Manual.ly Logo

GYS GYSMI 130P Manual

0.0 · 0 Ratings

PDF manual · 49 Pages

English

M: QW-35-FL
page

/ 49

Loading...
10bdc9a6b9967fee89b3486436328f8e6357 page 8
8
GYSMI 80P 130P 160P 200P
MADE IN FRANCE
EN
WARNING - SAFETY RULES
GENERAL INSTRUCTIONS
Read and understand the following safety recommendations before using or servicing the unit.
Any change or servicing that is not specied in the instruction manual must not be undertaken.
The manufacturer is not liable for any injury or damage caused due to non-compliance with the instructions featured
in this manual .
In the event of problems or uncertainties, please consult a qualied person to handle the installation properly.
ENVIRONMENT
This equipment must only be used for welding operations in accordance with the limits indicated on the descriptive panel
and/or in the user manual. The operator must respect the safety precautions that apply to this type of welding. In case
of inedaquate or unsafe use, the manufacturer cannot be held liable for damage or injury.
This equipment must be used and stored in a place protected from dust, acid or any other corrosive agent. Operate the
machine in an open, or well-ventilated area.
Operating temperature:
Use between -10 and +40°C (+14 and +104°F).
Store between -20 and +55°C (-4 and 131°F).
Air humidity:
Lower or equal to 50% at 40°C (104°F).
Lower or equal to 90% at 20°C (68°F).
Altitude:
Up to 1000 meters above sea level (3280 feet).
INDIVIDUAL PROTECTIONS AND OTHERS
Arc welding can be dangerous and can cause serious and even fatal injuries.
Welding exposes the user to dangerous heat, arc rays, electromagnetic elds, noise, gas fumes, and electrical shocks.
People wearing pacemakers are advised to consult with their doctor before using this device.
To protect oneself as well as the other, ensure the following safety precautions are taken:
In order to protect you from burns and radiations, wear clothing without cus. These clothes must be
insulated, dry, reproof and in good condition, and cover the whole body.
Wear protective gloves which guarantee electrical and thermal insulation.
Use sucient welding protective gear for the whole body: hood, gloves, jacket, trousers... (varies depen-
ding on the application/operation). Protect the eyes during cleaning operations. Do not operate whilst
wearing contact lenses.
It may be necessary to install reproof welding curtains to protect the area against arc rays, weld spatters
and sparks.
Inform the people around the working area to never look at the arc nor the molten metal, and to wear
protective clothes.
Ensure ear protection is worn by the operator if the work exceeds the authorised noise limit (the same
applies to any person in the welding area).
Stay away from moving parts (e.g. engine, fan...) with hands, hair, clothes etc...
Never remove the safety covers from the cooling unit when the machine is plugged in - The manufac-
turer is not responsible for any accident or injury that happens as a result of not following these safety
precautions.
The pieces that have just been welded are hot and may cause burns when manipulated. During mainte-
nance work on the torch or the electrode holder, you should make sure it’s cold enough and wait at least
10 minutes before any intervention. The cooling unit must be on when using a water cooled torch in order
to ensure that the liquid does not cause any burns.
ALWAYS ensure the working area is left as safe and secure as possible to prevent damage or accidents.

Chat with your GYS GYSMI 130P manual using AI

Get instant AI answers from your GYS GYSMI 130P manual

Ask anything about the GYS GYSMI 130P. Answers come from this manual, with the pages they are based on.

GYSMI 130P Maintenance Schedule

Remind me when maintenance is due
Yearly
Perform annual maintenance check

Maintenance should only be carried out by a qualified person. Annual maintenance is recommended to ensure safety and proper function.

2-3 times per year
Clean internal dust from casing

Remove the casing 2 or 3 times a year to remove excess dust using a blower. Ensure power is disconnected and wait two minutes before opening.

Show in the manual (page 12)
During cleaning
Check electrical connections

While cleaning the interior, have a qualified person check the tightness of electrical connections using an insulated tool.

Show in the manual (page 12)
Regularly
Inspect power supply cable

Regularly check the condition of the power supply cable. If damaged, it must be replaced by the manufacturer or a qualified person.

Show in the manual (page 12)

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend GYSMI 130P?

Yes No

Frequently Asked Questions

A

Yes, the machine can operate with generators as long as the auxiliary power meets specific requirements. The voltage must be alternating and set correctly with peak values below 400V, and the frequency should be between 50 and 60 Hz. Always verify these conditions to prevent damage from high voltage spikes.

Is this answer helpful?

A

The GYSMI 130P supports all common electrode types including rutile, stainless steel, cast iron, and basic low-hydrogen electrodes. It provides direct current output suitable for manual metal arc (MMA) welding applications.

Is this answer helpful?

A

No, this equipment is classified as Class A and is not intended for residential sites connected to public low-voltage networks. It may cause electromagnetic interference in homes. It is best suited for industrial or commercial environments.

Is this answer helpful?

A

If both indicators are on but no current flows, the thermal protection has likely triggered due to overheating. Wait for the cooling cycle to complete. If only the green light is on, check the earth clamp and electrode holder connections for faults.

Is this answer helpful?

A

The manufacturer provides a two-year warranty covering defects in workmanship and materials from the date of purchase. This covers parts and labor but excludes normal wear, transport damage, misuse, or environmental failures like rust and dust.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Includes a durable carrying case for safe transport and storage
  • Compatible with generator power sources up to 230V +/- 15%
  • Features Hot Start, Arc Force, and Anti-Sticking technologies
VS

Disadvantages

  • Class A EMC rating limits use in residential low-voltage areas
  • Requires annual professional maintenance for optimal safety
  • Not suitable for TIG welding without additional optional accessories
M: QW-35-FL

Product Specification

Power

4kW (230V)

Open Circuit Voltage

72V

Control Range

10-130A (WIG/MMA)

Electrodes

0.06-0.13in (MMA)

Protection Class

IP21

Dimensions

3.94x9.84x6.69in (HxDxW)

Weight

6.39lbs

M: QW-35-FL

Product Description

GYS GYSMI 130P Inverter Welding Machine with Case - Read, Download & Print Free

The GYS GYSMI 130P Inverter Welding Machine with Case represents a pinnacle of portable welding technology designed for professionals and serious enthusiasts who demand reliability in the field. Manufactured in France, this robust unit combines advanced inverter technology with a compact design that fits perfectly into its included carrying case. It is engineered to handle a wide variety of electrode types, including rutile, stainless steel, cast iron, and basic electrodes, making it a versatile tool for diverse repair and fabrication tasks.

This machine operates on standard single-phase 230V power but includes specific protections that allow it to function effectively with generators, provided the voltage peaks remain under 400V. The unit features three specialized inverter functions: Hot Start, which delivers an initial surge of current to ensure easy arc ignition; Arc Force, which automatically adjusts voltage to prevent the electrode from sticking when the arc length changes; and Anti-Sticking technology, which safely breaks the circuit if the electrode adheres to the workpiece. These features significantly improve weld quality and ease of use.

Safety is paramount in the design of the GYSMI 130P. The machine meets Class A electromagnetic compatibility standards, meaning it is intended for industrial or commercial environments rather than residential areas where sensitive electronics might be affected by interference. Users must adhere to strict safety protocols regarding ventilation, personal protective equipment, and electrical grounding. The device includes thermal protection that shuts down the unit if overheating occurs, requiring a cool-down period before resuming work. Regular maintenance involves cleaning dust from the interior and checking cable integrity, ensuring long-term durability.

Whether you are working on construction sites, in workshops, or traveling for freelance projects, the inclusion of a dedicated case ensures your investment remains protected during transit. The clear interface allows for precise current adjustment via a simple potentiometer, while the IP21 rating offers basic protection against solid objects and vertical water drops. This comprehensive package makes the GYSMI 130P a reliable choice for high-quality MMA welding operations.

M: QW-35-FL

© Copyright 2026 Manual.ly