Manual.ly Logo

Jung Pumpen Simer 5 Manual

0.0 · 0 Ratings

PDF manual · 48 Pages

English

M: QW-35-FL
page

/ 48

Loading...
636a128d27127f216513b7ef03502cfb17d7 page 9
9 9
ENGLISH
MAINTENANCE
WARNING!
Before carrying out any works: disconnect the
pump and the controls from the mains and take
steps to ensure that no one else can reconnect
them to the power supply.
WARNING!
Check the mains cable for signs of mechanical
and chemical damage. Damaged or kinked ca-
bles must be replaced.
NOTICE! If the water contains high levels of iron
or lime, insucient cleaning can result in irrep-
arable damage to the seal and thus also to the
pump motor in the long term.
Consequently, the pump must be cleaned at
regular intervals according to the hardness of
the water.
Cleaning
The inlet strainer prevents coarse dirt from en-
tering the pump. Cleaning the strainer at regular
intervals ensures the best possible operation
and performance.
Changing the oil
The oil should be changed after every 1000
hours of operation. An oil screw (OIL) on top of
the pump housing is provided for this purpose.
The oil chamber may be lled with no more than
200 ml of oil (ZBR39630). Overlling the cham-
ber will cause permanent damage to the pump.
QUICK TIPS FOR
REMEDYING FAULTS
Pump does not work
Check mains current (do not use a pin gauge)
• Fuse faulty = may be too weak (please refer to
Electrical Connection)
• Mains cable damaged = replace cable
Impeller blocked
• Solids and brous matter have become
lodged in the pump housing = clean
Decrease in pump performance
• Strainer is blocked = clean
• Discharge hose is blocked = clean
• Kinks in discharge hose = lay without kinks
• Impeller is worn = replace pump
Intake suction impaired
• Vent valve is blocked = clean
• Strainer or impeller is blocked = clean

Chat with your Jung Pumpen Simer 5 manual using AI

Get instant AI answers from your Jung Pumpen Simer 5 manual

Ask anything about the Jung Pumpen Simer 5. Answers come from this manual, with the pages they are based on.

Simer 5 Maintenance Schedule

Regularly (based on water hardness)
Clean the pump and inlet strainer

Clean the pump regularly depending on water hardness to prevent seal damage. Clean the inlet strainer to ensure maximum performance.

Every 1000 operating hours
Change the oil

Perform an oil change after every 1000 hours of operation. Fill the oil chamber with a maximum of 200 ml; overfilling damages the pump.

M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend Simer 5?

Yes No

Frequently Asked Questions

A

The pump is effective starting from water levels of 5 mm and can drain surfaces down to a residual level of 2 mm.

Is this answer helpful?

A

No, the Simer pump is not suitable for saline media or water containing fish, as it may cause damage or harm aquatic life.

Is this answer helpful?

A

The oil should be changed after every 1000 hours of operation to ensure the pump continues to function correctly.

Is this answer helpful?

A

You should not run the pump dry for more than 20 minutes. Extended dry running can damage the internal components.

Is this answer helpful?

A

The pump must be connected to a socket protected by at least a 10 A slow-blow fuse and a 30 mA RCD safety switch.

Is this answer helpful?

A

Always lift the pump using the carrying handle. Never lift it by the power cable, and lower it into place using a rope or chain.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Can drain water down to a residual level of just 2 mm
  • Stepped hose connector fits 1/2", 3/4", and 1" hoses easily
  • Built-in thermal protection prevents motor damage from overheating
  • Effective for various applications like draining cellars, pools, and roofs
VS

Disadvantages

  • Not suitable for pumping saline water or water from fish ponds
  • Requires regular oil changes every 1000 operating hours
  • Cannot be permanently connected to building drainage systems
  • Must be kept away from freezing conditions when in use
M: QW-35-FL

Product Specification

Power

190W

Flow rate

1135.8 gpm

Head height

19.69 ft

Pressure connection

1 1/4"

Hose connection

1/2", 3/4", 1"

Features

no tank, IP68, overload protection

Cable length

32.81 ft

Weight

11.02 lbs

M: QW-35-FL

Product Description

Jung Pumpen Simer 5 Electric Submersible Pump 10m - Read, Download & Print Free

The Jung Pumpen Simer 5 Electric Submersible Pump is a versatile and robust solution designed for efficient water management in various environments. Whether you are dealing with flooded basements, draining roof surfaces, or clearing puddles on sports courts, this pump delivers reliable performance. It is engineered to handle water levels as low as 5 mm, ensuring that residual water can be reduced to just 2 mm without the need for additional accessories. This capability makes it an ideal choice for homeowners and professionals alike who require precise drainage control.

Constructed with durability in mind, the Simer 5 features a stepped hose connector compatible with 1/2", 3/4", and 1" hoses, allowing for immediate operation once connected. The automatic vent valve at the base ensures smooth operation by preventing air locks, although users must keep this area clean to maintain optimal function. The pump is equipped with a winding thermostat that automatically shuts off the unit if temperatures become dangerously high due to dry running or overload, protecting the motor from irreversible damage.

Safety is paramount with this device. It should only be connected to properly installed sockets protected by a 10 A fuse and a residual current device (RCD) of 30 mA. Users must never operate the pump while a person is in the water. Additionally, the pump is not suitable for saline media or fish ponds, and the pumped medium temperature must not exceed 60°C. Regular maintenance, including cleaning the inlet strainer and changing the oil every 1000 hours, is essential to prolong the life of the equipment.

Important Notes

  • Always disconnect power before performing any maintenance.
  • Do not run the pump dry for more than 20 minutes.
  • Lift the pump by the handle, never by the cable.
  • Ensure the work area is free of toxic gases before use.
M: QW-35-FL

© Copyright 2026 Manual.ly