Manual.ly Logo

Hager Radio Remote Control 4 Channel Manual

0.0 · 0 Ratings

PDF manual · 4 Pages

English

M: OA-GPT-5-NAN
page

/ 4

Loading...
8020f0bde39459ed6e9e1e62a64d38036fcc page 1
6LE003067A
TU402, TU404
Les télécommandes radio TU402, TU404 sont des
émetteurs qui permettent de piloter à distance, des
modules de sortie KNX. Ils font partie du système
d’installation Tebis. Ils permettent de piloter de l’éclai-
rage, des stores ou des volets roulants, du chauage,…
Fonctions
• 2 ou 4 voies indépendantes de commande par le bus KNX.
• Visualisation de l’émission d’un ordre.
• Verrouillage/déverrouillage des touches 2.
• Signalisation des fonctions par porte-étiquette 4.
Configuration
Ces émetteurs peuvent être configurés de 3 façons
diérentes :
•
quicklink
: configuration sans outil, voir notice
6T7952 livrée avec les récepteurs radio.
• TX100/B V.2.6.0 ou > : descriptif des fonctions du
produit disponible chez le constructeur.
• ETS3 ou > via TR131 : Base de données et descriptif du
logiciel d’application disponible chez le constructeur.
Configuration par TX100 ou ETS
Faites un appui sur le poussoir J lors de la phase
d’apprentissage par le TX100 ou pour l’adressage avec
le TR131 en ETS.
Utilisation des télécommandes avec concentrateur
d’entrées radio TR351 : voir page 2.
O
Pour changer de mode de configuration, il faut obliga-
toirement faire un “retour usine” du produit.
Mode verrouillage des touches
En mode verrouillage, les appuis sur les touches 2 sont
ignorés. Aucun ordre n'est émis.
Clonage d’émetteurs
Le clonage permet dupliquer un émetteur radio “maitre”
déjà configuré pour créer rapidement des copies
totalement identiques.
Spécifications techniques / Technische Daten / Technical characteristics / Technische kenmerken / Caratteristiche tecniche
A E Z I
Y
Alimentation Versorgungsspannung Supply voltage Voedingsspanning Tensione di alimentazione 2x CR 2430 3,0 V
(TBTS, SELV, ZLVS )
Fréquence d'émission
Sendefrequenz Transmission frequency Zendfrequentie Frequenza portante 868,3 MHz
Portée en champ libre
Reichweite im freien
Feld
Range in a free field Bereik Max distanza di trasmis-
sione in campo libero
100 m
Durée de vie approxi-
mative de la pile
Annähernde Lebens-
dauer der Batterie
Approximate life
duration of the battery
Geschate Levensduur
van de batterij
Durata di avvicina a vita
della batteria
5 ans / 5 Jahre / 5 years / 5 Jaar/
5 anni
Encombrement Abmessungen Dimensions Afmeting Ingombro 83 x 46,5 x 15,8 mm
Indice de protection Schutzart Degree of protection Beschermingsgraad Grado di protezione IP 50
T° de fonctionnement Betriebstemperatur Operating temperature Bedirijfstemperatuur T
a
di funzionamento -10 °C —> + 70 °C
T° de stockage Lagertemperatur Storage temperature Opslagtemperatuur T
a
di stoccaggio - 20 °C —> + 70 °C
Puissance d'émission
maximale
Maximale
Sendeleistung
Maximum emission
power
Maximaal emissiever-
mogen
Potenza massima di emis-
sione
25mW
Media de transmission
KNX RF
RF KNX
Übertragungsmedien
RF KNX
Communication Media
RF KNX communicatie-
media
Mezzo di comunicazione RF
KNX
RF1.R
Catégorie de réception Empfänger Kategorie Receiver category Ontvanger categorie Ricevitore categoria 2
Rapport cycle
d'émission
Einschaltdauer Sender Transmitter duty cycle Transmitter
arbeidscyclus
Ciclo di lavoro del
trasmettitore
1%
cfg
Die Fernbedienungen TU402 und TU404 sind Sender,
die zur Fernsteuerung der an den KNX angeschlossenen
Ausgangsmodule dienen. Diese Geräte gehören zum
Tebis-Installations-System. Sie dienen zur Steuerung der
Beleuchtung, der Markisen, der Rollläden, der Heizung usw.
Funktionen
• 2 oder 4 voneinander unabhängig Kanäle.
• LED zur Sendebestätigung.
• Ver-/ Entriegeln der Tasten
2
.
• Beschriftungsfeld 4.
Einstellungen
Diese Sender lassen sich auf 3 unterschiedliche Arten
konfigurieren :
•
quicklink
: Konfiguration ohne Werkzeug, siehe
Anleitung 6T7952 (mit den Funkempfängern mitgeliefert).
• TX100/B V.2.6.0 oder >: Beschreibung der
Gerätfunktionen beim Hersteller erhältlich.
• ETS3 oder > via TR131 : Datenbank und Beschreibung
der Anwendungssoftware beim Hersteller erhältlich.
Konfiguration über TX100 oder ETS
Taste J in der Lernphase des TX100 oder zur
Adressierung mittels TR131 in der ETS-Software drücken.
Verwendung der Fernbedienungen mit Funkeingangs-Hub
TR351: Siehe Seite 2.
O
Um den Konfigurationsmodus zu ändern, ist das Gerät
obligatorisch auf "Werkseinstellungen" zurückzusetzen.
Tasten-Verriegelungs-Modus
Im Verriegelungsmodus werden Betätigungen der Tasten
2 ignoriert. Es wird kein Steuerbefehl ausgegeben.
Sender klonen
Durch Klonen lässt sich ein bereits konfigurierter Master-
Funksender duplizieren. Auf diese Weise erhalten Sie
rasch vollkommen identische Kopien.
Vorgehensweise beim Klonen eines Senders
- Konfigurationsmodus durch Betätigung der Taste J des
“Master-Gerätes” aktivieren: Die LED cfg leuchtet auf.
- An dem zu klonenden Gerät, das noch die Werkseinstellungen
enthält, Taste cfg lang anhaltend drücken (über 15 Sek.), bis
die LED cfg die zweite Blinkstufe (schnelleres Blinken) erreicht.
Sobald die LED erlischt, ist das Klonen beendet. Wiederholen
Sie diesen Vorgang an den restlichen zu klonenden Geräten.
- Klon-Modus durch erneute Betätigung der Taste J des
Master-Gerätes drücken.
Der geklonte Sender identifiziert sich durch orangefarbenes
Aufleuchten der LED cfg bei Betätigung der Taste J.
O
Das Klonen ist nur möglich zwischen Sendern mit gleicher
Eingangsanzahl. Ein geklontes Gerät lässt sich nicht umpro-
grammieren. Dasselbe gilt für das Master-Gerät. Diese Geräte
müssen auf Werkseinstellungen zurückgesetzt und neu pro-
grammiert werden.
Zurücksetzen auf Werkseinstellungen
Taster J drücken und gedrückt halten, bis die LED cfg blinkt
(>10 Sekunden), dann loslassen. Die Rücksetzung auf
Werkseinstellungen wird durch das Erlöschen der LED cfg
Remote controls TU402 and TU404 are radio transmitters
used to remotely control the KNX-output modules. They
are part of the Tebis Installation System and make it pos-
sible to control lighting, blinds or rolling shutters, hea-
ting…
Functions
• 2 ou 4 independent control channels of bus KNX.
• Display of transmitted controls.
• Locking / unlocking of keys 2.
• A label holder 4 is used to signal the various functions.
Configuration
These transmitters may be configured in 3 dierent ways :
•
quicklink
: configuration without tool, see User's
Instructions 6T7952 supplied with the radio transmitters.
• TX100/B V.2.6.0 or >: Description of product features
is available from the Manufacturer.
• ETS3 or > via TR131 : Database and description of
software application available from the Manufacturer.
Configuration by TX100 or ETS
Press J pushbutton once at TX100 learning phase or
for addressing by using TR131 in ETS.
Use of remote controls with concentrator of TR351 radio
inputs: See page 2.
O
In order to change the configuration mode, a product
"factory reset" is required.
Key locking mode
In key locking mode, presses on keys 2 ignored.
No control is transmitted.
Cloning of transmitters
Cloning allows duplicating a "Master" radio transmitter
previously configured to create fully identical copies qui-
ckly.
How to clone a transmitter?
- Enter in configuration mode by pressing the J
pushbutton of the "Master": LED cfg turns on.
- On the product to be cloned still in factory mode, press J
pushbutton for an extended time (T>15s) until the 2nd flicke-
ring level (faster) of LED cfg is reached. When LED flickering
ends (LED turns o), cloning is completed.
Repeat this step for the other products to be cloned.
- Exit the cloning mode by pressing again Master J
push-button.
When pushbutton is pressed, LED cfg turns orange to signal
the cloned transmitter.
O
Cloning is possible only between transmitters with the same
number of inputs.
A cloned product cannot be modified, including the "Master".
The product shall be factory reset and reprogrammed.
Factory reset
Hold the J pushbutton depressed until cfg LED flickers
(>10s), then release it.
LED cfg turns o to signal the end of factory reset.
Signification de la LED 1
Action sur le produit Etat LED Couleur LED Signification
Appui simultané sur les
boutons poussoirs
3
Allumée fixe pendant 1 s Orange Le mode verrouillage est activé
Allumée fixe pendant 1 s Verte Le mode verrouillage est désactivé
Clignotante pendant 1 s Rouge Le niveau des piles est faible
Appui sur une des
touches
2
Allumée brièvement Verte L'ordre est émis
Clignotant pendant 1 s Orange Le BP actionné n'est pas configuré
Allumée brièvement Orange Le mode verrouillage est activé
Clignotante pendant 1 s Rouge Le niveau des piles est faible
Eteinte _ - Absence ou niveau de piles trop faible
- Non respect de la polarité des piles
Bedeutung der Kontrollleuchte 1
Betätigung des
Produkts
Zustand der LED Farbe der LED Bedeutung
Gleichzeitige Betätigung
der Drucktasten
3
Aufleuchten während
1 Sekunde
Orange Der Verriegelungs-Modus ist aktiviert
Grün Der Verriegelungs-modus ist deaktiviert
Blinkt 1 Sekunde lang Rot Der Batterieladezustand ist schwach
Betätigung einer der
Tasten 2
Leuchtet kurz auf Grün Der Steuerbefehl wird gesendet
Blinkt 1 Sekunde lang Orange Die betätigte Taste ist nicht konfiguriert
Leuchtet kurz auf Orange Der Verriegelungs-Modus ist aktiviert
Blinkt 1 Sekunde lang Rot Der Batterieladezustand ist schwach
Leuchtet nicht _ - Keine Batterien oder Batterieladezustand sehr schwach
- Batterien verpolt
Signal 1 indications
Operation by User LED state LED Color Indication
Simultaneous press on
3
keys
Switches on for 1 s Orange Key locking mode is activated
Switches on for 1 s Green Key locking mode is deactivated
Flashes on & o for 1s Red Low battery level
Pressing one of the
2 keys
Switches on for a short time Green Control is transmitted
Flashes on & o for 1s Orange The push-button pressed is not configured
Switches on for a short time Orange Key locking mode is activated
Flashes on & o for 1s Red Low battery level
O _ No batteries or very low battery level -
Batteries are not placed correctly -
Comment cloner un émetteur ?
- Entrer en configuration par un appui sur le poussoir cfg du
“maître” : Allumage LED cfg.
- Sur le produit à cloner encore en mode d’usine, faites un
appui très long (t >15s) sur le poussoir J jusqu’au 2ème
niveau de clignotement (plus rapide) de la LED cfg. Fin du
clonage à l’extinction de la LED.
Répéter cette étape sur les autres produits à cloner.
- Sortie du mode clonage par un nouvel appui sur le poussoir
J du maitre.
L’émetteur cloné est signalé par un allumage en orange de la
LED cfg sur appui du poussoir J.
O
Le clonage n'est possible qu’entre émetteurs disposant du
même nombre d’entrée.
Impossible de modifier un produit cloné y compris le
"maître", faites un retour usine et reprogrammer le produit.
Retour usine
Appuyer et maintenir le poussoir J jusqu’au clignotement
de la LED cfg (>10s) puis relâcher. La fin du retour usine est
signalée par l’extinction de la LED cfg.
Cette opération provoque l’eacement complet de la
configuration du produit, quel que soit le mode de
configuration. Après un changement de piles ou
un retour usine, attendre 15s avant de procéder à
une configuration.
Changement des piles
Démonter la trappe à pile en dévissant les vis 5.
Retirer les 2 piles et insérer les nouvelles en respectant
la polarité (toujours changer les 2 piles en même temps). .
Remonter la trappe à piles 6.
angezeigt. Bei dieser Operation wird die komplette
Konfiguration des Gerätes gelöscht, unabhängig vom
Konfigurationsmodus. Nach einem Batteriewechseln
der einer Rücksetzung auf Werkseinstellungen ist eine
Wartezeit von 15 Sekunden abzuwarten, bevor die
Konfiguration vorgenommen werden kann.
Batterien auswechseln
Batteriefachdeckel mittels Schraubendreher demontieren.
Entfernen Sie die 2 Batterien und legen Sie die neuen
Batterien ein. Hierbei ist auf korrekte Polung zu achten
(es sind stets beide Batterien gleichzeitig zu wechseln).
Deckel des Batteriefachs 6 wieder einbauen.
This operation removes the entire product configuration,
whatever the mode of configuration. After a battery
change or a factory reset, wait 15s before proceeding to
configuration.
Replacement of batteries
Pull up the cover of the battery compartment by
unscrewing screws 5 Remove the 2 batteries and insert
the new ones making sure that matching of poles (+/-) is
correct (both batteries must be changed). Place battery
cover 6 back on.
¢
Télécommandes radio 2 et 4 voies
£
Funkfernbedienung 2 und 4 Kanäle
Z
2 and 4-channel radio frequency
remote controls
•
RF-afstandsbedieningen 2, 4 - kanalen
Telecomandi R.F. 2, 4 canali
6LE003067A1
6LE003067A2
A Notice d’instructions
E Bedienungsanleitung
Z User instructions
RFTP
230V
Bus
30 V
V2.6.0
ou >
Utilisable partout en Europe å et en Suisse
Par la présente Hager Controls déclare que l‘émetteur/
récepteur radio est conforme à la directive 2014/53/UE.
La déclaration CE peut être consultée sur le site :
www.hagergroup.net
Kann in ganz Europa å und in der Schweiz
Hiermit erklärt Hager Controls, dass der Funksender/-
Empfänger der 2014/53/UE Richtlinie entspricht.
Die EG-Erklärung kann auf der Website eingesehen werden:
www.hagergroup.net
Can be used throughout Europe å and in Switzerland
Hager Controls hereby declares that the radio transmitter/
receiver complies with the 2014/53/UE directive.
The EC declaration may be consulted on the website:
www.hagergroup.net

Chat with your Hager Radio Remote Control 4 Channel manual using AI

Get instant AI answers from your Hager Radio Remote Control 4 Channel manual

Ask anything about the Hager Radio Remote Control 4 Channel. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend Radio Remote Control 4 Channel?

Yes No

Frequently Asked Questions

A

The Hager TU402/TU404 series is available in 2- and 4-channel versions, providing independent KNX control channels for lighting, blinds, shutters or heating.

Is this answer helpful?

A

You can configure the transmitter via quicklink (tool-free), TX100 (TX100/B v2.6.0 or later) or ETS3 using TR131. For TX100/ETS learning, press the J pushbutton during the learning phase.

Is this answer helpful?

A

Enter master configuration with the J button to start cloning. On a factory-reset unit, hold J >15s until faster LED blinking; when LED turns off cloning is complete. To factory-reset, hold J until cfg LED blinks (>10s) then release.

Is this answer helpful?

A

The remote uses two CR2430 3.0V batteries. Replace both batteries simultaneously, respecting polarity. After replacing batteries or performing a factory reset, wait 15 seconds before reconfiguring.

Is this answer helpful?

A

Green briefly: control transmitted. Orange steady: lock mode active. Orange blink: pressed button not configured. Red blink: low battery. No LED: no batteries or very low battery/polarity issue.

Is this answer helpful?

A

Yes. Reset the remote to factory mode if needed, start the TR351 learning procedure, long-press the first key (>5s) until the red transmit LED lights, then press the keys to be learned sequentially.

Is this answer helpful?

A

The unit transmits at 868.3 MHz with a maximum free-field range of about 100 meters; actual indoor range may be lower depending on obstacles and building layout.

Is this answer helpful?

M: OA-GPT-5-NAN

Advantages and Disadvantages

Advantages

  • Multi-mode configuration: quicklink, TX100 and ETS3 for flexible installation.
  • Long battery life (~5 years) using two CR2430 3.0V cells.
  • Distinct LED feedback for transmission, lock/unlock and low battery.
  • Cloning feature enables fast duplication of preconfigured masters.
  • Compact dimensions and wide operating temperature (-10 °C to +70 °C).
VS

Disadvantages

  • Cloned units cannot be reprogrammed without performing a factory reset.
  • Switching configuration modes mandates a complete factory reset.
  • Free-field range of 100 m can be significantly reduced in buildings.
  • Protection rating IP50 gives limited dust protection and no water resistance.
  • Requires knowledge of TX100/ETS/TR351 procedures for proper integration.
M: OA-GPT-5-NAN

Product Specification

Type

Remote control

Standard

KNX

Function

Control

Topology

Bus, Tree

Dimensions

5.28x1.97x0.63in

Special features

IP30, battery-operated (2x CR2430)

M: OA-GPT-54-NAN

Product Description

Hager Radio Remote Control 4 Channel — Reliable KNX Radio Remote

The Hager Radio Remote Control 4 Channel (TU402/TU404) is a compact, battery-powered RF transmitter designed to operate KNX output modules wirelessly. Available in 2- and 4-channel versions, it integrates into Tebis installation systems to control lighting, blinds, roller shutters and heating. With a clear LED feedback system, tactile keys and a label holder for function identification, the unit balances simplicity and professional features for smart-home and building automation projects.

Key features and usage

The remote supports three configuration methods: quicklink (tool-free), TX100 (TX100/B v2.6.0 or later) and ETS3 (via TR131). These options let installers pair the transmitter to KNX-actuators or a TR351 radio-input concentrator depending on the project scale. For TX100/ETS address learning, press the J pushbutton during the learning phase. Changing configuration mode requires a factory reset.

Operation is intuitive: each channel emits a KNX order with a brief green LED confirmation. The device offers a lock mode that disables key presses to avoid accidental commands, indicated by a steady orange LED. Battery level and configuration errors are displayed via specific LED colors and blink patterns.

Technical highlights

Powered by two CR2430 3.0V batteries, the remote transmits at 868.3 MHz with a free-field range up to 100 m and an expected battery life of about 5 years under normal use. It measures 83 x 46.5 x 15.8 mm, carries an IP50 rating, and operates between -10 °C and +70 °C. Maximum RF output is 25 mW; transmitter duty cycle is 1%.

Advanced functions

Cloning lets you duplicate a configured master transmitter to create identical copies quickly (only between units with the same number of inputs). Cloned units cannot be reprogrammed without a factory reset of the device. For TR351 integration, put the remote in factory mode (hold J 10–15s), start learning on TR351, then long-press the first key (>5s) until the red transmit LED lights and sequentially press keys to learn.

Practical notes

  • After battery replacement or factory reset, wait 15 seconds before reconfiguring.
  • Always replace both batteries simultaneously and observe polarity.
  • Cloning requires the master and clones to have the same input count; cloned devices preserve the master configuration until reset.

Pros and Cons

Pros:

  • Easy multi-mode configuration: quicklink, TX100, ETS3.
  • Long battery life (~5 years) with CR2430 cells.
  • Clear LED feedback for transmission, lock state and battery status.
  • Supports cloning for rapid mass deployment of identical remotes.
  • Compact, durable design with wide operating temperature range.

Cons:

  • Cloned units cannot be reprogrammed without factory reset.
  • Configuration-mode changes require a full factory reset.
  • Limited free-field range (100 m) may be reduced indoors.
  • IP50 offers limited protection against dust and no water ingress rating.
  • Requires correct pairing procedures for TR351 and ETS tools.

Notes:

  • Use only CR2430 batteries and change both at once.
  • Wait 15s after battery change or reset before reconfiguring.
  • Cloning and factory reset procedures rely on the J pushbutton and LED cfg signals.
M: OA-GPT-5-NAN

© Copyright 2026 Manual.ly