Manual.ly Logo

Jung Pumpen Multidrain UV 620-1 Manual

0.0 · 0 Ratings

PDF manual · 48 Pages

English

M: QW-35-FL
page

/ 48

Loading...
c705e44072c112ce647999a64ecbeb2dca33 page 7
ENGLISH
You have purchased a product made by
Pentair Jung Pum-
pen
and with it, therefore, also excellent quality and service.
Secure this service by carrying out the installation works
in accordance with the instructions, so that our product
can perform its task to your complete satisfaction. Please
remember that damage caused by incorrect installation or
handling will adversely affect the guarantee. Therefore ple-
ase adhere to the instructions in this manual!
This appliance can be used by children aged 8 years or over
and by persons with limited physical, sensory or intellectual
capabilities, or with limited experience and knowledge, pro-
vided that they are supervised or have been instructed in
the safe use of the appliance and are aware of the dangers
involved. Children must not be allowed to play with the ap-
pliance. Cleaning and user maintenance must not be carried
out by children unless they are supervised.
If this unit is equipped with a mains connection line wi-
thout a plug or other means of disconnection from the
mains, a complete disconnecting device must be installed
on site in the xed electrical installation in accordance
with the installation regulations. A main switch of overvol-
tage category III can be installed as a complete discon-
necting device. If the mains connection cable of this unit
is damaged, it must be replaced by the manufacturer or its
customer service or a similarly qualied person in order to
avoid hazards.
Damage prevention in case of failure
Like any other electrical device, this product may fail due to a
lack of mains voltage or a technical defect.
If damage (including consequential damage) can occur as a re-
sult of product failure, the following precautions can be taken
at your discretion:
• Installation of a water level dependent (under circumstanc-
es, mains-independent) alarm system, so that the alarm can
be heard before damage occurs.
• Inspection of the collecting tank/chamber for tightness up
to the top edge before – or at the latest, during – installation
or operation of the product.
• Installation of backow protection for drainage units that can
be damaged by wastewater leakage upon product failure.
• Installation of a further product that can compensate in
case of failure of the other product (e.g. duplex unit).
• Installation of an emergency power generator.
As these precautions serve to prevent or minimise conse-
quential damage upon product failure, they are to be strictly
observed as the manufacturer’s guideline – in line with the
standard DIN EN specications as state of the art – when using
the product (Higher Regional Court Frankfurt/Main, Ref.: 2 U
205/11, 06/15/2012).
SAFETY INSTRUCTIONS
This instruction manual contains essential information that
must be observed during installation, operation and servic-
ing. It is therefore important that the installer and the respon-
sible technician/operator read this instruction manual before
the equipment is installed and put into operation. The manual
must always be available at the location where the pump or the
plant is installed.
Failure to observe the safety instructions can lead to the loss
of all indemnity.
In this instruction manual, safety information is distinctly la-
belled with particular symbols. Disregarding this information
can be dangerous.
General danger to people
Warning of electrical voltage
NOTICE! NOTICE!
Danger to equipment and operation
Qualication and training of personnel
All personnel involved with the operation, servicing, inspection
and installation of the equipment must be suitably qualied
for this work and must have studied the instruction manual in
depth to ensure that they are suciently conversant with its
contents. The supervision, competence and areas of responsi-
bility of the personnel must be precisely regulated by the ope-
rator. If the personnel do not have the necessary skills, they
must be instructed and trained accordingly.
Safety-conscious working
The safety instructions in this instruction manual, the existing
national regulations regarding accident prevention, and any
internal working, operating and safety regulations must be ad-
hered to.
Safety instructions for the operator/user
All legal regulations, local directives and safety regulations
must be adhered to.
The possibility of danger due to electrical energy must be pre-
vented.
Leakages of dangerous (e.g. explosive, toxic, hot) substances
must be discharged such that no danger to people or the envi-
ronment occurs. Legal regulations must be observed.
Safety instructions for installation, inspection and mainte-
nance works
As a basic principle, works may only be carried out to the equip-
ment when it is shut down. Pumps or plant that convey harmful
substances must be decontaminated.
All safety and protection components must be re-tted and/or
made operational immediately after the works have been com-
pleted. Their effectiveness must be checked before restarting,
taking into account the current regulations and stipulations.
Unauthorised modications, manufacture of spare parts
The equipment may only be modied or altered in agreement
with the manufacturer. The use of original spare parts and
accessories approved by the manufacturer is important for
safety reasons. The use of other parts can result in liability for
consequential damage being rescinded.
7

Chat with your Jung Pumpen Multidrain UV 620-1 manual using AI

Get instant AI answers from your Jung Pumpen Multidrain UV 620-1 manual

Ask anything about the Jung Pumpen Multidrain UV 620-1. Answers come from this manual, with the pages they are based on.

Multidrain UV 620-1 Maintenance Schedule

Regularly
Clean the inlet strainer and float

Regular cleaning of the foot strainer and float prevents coarse dirt entry and ensures maximum pump performance.

Regularly
Check and clean ventilation hole in sealing plug

Inspect and clean the ventilation hole in the sealing plug of the unused discharge branch to ensure proper automatic venting.

Regularly
Inspect lifting gear for safety compliance

Lifting gear used to lower or raise the pump must be checked regularly by an expert in accordance with legal regulations.

M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend Multidrain UV 620-1?

Yes No

Frequently Asked Questions

A

The pump is designed to transport wastewater containing admixtures with a maximum grain size of 10 millimeters.

Is this answer helpful?

A

No, electrical work must only be performed by a qualified electrician to ensure safety and compliance with local regulations.

Is this answer helpful?

A

Running the pump dry can cause immediate motor damage. The built-in thermostat will shut it down, but prevention is key to avoiding repairs.

Is this answer helpful?

A

Check the startup jolt; it should oppose the arrow on the motor housing. Loud noises or low performance indicate wrong rotation requiring phase swap.

Is this answer helpful?

A

Yes, when stored in dry conditions, the pump is frost-resistant down to minus 20 degrees Celsius, but it must not freeze while installed in water.

Is this answer helpful?

A

The pump must be connected to a circuit protected by a 16 A slow-blow fuse and a residual current device with a trip current of 30 mA.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Handles solids up to 10 mm grain size effectively
  • Automatic thermal protection prevents motor burnout
  • Flexible discharge options with horizontal and vertical ports
  • Continuous operation possible with submerged yellow ring
  • Compact design fits standard sump pit dimensions
VS

Disadvantages

  • Requires professional electrical installation only
  • Cannot run dry without risking severe motor damage
  • Must be disconnected before clearing blockages due to auto-restart risk
  • Free cable end requires separate approved connector purchase
  • Limited to media temperatures below 40 degrees Celsius
M: QW-35-FL

Product Specification

Power

2400 W

Flow rate

9514 gph

Head height

60.7 ft

Pressure connection

2"

Features

without tank, IP68

Cable length

32.8 ft

Weight

50.71 lbs

M: QW-35-FL

Product Description

Jung Pumpen Multidrain UV 620-1: Reliable Sewage Handling

The Jung Pumpen Multidrain UV 620-1 Electro Submersible Sewage Pump is a robust solution designed for demanding drainage applications. This submersible pump belongs to the MultiDrain series, which is specifically engineered to handle wastewater, rainwater, groundwater, seepage water, and drainage water containing solid particles up to 10 mm in size. Its versatility makes it an ideal choice for residential basements, commercial buildings, and industrial sites where efficient water management is critical.

Constructed with durability in mind, this pump features a compact design that allows for easy installation in sump pits of various dimensions. The unit supports both horizontal and vertical discharge options, providing flexibility during setup. A key feature of the UV 620-1 is its ability to operate continuously as long as the yellow float ring remains submerged, ensuring consistent performance without interruption. However, running the pump dry must be strictly avoided to prevent motor damage, as the device includes a winding thermostat that automatically shuts off the unit if temperatures become dangerously high due to overload or dry running.

Safety is paramount in the design of the Jung Pumpen Multidrain UV 620-1. The pump is equipped with a thermal cut-off switch that protects the motor from overheating. It is crucial to disconnect the power supply before attempting to clear any blockages, as the pump may restart automatically once it cools down. Electrical connections must be performed by qualified professionals using circuits protected by at least a 16 A slow-blow fuse and a residual current device (RCD) rated at 30 mA. The pump handles media temperatures up to 40°C and can be stored in dry conditions at temperatures as low as -20°C without freezing.

Maintenance is straightforward but essential for longevity. Regular cleaning of the foot strainer prevents clogging and ensures optimal pumping efficiency. If the impeller becomes blocked by solids or fibrous matter, the strainer can be removed for inspection and cleaning. The pump also features a self-venting mechanism via a plug on the unused discharge port, simplifying operation. Whether used in a single installation with a guide rail system or as part of a duplex setup, the UV 620-1 delivers reliable performance when installed according to safety guidelines.

Important Notes

  • Always lift the pump by the handle, never by the power cable.
  • Ensure the pressure pipe is looped above the backflow level to prevent sewage backup.
  • Use only original spare parts to maintain warranty and safety standards.
  • Check rotational direction upon installation; incorrect rotation reduces efficiency and increases noise.
M: QW-35-FL

© Copyright 2026 Manual.ly