Lupine SL Nano Manual
PDF manual · 11 Pages
English

Quick check
Incorrect answer, please try again.
Chat with your Lupine SL Nano manual using AI
Get instant AI answers from your Lupine SL Nano manual
Ask anything about the Lupine SL Nano. Answers come from this manual, with the pages they are based on.
SL Nano Maintenance Schedule
Do not use a strong water jet or heavy detergent to clean the lamp.
If the LED light source is defective, replace the entire headlight; repairs are only possible at Lupine.
Ask a Question
Do you recommend SL Nano?
Yes NoFrequently Asked Questions
The SL Nano offers DRL (~2 W), low beam (factory 5–8 W depending on mode), and high beam (factory 8–14 W). Maximum stated output is up to 900 lumens. ECO factory settings are High 14 W, Low 8 W, DRL 2 W.
Is this answer helpful?
All components are waterproof and the housing meets IP68, but the lamp is not suitable for underwater use. It is designed for severe weather conditions but should not be used as a diving light.
Is this answer helpful?
Position the clamp halves around the left side of the stem, insert the M4 bolt with O-ring(s) in order, and tighten the clamp to the lamphead with the supplied keys (3 mm at 2 Nm, final 2.5 mm at max 1 Nm). Keep the mount close to the stem and ensure notches interlock.
Is this answer helpful?
Check that the light cable is connected, the light input is activated in the bike’s software, and the drive unit voltage is sufficient (switch to 12 V if needed). Also verify compatibility at lupine.de and try resetting to factory settings.
Is this answer helpful?
No. If an LED or the light source fails the entire headlight must be replaced or serviced by Lupine. Replacement or repair is handled only by Lupine to maintain safety and performance.
Is this answer helpful?
Yes. When DRL is active the built-in ambient sensor measures light every ~5 seconds and will automatically switch to low beam when it becomes sufficiently dark. It does not automatically revert from low beam to DRL.
Is this answer helpful?
Compatibility depends on the e-bike drive system. The bike must provide stable power and light input activation; some systems require dealer activation. The headlight can be used if the drive prevents deep battery discharge and/or supplies sufficient light power.
Is this answer helpful?
Advantages and Disadvantages
Advantages
- Compact CNC aluminum body (30x41x41 mm) with IP68 waterproofing.
- Up to 900 lumens with selectable DRL, low and high beam modes.
- Built-in ambient light sensor for automatic DRL-to-low-beam switching.
- Simple clamp mount and optional stem kit for centered installation.
- Robust thermal design allows stationary operation without damage.
Disadvantages
- Not suitable for underwater use despite IP68 rating.
- If an LED fails, entire lamp must be replaced—no user repair.
- Requires compatible bike drive and light input activation on some e-bikes.
- Small size limits heat dissipation at very high continuous output.
- Wired remote required for mode indication and switching; adds cabling.
Product Specification
Type
Front light
Colors
black, grey
Max. light output
900lm
Light source
2x LED
Light mode
Continuous light
Power supply
36V (E-Bike)
Mounting
Bracket
Dimensions
1.18x1.61x1.61in
Weight
0.11 lb
Special features
waterproof, dustproof, exclusively for e-bikes, StVZO compliant
Product Description
Lupine SL Nano Front Light Manual — Compact Power for Every Ride
The Lupine SL Nano Front Light is a compact, high-performance bicycle headlight designed for reliable daytime visibility and powerful low- and high-beam illumination. Engineered from CNC-machined 6061-T6 aluminum and sealed to IP68 standards, the SL Nano packs two Osram automotive LEDs behind a biconical TIR lens into a tiny 30 x 41 x 41 mm housing. It delivers up to 900 lumens (max), with configurable outputs for daytime running light (DRL), low beam and high beam, and offers robust thermal design so it can safely operate while stationary or in motion.
Practical installation and durability are central to the SL Nano. The mount uses a simple clamp system with M4 hardware and O-rings to secure the lamp near the stem; recommended mount heights are 400–1,200 mm with the light cone’s half-height positioned at 5 m. An optional stem kit enables centric mounting on wider stems. The wired remote button mounts beside the grip and indicates active modes with colored LEDs: green for low beam, blue for high beam, and off or no light for DRL or standby.
User controls and electronics offer flexible programming. Out of the box the lamp defaults to ECO settings (factory low/high/DRL wattages), but users can customize output levels and toggle modes via the wired remote and the bike’s display. A built-in ambient light sensor (measuring every ~5 seconds) automatically switches DRL to low beam when darkness is detected. The lamp operates from 6–12 V systems; compatibility with the bike’s drive unit and activation of the light input in the drive software may be required.
Safety and maintenance are emphasized: never look directly into the beam or use strongly focusing optics; keep the housing away from flammable materials because it can heat in use; and carry a spare light since LED or light-source failures require replacement of the entire lamp—repairs and replacements are handled by Lupine. While the unit is fully waterproof and rated IP68, it is not intended for underwater use. Clean with gentle methods only.
With straightforward mounting, clear troubleshooting steps (check cable, activation, voltage, or return to factory settings), and robust materials and sealing, the SL Nano suits commuters and e-bike riders who need a compact, dependable headlight that balances daytime visibility and night-time illumination.
Notes
- Factory ECO mode: High beam 14 W, Low beam 8 W, DRL 2 W. Custom lower-power presets available.
- If one LED fails, headlight functions may be disabled; replacement required via Lupine.
- Compatible with e-bike systems only if the drive provides stable light power and proper cut-off/charging safeguards.
Search for 67,706 Manuals online
Type-in Brand or Model