GYS GYSMI 80P Manual
5.0 · 1 Ratings
PDF manual · 40 Pages
English
Loading...

7
GYSMI 80P 130P 160P 200P
MADE IN FRANCE
EN
WARNING - SAFETY RULES
GENERAL INSTRUCTIONS
Read and understand the following safety recommendations before using or servicing the unit.
Any change or servicing that is not specied in the instruction manual must not be undertaken.
The manufacturer is not liable for any injury or damage due to non-compliance with the instructions featured in this
manual .
In the event of problems or uncertainty, please consult a qualied person to handle the inspection properly.
ENVIRONMENT
This equipment must only be used for welding operations in accordance with the limits indicated on the descriptive panel
and/or in the user manual. The operator must respect the safety precautions that apply to this type of welding. In cases
of inedaquate or unsafe use, the manufacturer cannot be held liable.
This equipment must be used and stored in a place protected from dust, acid or any other corrosive agent. Operate the
machine in an open, or well-ventilated area.
Operating temperature:
Use between -10 and +40°C (+14 and +104°F).
Store between -25 and +55°C (-13 and 131°F).
Air humidity:
Lower or equal to 50% at 40°C (104°F).
Lower or equal to 90% at 20°C (68°F).
Up to 2000 meters above sea level (6500 feet).
INDIVIDUAL PROTECTIONS AND OTHERS
Welding exposes the user to dangerous heat, arc rays, electromagnetic elds, noise, gas fumes, and electrical shocks.
People wearing pacemakers are advised to consult with their doctor before using this device.
In order to protect you from burns and radiation, wear clothing with long sleeves. These clothes must be
insulated, dry, reproof and in good condition, and cover the whole body.
Wear protective gloves which guarantee electrical and thermal insulation.
It may be necessary to install reproof welding curtains to protect others against arc rays, weld spatter
and sparks.
Inform the people around the working area to never look at the arc ray or the molten metal, and to wear
protective clothes.
It is necessary to protect yourself with a welding hood (rated NR.10 or higher) and to protect your eyes
during cleaning operations.
Do not operate whilst wearing contact lenses.
Ensure ear protection is worn by the operator if the work exceeds the authorised noise limit. Ensure ear
protection is worn by anyone in the welding area .
Keep hands, hair, clothes etc... away from moving parts (e.g. fan)
Never remove the safety cover of the wire feeder when the machine is plugged in - The manufacturer is
not responsible for any accident or injury that happens as a result of not following these safety precau-
tions.
The pieces that have just been welded are hot and may cause burns when touched.
During maintenance work on the torch or electrode holder, you should make sure it’s cold enough and
wait at least 10 minutes before any intervention. ALWAYS ensure the working area is left as safe and
secure as possible to prevent damage or accidents.
WELDING FUMES AND GAS
The fumes, gases and dust produced during welding are hazardous. It is mandatory to ensure adequate
ventilation and/or extraction to keep fumes and gases away from the work area. An air fed helmet is
recommended in cases of insufcient air supply in the workplace.
Check that the air intake is in compliance with safety standards
Quick check
I'm not a robot
Incorrect answer, please try again.
Chat with your GYS GYSMI 80P manual using AI
Get instant AI answers from your GYS GYSMI 80P manual
Ask anything about the GYS GYSMI 80P. Answers come from this manual, with the pages they are based on.
GYSMI 80P Maintenance Schedule
Remind me when maintenance is due
M: QW-35-FL
Interval
Maintenance task
In the manual
Every 4 months
Remove casing and clean dust
Remove the casing 2 or 3 times a year to remove excess dust using an air blower.
Show in the manual
(page 10)
Every 4 months
Check electrical connections
Have a qualified person check the tightness of electrical connections with an insulated tool while cleaning.
Show in the manual
(page 10)
Free maintenance reminders
Timed to your purchase date. Always free, unsubscribe anytime.
Ask a Question
0/1000
Do you recommend GYSMI 80P?
Yes NoProduct Specification
Power
3 kW (230 V)
Open circuit voltage
85 V
Control range
10-80 A (MMA)
Electrodes
0.06-0.10 in (MMA)
Dimensions
5.51x9.06x3.94 in (HxWxD)
Weight
5.51 lb
Product Description
Search for 67,706 Manuals online
Type-in Brand or Model
Novella Ledner
8 months ago
Does the welding arc stay stable and the welding power stay constant during operation, or is it likely to fluctuate?
Manual.ly
8 months ago
Based on customer testing and product behavior, the arc stability is designed to remain consistent, so you should see a steady arc and reliable performance during normal welding. One reviewer reported constant welding power and perfect arc stability during their test, matching the expected results when using the recommended settings and proper setup. For best results, ensure you select the correct process and parameters for your material and electrode/wire, use suitable cables and a secure earth connection, and keep within the device rating (duty cycle) during longer work sessions.