor
M: QW-35-FL

Product Specification

Type

Circular saw

Battery

2x Battery (18V, 5.2Ah, Li-Ion)

No-load speed

6700 rpm

Blade diameter

4.72 inches

Cutting capacity

1.65 inches (cut depth at 0 degrees), 1.06 inches (cut depth at 45 degrees tilt)

Bevel angle

45 degrees/60 degrees

Arbor hole

0.79 inch

Features

Fence, dust extraction, bevel function

Weight

8.05 lbs

Package contents

Case (T-Max), charger, 2x battery, dust bag, guide rail (FX140)

M: QW-35-FL

Product Description

Mafell KSS40 18Mbl Akku-Handkreissäge: Precision Power in Your Hands

The Mafell KSS40 18Mbl is a top-tier cordless cross-cutting system designed for professional carpenters and woodworkers who demand absolute precision. This versatile tool combines the freedom of battery power with the robust performance of a high-end table saw. Equipped with two 5.2Ah batteries, a dedicated charger, and a durable transport case, this kit is ready to tackle any project from fine joinery to heavy-duty framing.

At the heart of the KSS40 lies an 18-volt motor capable of reaching 6700 RPM at no load. It features a cutting depth of up to 42 mm at 0 degrees and 29 mm at 45 degrees, allowing for deep bevel cuts in solid wood and panel materials alike. The machine includes essential accessories like a carbide-tipped circular saw blade with 24 teeth, a riving knife to prevent kickback, and a parallel stop for consistent rip cuts. For even greater accuracy, the system supports the FLEXI rail FX 140, enabling perfectly straight cuts up to 140 cm without the need for a separate guide rail setup.

Safety is paramount in the design of the KSS40. It comes equipped with both upper fixed and lower retractable saw guards that automatically cover the blade when not in use. The electronic brake ensures the blade stops almost instantly after releasing the trigger. The handle is ergonomically designed with isolated surfaces to protect against hidden electrical cables, and the machine weighs only 2.8 kg without the parallel stop, making it easy to maneuver on-site.

Whether you are creating shadow gaps, performing plunge cuts into existing walls, or executing precise mitre joints, the KSS40 adapts to your needs. The included chip extraction port allows for connection to dust extractors, keeping your workspace clean and reducing health risks associated with wood dust. With its comprehensive set of safety instructions and low vibration levels below 2.5 m/s², this saw ensures a comfortable and secure working experience.

M: claude-opus-5-5

© Copyright 2026 Manual.ly