Manual.ly Logo

Grundfos Unilift CC Manual

0.0 · 0 Ratings

PDF manual · 16 Pages

English

M: QW-35-FL
page

/ 16

Loading...
733266de7612ef8b7928dfb7fdac237cad54 page 7
Deutsch (DE)
7
3.1 Entlüften des Produkts
Die Pumpe ist eigenbelüftet. Im Handgriff ist ein Ent-
lüftungsventil eingebaut. Über das Ventil kann Luft
auch dann aus der Pumpe entweichen, wenn der
freie Luftstrom durch die Druckleitung blockiert ist.
Sobald die Pumpe entlüftet ist, schließt sich im Nor-
malfall das Ventil.
Wenn die Pumpe Luft oder Wasser mit einem hohen
Luftanteil ansaugt, kann aus dem Ventil ein Luft-
Wasser-Gemisch austreten. Dies ist keine Störung,
sondern eine normale Folge der Ventilfunktion.
Abb. 12 Entlüftungsventil
3.2 Handbetrieb
Schalten Sie die Pumpe über einen externen Schal-
ter ein und aus.
Um zu verhindern, dass die Pumpe trockenläuft,
muss der Wasserstand regelmäßig während des
Betriebs kontrolliert werden. Der Wasserstand kann
beispielsweise durch ein externes Überwachungsys-
tem kontrolliert werden.
Damit die Pumpe beim Einschalten selbstansaugen
kann, ist ein Wasserstand von mindestens 25 mm
erforderlich.
Wenn die Pumpe Wasser fördert, kann sie bis zu
einem Wasserstand von 20 mm ansaugen.
3.3 Automatischer Betrieb mit
Schwimmerschalter
Im Automatikbetrieb schaltet sich die Pumpe mit
Schwimmerschalter je nach Wasserstand und Posi-
tion bzw. Kabellänge des Schwimmerschalters ein
und aus.
3.3.1 Erzwungener Betrieb der Pumpe mit
Schwimmerschalter
Wenn die Pumpe zum Ablassen von Wasser bis
unterhalb des Ausschaltniveaus des Schwimmer-
schalters verwendet werden soll, kann der Schwim-
merschalter in einer höheren Position fixiert werden,
indem er an die Druckleitung montiert wird.
Während des erzwungenen Betriebs muss der Was-
serstand regelmäßig überprüft werden, um ein Tro-
ckenlaufen zu verhindern.
3.4 Abpumpen bis auf niedrigen
Wasserstand
Wenn das Zulaufsieb demontiert wurde, kann die
Pumpe bis auf 3 mm ansaugen.
Diese Bedingungen müssen erfüllt sein:
• Das Zulaufsieb muss entfernt werden.
• Die Pumpe muss auf einer ebenen, waagerech-
ten Oberfläche aufgestellt werden.
• Das Wasser darf keine Partikel enthalten, die den
Pumpenzulauf blockieren könnten.
• Beim Einschalten der Pumpe ist ein Mindest-
Wasserstand von 5 mm erforderlich.
Abb. 13 Niedriger Wasserstand
Entfernen des Zulaufsiebs
Schieben Sie einen Schraubendreher zwischen das
Pumpengehäuse und das Zulaufsieb und drehen Sie
ihn, um das Zulaufsieb zu entfernen.
Abb. 14 Entfernen des Zulaufsiebs
3.5 Übertemperaturschutz
Sollte die Pumpe trockenlaufen oder auf andere
Weise überlastet sein, schaltet der eingebaute Ther-
moschalter die Pumpe ab.
Nach dem Abkühlen auf die Normaltemperatur
schaltet sich der Motor automatisch wieder ein.
TM03 1121 1105
TM03 0832 0505TM03 0831 0505

Chat with your Grundfos Unilift CC manual using AI

Get instant AI answers from your Grundfos Unilift CC manual

Ask anything about the Grundfos Unilift CC. Answers come from this manual, with the pages they are based on.

Unilift CC Maintenance Schedule

After use with non-clean water
Rinse pump with clean water

If the pump is used to convey media other than clean water, rinse it immediately after use with clean water.

Regularly during manual operation
Check water level

During hand operation, regularly check the water level to prevent the pump from running dry.

M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend Unilift CC?

Yes No

Frequently Asked Questions

A

No, you should not use the pump in swimming pools, garden ponds, or similar places if people are in the water. Additionally, it is not designed for flammable liquids or aggressive chemicals.

Is this answer helpful?

A

For the Unilift CC 7 with a 10-meter cable, the maximum installation depth is 7 meters. Ensure there is at least 3 meters of free cable above the liquid level.

Is this answer helpful?

A

Switch off the power supply first. Loosen the inlet strainer by inserting a screwdriver between the pump sleeve and the strainer, then turn it. Clean the strainer and refit it securely.

Is this answer helpful?

A

Yes, the pump can pump down to 3 mm, but only if the inlet strainer is removed. The pump must be placed on an even surface, and the water level must be at least 5 mm at startup.

Is this answer helpful?

A

The built-in thermal switch will cut out to protect the motor. Once the motor cools to normal temperature, the pump will restart automatically.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Self-venting design eliminates airlocks for reliable priming
  • Thermal protection prevents motor damage from overheating
  • Versatile installation allows vertical, tilted, or horizontal mounting
  • Compatible with float switches for fully automatic operation
  • Durable construction suitable for rainwater and grey wastewater
VS

Disadvantages

  • Unilift CC 5 model restricted to indoor use only
  • Not suitable for liquids containing long fibers or aggressive chemicals
  • Inlet strainer must be removed for pumping to extremely low water levels
  • Requires careful electrical grounding and RCD protection for safety
  • Float switch cable length must be precisely adjusted for correct cycling
M: QW-35-FL

Product Specification

Features

no tank

M: QW-35-FL

Product Description

Grundfos Unilift CC Electric Sewage Submersible Pump Manual

The Grundfos Unilift CC series, including models CC 5, CC 7, and CC 9, represents a robust solution for managing rainwater and grey wastewater in residential and commercial settings. These single-stage submersible pumps are engineered for both stationary and portable applications, making them versatile tools for draining basements, cellars prone to flooding, drainage wells, and tanks connected to roof gutters or tunnels. Designed specifically for liquids without long fibers, these pumps efficiently handle water from washing machines, baths, sinks, and similar sources.

A key feature of the Unilift CC series is its self-venting capability, which includes a built-in vent valve located in the lifting handle. This design ensures that air trapped within the pump or outlet pipe can escape automatically, facilitating quick priming and efficient operation even when the system is not fully flooded initially. The pumps offer flexible installation options, supporting vertical, tilted, or horizontal positioning as long as the outlet port remains the highest point. For installations requiring automation, the units can be equipped with a float switch for automatic start and stop functions based on water levels. Alternatively, they support manual operation via an external switch.

Safety is paramount in the design of these pumps. They incorporate thermal protection that cuts off power if the motor overheats due to dry running or overload, automatically restarting once the motor cools down. The Unilift CC 5 is intended for indoor use only, while the CC 7 and CC 9 models are suitable for both indoor and outdoor environments. When installed correctly, these pumps can operate at depths up to 7 meters depending on the cable length and frequency configuration. Proper maintenance involves regular cleaning of the inlet strainer and impeller to prevent blockages from debris, ensuring long-term reliability and performance.

M: QW-35-FL

© Copyright 2026 Manual.ly