GYS GYSMI E160 Manual
5.0 · 3 Ratings
PDF manual · 56 Pages
English
Loading...

12
GYSMI E160
MADE IN FRANCE
EN
The surface of the area to be considered around the device depends on the the building’s structure and other activities
that take place there. The area taken in consideration can be larger than the limits determined by the companies.
Welding area assessment
Besides the welding area, the assessment of the arc welding systems intallation itself can be used to identify and resolve
cases of disturbances. The assessment of emissions must include in situ measurements as specied in Article 10 of
CISPR 11: 2009. In situ measurements can also be used to conrm the effectiveness of mitigation measures.
RECOMMENDATION ON METHODS OF ELECTROMAGNETIC EMISSIONS REDUCTION
a. National power grid: The arc welding machine must be connected to the national power grid in accordance with
the manufacturer’s recommendation. If interferences occur, it may be necessary to take additional preventive measures
such as the ltering of the power suplly network. Consideration should be given to shielding the power supply cable in a
metal conduit. It is necessary to ensure the shielding’s electrical continuity along the cable’s entire length. The shielding
should be connected to the welding current’s source to ensure good electrical contact between the conduct and the
casing of the welding current source.
b. Maintenance of the arc welding equipment: The arc welding machine should be be submitted to a routine
maintenance check according to the manufacturer’s recommendations. All accesses, service doors and covers should be
closed and properly locked when the arc welding equipment is on.. The arc welding equipment must not be modied
in any way, except for the changes and settings outlined in the manufacturer’s instructions. The spark gap of the arc
start and arc stabilization devices must be adjusted and maintained according to the manufacturer’s recommendations.
c. Welding cables: Cables must be as short as possible, close to each other and close to the ground, if not on the
ground.
d. Electrical bonding : consideration shoud be given to bonding all metal objects in the surrounding area. However,
metal objects connected to the workpiece increase the riskof electric shock if the operator touches both these metal
elements and the electrode. It is necessary to insulate the operator from such metal objects.
e. Earthing of the welded part : When the part is not earthed - due to electrical safety reasons or because of its size
and its location (which is the case with ship hulls or metallic building structures), the earthing of the part can, in some
cases but not systematically, reduce emissions It is preferable to avoid the earthing of parts that could increase the risk
of injury to the users or damage other electrical equipment. If necessary, it is appropriate that the earthing of the part
is done directly, but in some countries that do not allow such a direct connection, it is appropriate that the connection
is made with a capacitor selected according to national regulations.
f. Protection and plating : The selective protection and plating of other cables and devices in the area can reduce
perturbation issues. The protection of the entire welding area can be considered for specic situations.
TRANSPORT AND TRANSIT OF THE WELDING MACHINE
Do not use the cables or torch to move the machine. The welding equipment must be moved in an
upright position.
Do not place/carry the unit over people or objects. Never lift the machine while there is a gas cylinder
on the support shelf. A clear path is available when moving the item.
EQUIPMENT INSTALLATION
• Put the machine on the oor (maximum incline of 10°.)
• Ensure the work area has sufcient ventillation for welding, and that there is easy access to the control panel.
• The machine must not be used in an area with conductive metal dusts.
• The machine must be placed in a sheltered area away from rain or direct sunlight.
• The machine protection level is IP21, which means :
- Protection against acess to dangerous parts from solid bodies of a ≥12.5mm diameter and,
- Protection against vertically falling drops.
The manufacturer does not incur any responsability regarding damages to both objects and persons
that result from an incorrect and/or dangerous use of the machine.
MAINTENANCE / RECOMMENDATIONS
• Maintenance should only be carried out by a qualied person. Annual maintenance is recommended.
• Ensure the machine is unplugged from the mains, and wait for two minutes before carrying out main-
tenance work. DANGER High Voltage and Currents inside the machine.
• Remove the casing 2 or 3 times a year to remove any excess dust. Take this opportunity to have the
electrical connections checked by a qualied person, with an insulated tool.
• Regularly check the condition of the power supply cable. If the power cable is damaged, it must be
replaced by the manufacturer, its after sales service or an equally qualied person.
• Ensure the ventilation holes of the device are not blocked to allow adequate air circulation.
• Do not use this equipment to thaw pipes, to charge batteries, or to start any engine.
Quick check
I'm not a robot
Incorrect answer, please try again.
Chat with your GYS GYSMI E160 manual using AI
Get instant AI answers from your GYS GYSMI E160 manual
Ask anything about the GYS GYSMI E160. Answers come from this manual, with the pages they are based on.
GYSMI E160 Maintenance Schedule
Remind me when maintenance is due
M: QW-35-FL
Interval
Maintenance task
In the manual
Every 4 months
Clean internal dust
Remove the casing 2 or 3 times a year to remove excess dust using an air blower.
Show in the manual
(page 12)
Every 4 months
Check electrical connections
Take this opportunity to have electrical connections checked by a qualified person with an insulated tool.
Show in the manual
(page 12)
Yearly
Annual maintenance check
Maintenance should only be carried out by a qualified person. Annual maintenance is recommended.
Show in the manual
(page 6)
Free maintenance reminders
Timed to your purchase date. Always free, unsubscribe anytime.
Ask a Question
0/1000
Do you recommend GYSMI E160?
Yes NoProduct Specification
Power
6kW (230V)
No-load voltage
72V
Control range
10-160A (MMA/TIG)
Electrodes
0.06-0.16in (MMA)
Protection class
IP21
Dimensions
8.27x10.63x4.72in (HxWxD)
Weight
10.14lb
Product Description
Search for 67,706 Manuals online
Type-in Brand or Model
Lukas Schmitz
10 months ago
On my iE160 the manual says I can change the Arc Force value, but the knob/menu for it is not available. What should I do, and how do I set the right current for my electrode?
Manual.ly
10 months ago
For the iE160, the Arc Force adjustment described in some manuals is not available as a separate setting on the unit (it is fixed by design). You can still get good results by setting the correct welding current for your electrode and material thickness. Also, the current table on the inverter is a guideline; for some electrode types you may need to choose a slightly higher current than the table value to achieve stable arc ignition and smooth weld beads. If possible, start with a small test weld and fine-tune the current until the arc sounds stable and penetration looks right.