Manual.ly Logo

Kranzle X Series Manual

0.0 · 0 Ratings

PDF manual · 19 Pages

English

M: gpt-5.6-terra
page

/ 19

Loading...
d00417c7bd8618aed74f9e6ac64fea4e4b4f page 9
16 17
Motor protection switch
Motor is protected against overload by means of a motor protection switch.
In case of motor overload or blocking, the motor of the high pressure cleaner
switches off automatically. If motor tends to switch off repeatedly, make sure
to detect appears. Make sure to detect and remedy the cause of the failure.
Replacements and inspection work should only be performed by
qualified persons when the high pressure cleaner is disconnected from
the power supply, i.e. with plug pulled out from the electrical socket.
Totalstop system
The X-series features a totalstop system. If the main switch is switched on, the
motor is started via a pressure switch when opening the safety trigger gun. When
closing the safety trigger gun the motor is switched off immediately.
High pressure hose and spray device
The high pressure hose and spray device which are part of the X-series
equipment, are made of high quality material and engineered to conform with
the operating conditions of the high pressure cleaner and are duly labeled.
If replacement parts are required, only such parts that are authorized
by the manufacturer may be used. The warranty is automatically void if
spare parts of third-party providers are used! The high pressure hose and
spray device must be connected in a pressure-tight manner
(without leakage).
The high pressure hose may not be driven over, pulled excessively, or
twisted. The high pressure hose may under no circumstances be pulled
over sharp edges. Defective high pressure hoses must not be repaired
(acc. to DIN 20022) but have to be replaced by new hoses approved by
the manufacturer.
Prior to putting the high pressure cleaner into operation make sure
that all safety instructions be observed.
Water and cleaning system
Water must be supplied to the high pressure pump under pressure or
(only for high-
pressure cleaner X A15 TST)
directly sucked
in out of a pressureless container. The
water is then forced under pressure by the high pressure pump to the lance. The
high pressure jet is formed by the nozzle at the end of the lance.
Environmental, refuse disposal and water protection regulations
must be observed!
Safety jet pipe with safety trigger gun
The high-pressure cleaner can only be operated when the trigger of the safety
deactivation trigger gun's trigger is actuated. When the trigger is pulled, the sa-
fety deactivation trigger gun opens. The liquid is then transported to the nozzle.
The spray pressure increases and quickly reaches the operating pressure. When
the trigger is released, the safety deactivation trigger gun closes and any further
spraying of liquid from the safety jet pipe is prevented. The pressure gauge must
show "0" bar. The increase in pressure when the safety deactivation trigger gun
is closed causes the pressure control valve-safety valve to open. The motor is
switched off by the pressure switch. When the trigger gun with safety catch is
opened, the pressure control valve - safety valve closes, the motor is started and
the high-pressure pump resumes pressure spraying from the safety jet pipe with
the selected operating pressure.
The safety trigger gun is a safety device. Repairs should only be
performed by qualified persons. Should replacement parts be required,
use only components authorized by the manufacturer.
Pressure control valve/safety valve
The pressure control valve/safety valve protects the high pressure cleaner from
a build up of excess pressure, and is designed not to permit an excess pressure
to be selected for operation. The limit nut on the handle is sealed with a spray
coating. The operating pressure and spray rate can be steplessly adjusted by
turning the handle.
Replacements, repairs, new adjustments and sealing should only be
performed by qualified persons.
Functional details Functional details

Chat with your Kranzle X Series manual using AI

Get instant AI answers from your Kranzle X Series manual

Ask anything about the Kranzle X Series. Answers come from this manual, with the pages they are based on.

X Series Maintenance Schedule

Remind me when maintenance is due
Yearly or every 250 operating hours
Change the gearbox oil

Change oil annually or after 250 operating hours. The first oil change is due after about 50 operating hours; change immediately if oil is gray or white.

Show in the manual (page 12)
Yearly
Have the pressure washer safety-inspected

Have a qualified person inspect safe operation as needed, but at least every 12 months. Record the inspection results in writing.

Show in the manual (page 12)
Before each use
Inspect hoses, power cable, and shut-off gun

Check the high-pressure hose, mains cable, and safety shut-off gun for damage. Replace defective or damaged components immediately.

Before each use
Clean and inspect the water inlet filter

Check the water inlet screen for cleanliness and damage. Rinse it thoroughly with clean water; do not operate without it or with a damaged filter.

Before each use
Check the oil level

Check the oil level using the dipstick. It must reach the upper edge of the OK marking.

Regularly
Lubricate the plug nipple

Apply acid-free grease to the plug nipple regularly.

Show in the manual (page 18)
After each use
Lock the safety shut-off gun

Engage the safety lock on the shut-off gun after every use to prevent unintentional spraying.

After each use
Clean hoses, cable, and water inlet filter

During shutdown, clean and coil the high-pressure hose and mains cable, and clean the water inlet filter.

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: gpt-5.6-terra

Ask a Question

0/1000

Do you recommend X Series?

Yes No

Frequently Asked Questions

A

The range includes the X A15 TST and X A17 TST electric high-pressure washers. Both use a mobile chassis, hose reel, pressure gauge, adjustable output, safety trigger gun, and Total Stop System.

Is this answer helpful?

A

The standard equipment includes a flat-fan nozzle for broader cleaning coverage and a dirt-killer nozzle for concentrated cleaning of stubborn grime. Both connect through the safety trigger gun coupling.

Is this answer helpful?

A

Only the X A15 TST supports direct suction. Use a suitable suction hose with filter, fill the pump and hose with water before first use, and draw only clean, non-chlorinated water without air entering the system.

Is this answer helpful?

A

The washer can be connected to cold water or water up to 60 C. Hot inlet water raises the temperature of metal components, so protective gloves are recommended when handling the unit.

Is this answer helpful?

A

When the main switch is on, pulling the trigger starts the motor through a pressure switch. Releasing the trigger stops water flow and shuts off the motor. This provides convenient, controlled operation.

Is this answer helpful?

A

Turn it off, stop the water supply, release pressure, lock the trigger gun, drain the pump, unplug it, clean and coil the hose and cable, clean the inlet filter, and store the unit in a frost-free place.

Is this answer helpful?

M: gpt-5.6-terra

Advantages and Disadvantages

Advantages

  • Compact, wheeled design with a chassis suited to uneven ground and stairs.
  • Brass pump head, steel-braided 12 m hose, and organized onboard storage support durable daily use.
  • Total Stop System stops the motor when the trigger is released, reducing unnecessary runtime.
  • Adjustable pressure and water volume help match cleaning force to different surfaces.
  • X A15 TST supports direct suction from clean water containers with the correct hose and filter.
VS

Disadvantages

  • Requires careful water-supply checks; insufficient flow can damage the pump through cavitation.
  • The X A15 TST alone supports direct suction, so this feature is not available on every X-Serie model.
  • High-pressure use demands protective equipment and careful distance control on sensitive surfaces.
  • Hose length is limited to 20 m when extending the original hose.
  • Regular oil checks, filter cleaning, frost protection, and periodic servicing are necessary.
M: gpt-5.6-terra

Product Specification

Operating mode

Cold water

Mobility

Trolley

Fuel tank

No

M: gpt-5.6-terra

Product Description

Kraenzle X-Serie Electric High-Pressure Washer

The Kraenzle X-Serie Electric High-Pressure Washer is built for users who expect dependable cleaning power in a compact, mobile format. Designed for demanding home, property, workshop, and light professional tasks, the X A15 TST and X A17 TST combine sturdy construction with practical controls for effective outdoor cleaning. Driveways, vehicles, patios, equipment, walls, and garden furniture can be refreshed with a focused water jet and a choice of spray patterns.

Built for Controlled Cleaning

A special brass pump head supports long-term durability, while the continuously adjustable pressure and water-volume control lets operators match the output to the surface. This is helpful when moving from resilient paving stones to more delicate vehicle panels or painted surfaces. The included flat-fan nozzle provides broad, even coverage, and the dirt-killer nozzle delivers a more concentrated action for stubborn soil.

The electric washer uses a Total Stop System that starts the motor when the trigger gun is opened and stops it when the trigger is released. This feature helps reduce unnecessary motor running and keeps operation straightforward. A pressure gauge gives a clear indication of working conditions, while the safety trigger gun is designed for controlled use.

Mobile Design and Useful Storage

The X-Serie has a robust wheeled chassis made to handle uneven ground and steps. Its ergonomic handle makes positioning easier around a work area. TST versions include a hose reel with a 12 m steel-braided high-pressure hose, helping keep the hose organized before, during, and after use. Integrated holders for the trigger gun, nozzles, cable, and accessories support a tidier setup.

The washer accepts cold water and inlet water up to 60 C, provided the supply meets the required flow and pressure conditions. The X A15 TST can also draw clean water from a separate container or pond when fitted with the appropriate suction hose and filter. This adds flexibility where a pressurized water connection is unavailable.

Safety and Care Matter

Correct setup is essential for reliable performance. Inspect the inlet filter, hose, cable, and connections before use, fully unwind the high-pressure hose, and avoid running the pump dry. Keep the spray away from people, animals, electrical equipment, and fragile surfaces. Protective clothing, eye protection, hearing protection, and stable footing are important during operation.

Regular care includes cleaning the water inlet filter, checking the oil level, draining the unit before freezing conditions, and using approved replacement parts. The first oil change is recommended after about 50 operating hours, followed by annual service or service every 250 hours.

Notes

  • Use a residual-current device rated at 30 mA and a properly protected 16 A electrical supply.
  • Maintain at least 30 cm from sensitive surfaces such as vehicle tires.
  • Commercial units should receive a qualified safety inspection at least every 12 months.
M: gpt-5.6-terra

© Copyright 2026 Manual.ly