Manual.ly Logo

Mafell KSS 80 Ec 370 Manual

0.0 · 0 Ratings

PDF manual · 114 Pages

English

M: OA-GPT-5-NAN
page

/ 114

Loading...
be2c959cc8ef5dc27456ded27bfc0686d481 page 10
-16-
Sie können die Schnittbreite nach dem Lösen
der Flügelschrauben 9 (Abb. 2) verstellen, in
dem Sie den Anschlag entsprechend
verschieben, und anschließend die
Flügelschrauben wieder festziehen.
Zusätzlich kann der Parallelanschlag durch einfaches
Umdrehen (Führungsfläche für die Werkstückkante
zeigt nach oben) auch als Doppelauflage zur
besseren Führung der Handkreissäge verwendet
werden. Nun kann die Maschine an einer auf dem
Werkstück befestigten Latte entlanggeführt werden.
5.8 Arbeiten mit dem Untergreifanschlag
Der Untergreifanschlag dient zum Arbeiten parallel zu
einer schon vorhandenen Kante. Dabei kann der
Anschlag sowohl rechts als auch links an der
Maschine angebracht werden. Dabei beträgt der
Schnittbereich auf der rechten Seite ca. 12 - 48 mm
und auf der linken Seite ca. 40 – 280 mm.
Sie können die Schnittbreite nach dem Lösen
der Flügelschrauben 9 (Abb. 2) verstellen, in
dem Sie den Anschlag entsprechend
verschieben, und anschließend die
Flügelschrauben wieder festziehen.
6 Wartung und Instandhaltung
Gefahr
Bei allen Wartungsarbeiten den
Netzstecker ziehen.
MAFELL-Maschinen sind wartungsarm konstruiert.
Die eingesetzten Kugellager sind auf Lebenszeit
geschmiert. Nach längerer Betriebszeit empfehlen
wir, die Maschine einer autorisierten MAFELL-
Kundendienstwerkstatt zur Durchsicht zu übergeben.
Für alle Schmierstellen nur unser Spezialfett, Bestell -
Nr. 049040 (1 kg - Dose), verwenden.
6.1 Lagerung
Wird die Maschine längere Zeit nicht verwendet, ist
sie sorgfältig zu reinigen. Blanke Metallteile mit einem
Rostschutzmittel einsprühen.
7 Störungsbeseitigung
Gefahr
Die Ermittlung der Ursachen von vorliegenden Störungen und deren Beseitigung
erfordern stets erhöhte Aufmerksamkeit und Vorsicht. Vorher Netzstecker ziehen!
Im Folgenden sind einige der häufigsten Störungen und ihre Ursachen aufgeführt. Bei weiteren Störungen
wenden Sie sich bitte an Ihren Händler oder direkt an den MAFELL-Kundendienst.
Störung
Ursache
Beseitigung
Maschine lässt sich nicht
einschalten
Keine Netzspannung
vorhanden
Spannungsversorgung kontrollieren
Netzsicherung defekt
Sicherung ersetzen
Kohlebürsten abgenützt
Maschine in die MAFELL-
Kundendienstwerkstatt bringen
Maschine bleibt während des
Schneidens stehen
Netzausfall
Netzseitige Vorsicherungen
kontrollieren
Überlastung der Maschine
Vorschubgeschwindigkeit verringern
Sägeblatt klemmt beim
Vorschieben der Maschine
Zu großer Vorschub
Vorschubgeschwindigkeit verringern
Stumpfes Sägeblatt
Sofort Schalter loslassen. Maschine
aus dem Werkstück entfernen und
Sägeblatt austauschen
Spannungen im Werkstück
Schlechte Maschinenführung
Parallelanschlag einsetzen
Unebene Werkstückoberfläche
Fläche ausrichten

Chat with your Mafell KSS 80 Ec 370 manual using AI

Get instant AI answers from your Mafell KSS 80 Ec 370 manual

Ask anything about the Mafell KSS 80 Ec 370. Answers come from this manual, with the pages they are based on.

KSS 80 Ec 370 Maintenance Schedule

After long period of use
Professional inspection by authorized service

Hand the machine in to an authorized MAFELL customer service shop for inspection after a longer period of operation.

Show in the manual (page 16)
Before each use
Check lower guard function

Ensure the lower guard closes properly and moves freely; do not operate if it sticks or is damaged.

Show in the manual (page 24)
Regularly
Clean adjusting devices and guides

Regular cleaning of the machine, especially the adjusting devices and guides, is an important safety factor.

Show in the manual (page 13)
M: QW-35-FL

Ask a Question

0/1000

Do you recommend KSS 80 Ec 370?

Yes No

Frequently Asked Questions

A

The saw uses 237 mm diameter carbide-tipped blades with a 30 mm bore. Recommended tooth counts: 12T for rip, 24T for general rip/cross cuts, and 56T for fine cross cuts. Use only blades rated for the saw’s idle speed and EN 847-1 compliant.

Is this answer helpful?

A

Cutting depth is continuously adjustable up to 88 mm (varies with tilt). The saw unit tilts from 0° to 60° for bevel cuts. For the KSS80Ec 370 in cross-cut configuration, effective cutting depths are slightly reduced (e.g., 82/69/55/38 mm at 0°/30°/45°/60°).

Is this answer helpful?

A

Yes: harmful dusts must be extracted with an M-class extractor for prolonged work. The saw’s extraction port diameter is 35 mm and requires an external extractor capable of at least 20 m/s air velocity for effective removal.

Is this answer helpful?

A

The saw includes a riving knife/splitter, upper fixed and lower retractable guards, a large base plate, handles for two-handed control, electronic motor management with overload protection, and an automatic brake. Proper blade choice, secure work support and using the riving knife (except for plunge cuts) also reduce kickback risk.

Is this answer helpful?

A

The KSS80Ec 370 uses a 2300 W universal motor (available for other voltages in some regions). Built-in electronics ensure smooth acceleration, regulate speed under load, and reduce motor output on overload; an automatic brake limits blade coast time to about five seconds.

Is this answer helpful?

A

Yes. The saw handles panel materials like chipboard and MDF when using appropriate blades. Mafell offers guide rails (F80–F310) and accessories to enable accurate guided and long cuts; specialized guide and rail kits increase precision and convenience.

Is this answer helpful?

A

Keep adjustment mechanisms and guides clean of debris, inspect the lower guard and spring, replace worn blades and brushes as needed, and use Mafell-specified grease for lubrication points. For long-term service, have the machine inspected at an authorized Mafell service workshop.

Is this answer helpful?

M: OA-GPT-5-NAN

Advantages and Disadvantages

Advantages

  • High power 2300 W motor with stepless speed control (2250–4400 rpm) for versatile cutting.
  • Comprehensive safety set: upper/lower guards, riving knife, brake and robust base plate.
  • Precise plunge and bevel capability (0°–60°) with adjustable cutting depth up to 88 mm.
  • Compatible with Mafell guide rails and accessories for long, accurate guided cuts.
  • Solid build and low-maintenance design with lifetime-lubricated bearings.
VS

Disadvantages

  • High noise emission (LPA 91 dB(A), LWA 102 dB(A)) requires hearing protection.
  • Weight increases significantly with guiding device (up to ~8.3 kg), affecting portability.
  • Requires correct blade selection and maintenance; improper blades risk kickback or damage.
  • Dust extraction mandatory for health; needs M-class extractor for heavy dust loads.
  • Replacement parts and specialized grease recommended from manufacturer to retain warranty.
M: OA-GPT-5-NAN

Product Specification

Type

Circular Saw

Power

2,300W

No-load speed

2,250-4,400/min

Saw blade diameter

9.33in

Cutting capacity

3.23in (cutting depth at 0 degrees), 2.19in (cutting depth at 45 degrees inclination)

Blade tilt

0-60 degrees

Tool holder

Bore 1.18in

Special features

Speed control, Parallel guide, Dust extraction, Overload protection, Tilt function

Weight

18.30lb

M: OA-GPT-54-NAN

Product Description

Mafell KSS80Ec 370 Electric Hand Circular Saw — Powerful Precision for Professionals

The Mafell KSS80Ec 370 Electric Hand Circular Saw is a robust, professional-grade portable circular saw and cross-cutting system engineered for demanding woodworking tasks. With a 2,300 W universal motor and stepless speed control from 2,250 to 4,400 rpm, it delivers consistent cutting performance across hardwood, softwood and engineered panels. The KSS80Ec 370 variant adds a guiding assembly to expand cutting length (370 mm at 80 mm workpiece thickness) and enhance accuracy for rip and cross cuts.

Designed for tradespeople and serious hobbyists, the saw emphasizes safety and usability. It includes upper and retractable lower guards, a riving knife/splitter, a built-in brake, and a large base plate for stability. The electronic motor management ensures smooth acceleration and overload protection; an automatic brake reduces blade coast time to about five seconds. The machine accepts 237 mm carbide-tipped blades (30 mm bore) and ships with a 12-tooth blade, riving knife, parallel guide and service tool depending on model configuration.

Versatility is a core strength: plunge cuts, bevel cuts from 0°–60°, and adjustable cutting depths up to 88 mm (varying with tilt) are supported. The saw’s bevel and depth scales, plunge-latch mechanism and adjustable riving knife make repetitive and precise operations straightforward. Dust management is addressed with a 35 mm extraction port; users are advised to connect an M-class extractor for health protection during heavy dust generation.

Technical highlights include clear specifications for cutting depths and blade sizes, robust safety devices, and optional guide rails (F80–F310) and accessories to expand capability. The manual provides step-by-step procedures for blade changes, setting the riving knife, using the parallel or roller edge guides, and troubleshooting common faults. Emission data (LPA 91 dB(A), LWA 102 dB(A)) and vibration (<2.5 m/s2) are stated, so users can plan PPE and jobsite measures accordingly.

With careful adherence to safety instructions (use of hearing and dust protection, correct blade selection, secure clamping of workpieces), the KSS80Ec 370 offers controlled, accurate cuts and dependable durability in professional environments.

Notes

  • Use only approved blades (EN 847-1) with correct bore and dimensions; avoid damaged or HSS blades.
  • Always connect adequate dust extraction (air velocity ≥ 20 m/s) for prolonged work.
  • Regularly clean adjustments and guides; use original Mafell spare parts and grease as specified.
M: OA-GPT-5-NAN

© Copyright 2026 Manual.ly