GYS GYSMI E160 Manual
5.0 · 3 Ratings
PDF manual · 56 Pages
English
Loading...

9
GYSMI E160
MADE IN FRANCE
EN
WARNING - SAFETY RULES
GENERAL INSTRUCTIONS
Read and understand the following safety recommendations before using or servicing the unit.
Any change or servicing that is not specied in the instruction manual must not be undertaken.
The manufacturer is not liable for any injury or damage caused due to non-compliance with the instructions featured
in this manual .
In the event of problems or uncertainties, please consult a qualied person to handle the installation properly.
ENVIRONMENT
This equipment must only be used for welding operations in accordance with the limits indicated on the descriptive panel
and/or in the user manual. The operator must respect the safety precautions that apply to this type of welding. In case
of inedaquate or unsafe use, the manufacturer cannot be held liable for damage or injury.
This equipment must be used and stored in a place protected from dust, acid or any other corrosive agent. Operate the
machine in an open, or well-ventilated area.
Operating temperature:
Use between -10 and +40°C (+14 and +104°F).
Store between -20 and +55°C (-4 and 131°F).
Air humidity:
Lower or equal to 50% at 40°C (104°F).
Lower or equal to 90% at 20°C (68°F).
Altitude:
Up to 1000 meters above sea level (3280 feet).
INDIVIDUAL PROTECTIONS AND OTHERS
Arc welding can be dangerous and can cause serious and even fatal injuries.
Welding exposes the user to dangerous heat, arc rays, electromagnetic elds, noise, gas fumes, and electrical shocks.
People wearing pacemakers are advised to consult with their doctor before using this device.
To protect oneself as well as the other, ensure the following safety precautions are taken:
In order to protect you from burns and radiations, wear clothing without cuffs. These clothes must be
insulated, dry, reproof and in good condition, and cover the whole body.
Wear protective gloves which guarantee electrical and thermal insulation.
Use sufcient welding protective gear for the whole body: hood, gloves, jacket, trousers... (varies depen-
ding on the application/operation). Protect the eyes during cleaning operations. Do not operate whilst
wearing contact lenses.
It may be necessary to install reproof welding curtains to protect the area against arc rays, weld spatters
and sparks.
Inform the people around the working area to never look at the arc nor the molten metal, and to wear
protective clothes.
Ensure ear protection is worn by the operator if the work exceeds the authorised noise limit (the same
applies to any person in the welding area).
Stay away from moving parts (e.g. engine, fan...) with hands, hair, clothes etc...
Never remove the safety covers from the cooling unit when the machine is plugged in - The manufac-
turer is not responsible for any accident or injury that happens as a result of not following these safety
precautions.
The pieces that have just been welded are hot and may cause burns when manipulated. During mainte-
nance work on the torch or the electrode holder, you should make sure it’s cold enough and wait at least
10 minutes before any intervention. The cooling unit must be on when using a water cooled torch in order
to ensure that the liquid does not cause any burns.
ALWAYS ensure the working area is left as safe and secure as possible to prevent damage or accidents.
Quick check
I'm not a robot
Incorrect answer, please try again.
Chat with your GYS GYSMI E160 manual using AI
Get instant AI answers from your GYS GYSMI E160 manual
Ask anything about the GYS GYSMI E160. Answers come from this manual, with the pages they are based on.
GYSMI E160 Maintenance Schedule
Remind me when maintenance is due
M: QW-35-FL
Interval
Maintenance task
In the manual
Every 4 months
Clean internal dust
Remove the casing 2 or 3 times a year to remove excess dust using an air blower.
Show in the manual
(page 12)
Every 4 months
Check electrical connections
Take this opportunity to have electrical connections checked by a qualified person with an insulated tool.
Show in the manual
(page 12)
Yearly
Annual maintenance check
Maintenance should only be carried out by a qualified person. Annual maintenance is recommended.
Show in the manual
(page 6)
Free maintenance reminders
Timed to your purchase date. Always free, unsubscribe anytime.
Ask a Question
0/1000
Do you recommend GYSMI E160?
Yes NoProduct Specification
Power
6kW (230V)
No-load voltage
72V
Control range
10-160A (MMA/TIG)
Electrodes
0.06-0.16in (MMA)
Protection class
IP21
Dimensions
8.27x10.63x4.72in (HxWxD)
Weight
10.14lb
Product Description
Search for 67,706 Manuals online
Type-in Brand or Model
Lukas Schmitz
10 months ago
On my iE160 the manual says I can change the Arc Force value, but the knob/menu for it is not available. What should I do, and how do I set the right current for my electrode?
Manual.ly
10 months ago
For the iE160, the Arc Force adjustment described in some manuals is not available as a separate setting on the unit (it is fixed by design). You can still get good results by setting the correct welding current for your electrode and material thickness. Also, the current table on the inverter is a guideline; for some electrode types you may need to choose a slightly higher current than the table value to achieve stable arc ignition and smooth weld beads. If possible, start with a small test weld and fine-tune the current until the arc sounds stable and penetration looks right.