Manual.ly Logo

Mafell KSS 80 Ec 370 Manual

0.0 · 0 Ratings

PDF manual · 114 Pages

English

M: OA-GPT-5-NAN
page

/ 114

Loading...
be2c959cc8ef5dc27456ded27bfc0686d481 page d
-13-
Funktion des Spaltkeils
- Verwenden Sie das für den Spaltkeil passende
Sägeblatt. Damit der Spaltkeil wirkt, muss das
Stammblatt des Sägeblatts dünner als der
Spaltkeil sein und die Zahnbreite mehr als die
Spaltkeildicke betragen.
- Justieren Sie den Spaltkeil wie in dieser
Betriebsanleitung beschrieben. Falsche
Abstände, Position und Ausrichtung können der
Grund dafür sein, dass der Spaltkeil einen
Rückschlag nicht wirksam verhindert.
- Verwenden Sie immer den Spaltkeil, außer bei
„Tauchschnitten“. Montieren Sie den Spaltkeil
nach dem Tauchschnitt wieder. Der Spaltkeil stört
bei Tauchschnitten und kann einen Rückschlag
erzeugen. Dieser Absatz gilt nur für
Handkreissägen ohne MAFELL-Flippkeil.
- Damit der Spaltkeil wirken kann, muss er sich
im Sägespalt befinden. Bei kurzen Schnitten ist
der Spaltkeil unwirksam beim Verhindern eines
Rückschlags.
- Betreiben Sie die Säge nicht mit verbogenem
Spaltkeil. Bereits eine geringe Störung kann das
Schließen der Schutzhaube verlangsamen.
Hinweise zur Wartung und Instandhaltung:
- Die regelmäßige Reinigung der Maschine, vor
allem der Verstelleinrichtungen und der
Führungen, stellt einen wichtigen Sicherheitsfaktor
dar.
- Es dürfen nur original MAFELL-Ersatz- und
Zubehörteile verwendet werden. Es besteht sonst
kein Garantieanspruch und keine Haftung des
Herstellers.
4 Rüsten / Einstellen
4.1 Netzanschluss
Achten Sie vor Inbetriebnahme darauf, dass die
Netzspannung mit der auf dem Leistungsschild der
Maschine angegebenen Betriebsspannung
übereinstimmt.
4.2 Späneabsaugung
Gefahr
Gesundheitsgefährdende Stäube
müssen mit einem M-Sauger
eingesaugt werden.
Bei allen Arbeiten, bei denen eine erhebliche Menge
Staub entsteht, schließen Sie die Maschine an eine
geeignete externe Absaugeinrichtung an. Die
Luftgeschwindigkeit muss mindestens 20 m/s
betragen.
Der Innendurchmesser des Absaugstutzens 3 (Abb.
1) beträgt 35 mm.
4.3 Sägeblattauswahl
Um eine gute Schnittqualität zu erhalten, verwenden
Sie ein scharfes Werkzeug und wählen entsprechend
Material und Anwendung ein Werkzeug aus der
folgenden Liste:
Schneiden von Weich- und Hartholz quer und
längs zur Faserrichtung:
- HM-Kreissägeblatt Ø 237 x 2,5 x 30 mm, 24 Zähne
Schneiden von Weich- und Hartholz speziell längs
zur Faserrichtung:
- HM-Kreissägeblatt Ø 237 x 2,5 x 30 mm, 12 Zähne
Schneiden von Weich- und Hartholz speziell quer
zur Faserrichtung:
- HM-Kreissägeblatt Ø 237 x 2,5 x 30 mm, 56 Zähne
4.4 Sägeblattwechsel
Gefahr
Bei allen Wartungsarbeiten den
Netzstecker ziehen.
Betätigen Sie den Drücker 2 (Abb. 2) und
ziehen den Sperrhebel 19 nach oben. Nun ist
die Sägewelle arretiert und der Schalthebel
verriegelt. Sie können die bewegliche
Schutzhaube mit Hilfe des Voreinzugshebels 1
(Abb. 2) oder von Hand in geöffneter Stellung
arretieren um den Werkzeugwechsel zu
erleichtern.
Mit dem Sechskant-Schraubendreher 5
(Halterung Abb. 2) lösen Sie die Flansch-
Schraube 18 (Abb. 3) entgegen dem

Chat with your Mafell KSS 80 Ec 370 manual using AI

Get instant AI answers from your Mafell KSS 80 Ec 370 manual

Ask anything about the Mafell KSS 80 Ec 370. Answers come from this manual, with the pages they are based on.

KSS 80 Ec 370 Maintenance Schedule

After long period of use
Professional inspection by authorized service

Hand the machine in to an authorized MAFELL customer service shop for inspection after a longer period of operation.

Show in the manual (page 16)
Before each use
Check lower guard function

Ensure the lower guard closes properly and moves freely; do not operate if it sticks or is damaged.

Show in the manual (page 24)
Regularly
Clean adjusting devices and guides

Regular cleaning of the machine, especially the adjusting devices and guides, is an important safety factor.

Show in the manual (page 13)
M: QW-35-FL

Ask a Question

0/1000

Do you recommend KSS 80 Ec 370?

Yes No

Frequently Asked Questions

A

The saw uses 237 mm diameter carbide-tipped blades with a 30 mm bore. Recommended tooth counts: 12T for rip, 24T for general rip/cross cuts, and 56T for fine cross cuts. Use only blades rated for the saw’s idle speed and EN 847-1 compliant.

Is this answer helpful?

A

Cutting depth is continuously adjustable up to 88 mm (varies with tilt). The saw unit tilts from 0° to 60° for bevel cuts. For the KSS80Ec 370 in cross-cut configuration, effective cutting depths are slightly reduced (e.g., 82/69/55/38 mm at 0°/30°/45°/60°).

Is this answer helpful?

A

Yes: harmful dusts must be extracted with an M-class extractor for prolonged work. The saw’s extraction port diameter is 35 mm and requires an external extractor capable of at least 20 m/s air velocity for effective removal.

Is this answer helpful?

A

The saw includes a riving knife/splitter, upper fixed and lower retractable guards, a large base plate, handles for two-handed control, electronic motor management with overload protection, and an automatic brake. Proper blade choice, secure work support and using the riving knife (except for plunge cuts) also reduce kickback risk.

Is this answer helpful?

A

The KSS80Ec 370 uses a 2300 W universal motor (available for other voltages in some regions). Built-in electronics ensure smooth acceleration, regulate speed under load, and reduce motor output on overload; an automatic brake limits blade coast time to about five seconds.

Is this answer helpful?

A

Yes. The saw handles panel materials like chipboard and MDF when using appropriate blades. Mafell offers guide rails (F80–F310) and accessories to enable accurate guided and long cuts; specialized guide and rail kits increase precision and convenience.

Is this answer helpful?

A

Keep adjustment mechanisms and guides clean of debris, inspect the lower guard and spring, replace worn blades and brushes as needed, and use Mafell-specified grease for lubrication points. For long-term service, have the machine inspected at an authorized Mafell service workshop.

Is this answer helpful?

M: OA-GPT-5-NAN

Advantages and Disadvantages

Advantages

  • High power 2300 W motor with stepless speed control (2250–4400 rpm) for versatile cutting.
  • Comprehensive safety set: upper/lower guards, riving knife, brake and robust base plate.
  • Precise plunge and bevel capability (0°–60°) with adjustable cutting depth up to 88 mm.
  • Compatible with Mafell guide rails and accessories for long, accurate guided cuts.
  • Solid build and low-maintenance design with lifetime-lubricated bearings.
VS

Disadvantages

  • High noise emission (LPA 91 dB(A), LWA 102 dB(A)) requires hearing protection.
  • Weight increases significantly with guiding device (up to ~8.3 kg), affecting portability.
  • Requires correct blade selection and maintenance; improper blades risk kickback or damage.
  • Dust extraction mandatory for health; needs M-class extractor for heavy dust loads.
  • Replacement parts and specialized grease recommended from manufacturer to retain warranty.
M: OA-GPT-5-NAN

Product Specification

Type

Circular Saw

Power

2,300W

No-load speed

2,250-4,400/min

Saw blade diameter

9.33in

Cutting capacity

3.23in (cutting depth at 0 degrees), 2.19in (cutting depth at 45 degrees inclination)

Blade tilt

0-60 degrees

Tool holder

Bore 1.18in

Special features

Speed control, Parallel guide, Dust extraction, Overload protection, Tilt function

Weight

18.30lb

M: OA-GPT-54-NAN

Product Description

Mafell KSS80Ec 370 Electric Hand Circular Saw — Powerful Precision for Professionals

The Mafell KSS80Ec 370 Electric Hand Circular Saw is a robust, professional-grade portable circular saw and cross-cutting system engineered for demanding woodworking tasks. With a 2,300 W universal motor and stepless speed control from 2,250 to 4,400 rpm, it delivers consistent cutting performance across hardwood, softwood and engineered panels. The KSS80Ec 370 variant adds a guiding assembly to expand cutting length (370 mm at 80 mm workpiece thickness) and enhance accuracy for rip and cross cuts.

Designed for tradespeople and serious hobbyists, the saw emphasizes safety and usability. It includes upper and retractable lower guards, a riving knife/splitter, a built-in brake, and a large base plate for stability. The electronic motor management ensures smooth acceleration and overload protection; an automatic brake reduces blade coast time to about five seconds. The machine accepts 237 mm carbide-tipped blades (30 mm bore) and ships with a 12-tooth blade, riving knife, parallel guide and service tool depending on model configuration.

Versatility is a core strength: plunge cuts, bevel cuts from 0°–60°, and adjustable cutting depths up to 88 mm (varying with tilt) are supported. The saw’s bevel and depth scales, plunge-latch mechanism and adjustable riving knife make repetitive and precise operations straightforward. Dust management is addressed with a 35 mm extraction port; users are advised to connect an M-class extractor for health protection during heavy dust generation.

Technical highlights include clear specifications for cutting depths and blade sizes, robust safety devices, and optional guide rails (F80–F310) and accessories to expand capability. The manual provides step-by-step procedures for blade changes, setting the riving knife, using the parallel or roller edge guides, and troubleshooting common faults. Emission data (LPA 91 dB(A), LWA 102 dB(A)) and vibration (<2.5 m/s2) are stated, so users can plan PPE and jobsite measures accordingly.

With careful adherence to safety instructions (use of hearing and dust protection, correct blade selection, secure clamping of workpieces), the KSS80Ec 370 offers controlled, accurate cuts and dependable durability in professional environments.

Notes

  • Use only approved blades (EN 847-1) with correct bore and dimensions; avoid damaged or HSS blades.
  • Always connect adequate dust extraction (air velocity ≥ 20 m/s) for prolonged work.
  • Regularly clean adjustments and guides; use original Mafell spare parts and grease as specified.
M: OA-GPT-5-NAN

© Copyright 2026 Manual.ly