Hager TRB201 Manual
PDF manual · 4 Pages
English

Quick check
Incorrect answer, please try again.
Chat with your Hager TRB201 manual using AI
Get instant AI answers from your Hager TRB201 manual
Ask anything about the Hager TRB201. Answers come from this manual, with the pages they are based on.
Ask a Question
Do you recommend TRB201?
Yes NoFrequently Asked Questions
The TRB201 is a mains-powered wireless switching actuator for Tebis and KNX RF installations. It receives radio commands and switches one compatible electrical load on or off through its single relay output.
Is this answer helpful?
The actuator uses one 16 A, 230 V AC1 micro-gap contact. Load suitability also depends on the load type. For example, incandescent loads are rated up to 2300 W, while fluorescent and compact fluorescent loads have lower limits.
Is this answer helpful?
Yes. A T pushbutton on the actuator allows local manual operation of the output. The function LED shows relay status, with a red light indicating that the relay is closed.
Is this answer helpful?
The actuator supports Quicklink tool-free configuration, Tebis TX Easy configuration, and ETS3 or later commissioning through a compatible TR131x media coupler. Available functions depend on the selected setup and parameters.
Is this answer helpful?
Press and hold the R configuration pushbutton for more than 10 seconds until the configuration LED flashes, then release it. The LED turns off when the reset is complete. This deletes all existing configuration data.
Is this answer helpful?
For a load current above 10 A, use solid cable with a minimum conductor cross-section of 2.5 mm2. The actuator is intended to be protected upstream by a 16 A circuit breaker.
Is this answer helpful?
Advantages and Disadvantages
Advantages
- Single 16 A AC1 relay output supports dependable ON/OFF control of one electrical circuit.
- KNX RF operation at 868.3 MHz enables wireless control from compatible transmitters.
- Local T pushbutton and red status LED simplify testing, servicing, and manual override.
- Supports Quicklink, Tebis TX Easy, and ETS-based commissioning options.
- Compact flush-mounted format helps keep automation hardware discreet.
Disadvantages
- IP20 rating requires installation in a protected indoor enclosure or suitable flush-mounted location.
- It is an ON/OFF switching actuator and is not designed for dimming loads.
- Changing configuration modes requires a factory reset that erases all settings.
- Fluorescent and compact fluorescent load limits are substantially lower than the 16 A relay rating.
- Professional installation is required, and antenna placement can affect wireless performance.
Product Specification
Type
Actuator
Standard
KNX
Function
Switch actuator (on/off)
Topology
Bus
Dimensions
2.09 x 2.09 x 1.18 in
Product Description
Hager Wireless Output Flush-Mounted 1-gang, 16A, Switching Actuator - Read, Download & Print Free
The Hager Wireless Output Flush-Mounted 1-gang, 16A, Switching Actuator is a compact radio-controlled relay designed for reliable ON/OFF switching in Tebis and KNX RF installations. Identified as TRB201, this mains-powered receiver fits discreetly into flush-mounted locations while bringing wireless control to lighting and other compatible electrical loads. Its single independent output is suited to projects where dependable switching, local override, and flexible configuration are important.
Wireless switching with practical local control
Operating at 868.3 MHz, the actuator receives commands from compatible radio transmitters, including wall pushbuttons, remote controls, and other input devices. It switches one electrical circuit through a 16 A, 230 V AC1 micro-gap contact. This makes it a useful choice for automation upgrades where running new control wiring may be difficult or undesirable.
A dedicated T pushbutton provides manual control of the output directly at the unit. The function LED gives a clear visual indication of relay status: a red light means the relay is closed. These features are helpful during installation, commissioning, maintenance, or temporary manual operation.
Flexible commissioning for Tebis systems
The TRB201 supports several setup approaches, allowing it to suit different installation workflows. It can be configured through Quicklink tool-free commissioning, Tebis TX Easy configuration, or ETS3 and later through a compatible TR131x media coupler. The available behavior depends on the chosen configuration and parameter settings, giving installers the ability to tailor operation to the wider automation system.
If a new configuration method is required, the actuator can be restored to factory settings. Holding the R configuration pushbutton for more than 10 seconds starts the reset process and clears existing settings. After power-up or a factory reset, a 15-second wait is required before new commissioning begins.
Electrical and installation considerations
The actuator is supplied by 230 V, 50 Hz mains power and has an IP20 protection rating for indoor installation in suitable enclosed locations. Its compact dimensions of approximately 53 mm diameter by 30 mm depth support concealed mounting. Compatible load ratings include up to 2300 W for incandescent lamps, 1500 W for halogen lamps and transformers, and lower ratings for fluorescent and compact fluorescent loads.
Installation should be completed by a qualified electrician in accordance with local regulations. Keep the antenna as far as practical from the actuator and avoid mounting it immediately beside the controlled lamp. For loads above 10 A, use solid cable with a minimum 2.5 mm2 conductor cross-section. A 16 A upstream circuit breaker is specified.
Note: The Hager Wireless Output Flush-Mounted 1-gang, 16A, Switching Actuator is intended for switching, not dimming. Confirm load type, wiring conditions, and system compatibility before installation.
Search for 67,706 Manuals online
Type-in Brand or Model