Manual.ly Logo

Grundfos Unilift CC Manual

0.0 · 0 Ratings

PDF manual · 16 Pages

English

M: QW-35-FL
page

/ 16

Loading...
733266de7612ef8b7928dfb7fdac237cad54 page 9
Deutsch (DE)
9
5. Servicearbeiten am Produkt
5.1 Warten des Produkts
Unter normalen Betriebsbedingungen ist die Pumpe
wartungsfrei.
Wird die Pumpe jedoch nicht zum Fördern von sau-
berem Wasser, sondern zum Fördern anderer
Medien verwendet, muss sie unmittelbar nach dem
Gebrauch mit sauberem Wasser durchgespült wer-
den.
5.1.1 Vorgehensweise
Reinigen des Zulaufsiebs
1. Schalten Sie die Stromversorgung zur Pumpe ab.
2. Entleeren Sie die Pumpe.
3. Lockern Sie das Zulaufsieb. Schieben Sie einen
Schraubendreher zwischen das Pumpengehäuse
und das Zulaufsieb und drehen Sie ihn.
4. Reinigen Sie das Zulaufsieb und montieren Sie
es wieder.
Reinigen des Laufrads
1. Schalten Sie die Stromversorgung zur Pumpe ab.
2. Lockern Sie das Zulaufsieb. Schieben Sie einen
Schraubendreher zwischen das Pumpengehäuse
und das Zulaufsieb und drehen Sie ihn.
3. Nehmen Sie den unteren Teil ab.
Abb. 17 Entfernen des unteren Teils
4. Entfernen und reinigen Sie die Membran.
5. Spülen Sie die Pumpe mit sauberem Wasser
durch, um eventuelle Verschmutzungen zwi-
schen Motor und Pumpengehäuse zu entfernen.
Reinigen Sie das Laufrad.
6. Überprüfen Sie, ob sich das Laufrad ungehindert
drehen kann.
7. Bauen Sie die Pumpe in umgekehrter Reihen-
folge wieder zusammen.
5.2 Servicesätze
Diese Teile können ausgewechselt werden:
Die Teile können bei Ihrem Pumpenlieferanten
bestellt werden.
Falls andere Teile der Pumpe beschädigt oder defekt
sind, wenden Sie sich bitte an Ihren Pumpenlieferan-
ten.
GEFAHR
Stromschlag
Tod oder ernsthafte Personenschäden
- Schalten Sie die Stromversorgung ab,
bevor Sie Arbeiten am Produkt begin-
nen. Stellen Sie sicher, dass die Strom-
versorgung nicht versehentlich wieder
eingeschaltet werden kann.
GEFAHR
Stromschlag
Tod oder ernsthafte Personenschäden
- Ein beschädigtes Stromkabel darf nur
vom Hersteller, von einer von ihm aner-
kannten Reparaturwerkstatt oder von
autorisiertem Fachpersonal mit entspre-
chender Qualifikation ausgetauscht
werden, um Gefahren zu vermeiden.
Servicearbeiten dürfen nur von geschul-
tem Fachpersonal ausgeführt werden.
TM03 1112 1005
Servicesatz
Produkt-
nummer
50 Hz
Teile-
nummer
60 Hz
Laufrad, CC5 96578967 97512794
Laufrad, CC7 96578968 97512822
Laufrad, CC9 96578969 97512824
Rückschlagventil 96578978
Adapter für den
Druckstutzen
96578979
Zulaufsieb 96578990
Das Kabel und der Schwimmerschalter
dürfen nur durch eine von Grundfos aner-
kannte Servicewerkstatt ausgetauscht
werden.

Chat with your Grundfos Unilift CC manual using AI

Get instant AI answers from your Grundfos Unilift CC manual

Ask anything about the Grundfos Unilift CC. Answers come from this manual, with the pages they are based on.

Unilift CC Maintenance Schedule

After use with non-clean water
Rinse pump with clean water

If the pump is used to convey media other than clean water, rinse it immediately after use with clean water.

Regularly during manual operation
Check water level

During hand operation, regularly check the water level to prevent the pump from running dry.

M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend Unilift CC?

Yes No

Frequently Asked Questions

A

No, you should not use the pump in swimming pools, garden ponds, or similar places if people are in the water. Additionally, it is not designed for flammable liquids or aggressive chemicals.

Is this answer helpful?

A

For the Unilift CC 7 with a 10-meter cable, the maximum installation depth is 7 meters. Ensure there is at least 3 meters of free cable above the liquid level.

Is this answer helpful?

A

Switch off the power supply first. Loosen the inlet strainer by inserting a screwdriver between the pump sleeve and the strainer, then turn it. Clean the strainer and refit it securely.

Is this answer helpful?

A

Yes, the pump can pump down to 3 mm, but only if the inlet strainer is removed. The pump must be placed on an even surface, and the water level must be at least 5 mm at startup.

Is this answer helpful?

A

The built-in thermal switch will cut out to protect the motor. Once the motor cools to normal temperature, the pump will restart automatically.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Self-venting design eliminates airlocks for reliable priming
  • Thermal protection prevents motor damage from overheating
  • Versatile installation allows vertical, tilted, or horizontal mounting
  • Compatible with float switches for fully automatic operation
  • Durable construction suitable for rainwater and grey wastewater
VS

Disadvantages

  • Unilift CC 5 model restricted to indoor use only
  • Not suitable for liquids containing long fibers or aggressive chemicals
  • Inlet strainer must be removed for pumping to extremely low water levels
  • Requires careful electrical grounding and RCD protection for safety
  • Float switch cable length must be precisely adjusted for correct cycling
M: QW-35-FL

Product Specification

Features

no tank

M: QW-35-FL

Product Description

Grundfos Unilift CC Electric Sewage Submersible Pump Manual

The Grundfos Unilift CC series, including models CC 5, CC 7, and CC 9, represents a robust solution for managing rainwater and grey wastewater in residential and commercial settings. These single-stage submersible pumps are engineered for both stationary and portable applications, making them versatile tools for draining basements, cellars prone to flooding, drainage wells, and tanks connected to roof gutters or tunnels. Designed specifically for liquids without long fibers, these pumps efficiently handle water from washing machines, baths, sinks, and similar sources.

A key feature of the Unilift CC series is its self-venting capability, which includes a built-in vent valve located in the lifting handle. This design ensures that air trapped within the pump or outlet pipe can escape automatically, facilitating quick priming and efficient operation even when the system is not fully flooded initially. The pumps offer flexible installation options, supporting vertical, tilted, or horizontal positioning as long as the outlet port remains the highest point. For installations requiring automation, the units can be equipped with a float switch for automatic start and stop functions based on water levels. Alternatively, they support manual operation via an external switch.

Safety is paramount in the design of these pumps. They incorporate thermal protection that cuts off power if the motor overheats due to dry running or overload, automatically restarting once the motor cools down. The Unilift CC 5 is intended for indoor use only, while the CC 7 and CC 9 models are suitable for both indoor and outdoor environments. When installed correctly, these pumps can operate at depths up to 7 meters depending on the cable length and frequency configuration. Proper maintenance involves regular cleaning of the inlet strainer and impeller to prevent blockages from debris, ensuring long-term reliability and performance.

M: QW-35-FL

© Copyright 2026 Manual.ly