Manual.ly Logo

Gloria FoamMaster Manual

0.0 · 0 Ratings

PDF manual · 24 Pages

English

M: QW-35-FL
page

/ 24

Loading...
fa7d5b02ff428a321c7fa1f0b1cf00209c47 page 8
l Durch Betätigen der Auslösetaste (A)am Ven-
tilkörper wird der Sprühvorgang ausgelöst. Das
Loslassen der Auslösetaste (A)bewirkt eine so-
fortige Unterbrechung des Sprühvorgangs.
l Wenn der Behälterdruck auf etwa 1,0 bar
abgesunken ist, Druck nachpumpen, um gleich-
mäßige Flüssigkeitsverteilung zu
gewährleisten.
Besprühen von Bodenflächen
l Knicken Sie das Spritzrohr (F)am Gelenkstück
(E)nach unten, so dass die Düse auf den Boden
gerichtet ist und Sie das Gerät senkrecht halten
können.
l Betätigen Sie die Auslösetaste (A)und sprü-
hen Sie den Schaum gleichmäßig auf die zu
reinigende Fläche.
Einstellung der Schaumstabilität
Sie haben die Möglichkeit durch Austauschen der
Schaumpatrone (G)die Stabilität des Schaumes
zu verändern. Werkseitig ist die blaue Schaum-
patrone montiert, diese ist besonders geeignet für
den GLORIA Stein Grundreiniger, den GLORIA Grün-
belag Entferner sowie den GLORIA Holz / WPC Rei-
niger. Für festeren Schaum ersetzen Sie die blaue
Schaumpatrone durch die, rote oder schwarze
Schaumpatrone. In dieser Reihenfolge wird der
Schaum immer stabiler.
Entleerung und Wartung
l Durch Anheben des Knopfes am Sicherheits- /
Druckentlastungsventil(C)wird der eventuelle
Restdruck im Behälter (L)abgeblasen.
l Der Ventilkörper (D)wird vorsichtig, zunächst
nur einige Gewindegänge durch Linksdrehung
losgeschraubt, damit evtl. im Behälter ver-
bliebene Druckluft entweichen kann. Erst dann
den Ventilkörper ganz herausschrauben und
aus dem Behälter nehmen.
l Gerät nach Gebrauch entleeren und durch-
spülen.
Hinweis!Über die Einfüllöffnung kann ein
Flüssigkeitsrest im Behälter restlos ausge-
schüttet werden (bei wassergefährdenden
Flüssigkeiten, siehe Kapitel “Wichtige Si-
cherheitshinweise, sowie Vorgaben des
Mittelherstellers). Wahl und Entsorgung
der Spülflüssigkeit richten sich nach den
Vorgaben des Mittelherstellers. Auch beim
Spülen die Beständigkeit der Gerätewerk-
stoffe beachten.
l Spülen Sie nach dem Gebrauch des Gerätes
immer zusätzlich die Schaumpatrone (G) mit
Wasser aus. Hierzu lösen Sie die Überwurfmutter
(K)mit der Düse (J) und der Dichtung (I) von
dem Gerät. Entnehmen Sie nun die Schaum-
patrone (G) und reinigen Sie diese.
l Die Lebensdauer der Pumpe wird erheblich ver-
längert wenn ab und zu der Pumpen-O-Ring
mit harz- und säurefreiem Fett geschmiert wird.
l Sollte die Schaumbildung nicht mehr gegeben
sein, prüfen Sie ob die Lufteinlassbohrungen
im Anschlussnippel(H)verstopft sind, ggf. diese
säubern.
Hinweis!Starke Beanspruchung aufgrund
der Betriebsweise (einschl. des Transports
zum Einsatzort und der Aufbewahrung bei
Nichtbenutzung), Umgebungseinflüsse
(des Einsatzortes und des Aufbewah-
rungsortes bei Nichtbenutzung), mangel-
hafte Wartung und Pflege können zu vor-
zeitigem Verschleiß des Gerätes führen. Es
sollte daher vor jeder Benutzung auf si-
cheren und betriebsfähigen Zustand, zu-
mindest jedoch auf äußerlich erkennbare
Schäden, geprüft werden. Insbesondere
bei Auftreten sicherheitsbedenklicher Män-
gel, jedoch mindestens alle 2 Jahre haben
Sachkundige, am besten der Wartungs-
dienst des Herstellers, zu prüfen, ob ein ge-
fahrloser Betrieb weiterhin möglich ist.
DE IT
E
8
FM10_flex.qxp_Innenseiten_FM10 flex.qxd 08.02.18 16:29 Seite 8

Chat with your Gloria FoamMaster manual using AI

Get instant AI answers from your Gloria FoamMaster manual

Ask anything about the Gloria FoamMaster. Answers come from this manual, with the pages they are based on.

FoamMaster Maintenance Schedule

Remind me when maintenance is due
Every 2 years
Professional inspection

Have a specialist or manufacturer service station check the sprayer for safe operation, especially if safety defects appear.

After every use
Empty and rinse

Empty the tank completely and rinse the unit thoroughly after each use to prevent corrosion and residue buildup.

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: QW-35-FL

Ask a Question

0/1000

Do you recommend FoamMaster?

Yes No

Frequently Asked Questions

A

The maximum filling volume is 5.0 liters. However, the total capacity of the device is approximately 12.2 liters. Do not exceed the 5.0-liter limit to prevent pressure issues.

Is this answer helpful?

A

No, the Gloria FoamMaster FM50 is strictly prohibited from being used with flammable liquids, oils, fuels, or media that could cause cracks in the plastic components. Using it for these substances poses a severe fire and explosion risk.

Is this answer helpful?

A

It is recommended to have the pressure sprayer undergo a thorough inspection every two years. For safety reasons, it should also be checked before each use for visible damage or leaks.

Is this answer helpful?

A

The device is equipped with a safety pressure relief valve. If the pressure reaches the maximum limit of 3 bar, the valve will activate to vent any excess pressure, preventing damage to the unit.

Is this answer helpful?

A

You can adjust the degree of foaming by turning the handwheel on the pressure reducing valve (C). Turning clockwise increases pressure and foam, while turning counter-clockwise decreases them.

Is this answer helpful?

A

No, the unit should not be left under pressure for extended periods. You must empty and rinse the sprayer after every use to ensure safety and prevent material fatigue.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Durable construction with polyethylene tank and polypropylene pump resistant to chemicals
  • Adjustable pressure reducer allows precise control over foam density and spray pressure
  • High delivery rate of 290ml/min ensures efficient coverage during cleaning tasks
  • Integrated compressor connection (D) offers versatile power options for rapid repressurization
  • Safety relief valve prevents dangerous overpressure situations by venting excess air at 3 bar
VS

Disadvantages

  • Not suitable for use with flammable liquids, oils, fuels, or aggressive acids like formic acid
  • Requires regular manual inspection every two years to maintain safety compliance and warranty
  • Cannot be used for storing liquids; must be emptied and rinsed thoroughly after every single use
  • Pump assembly requires specific 180-degree rotation steps for removal which may confuse new users
  • Maximum operating temperature limit of +40°C restricts usage in hot environments or direct sunlight
M: QW-35-FL

Product Description

Gloria FoamMaster Pressure Sprayer Manual: A Comprehensive Guide to Professional Cleaning

The Gloria FoamMaster FM50 is a robust industrial pressure sprayer designed specifically for the efficient foaming of liquid cleaning agents. Whether you are managing large-scale facility maintenance or handling demanding professional cleaning tasks, this manual provides the essential knowledge to operate the device safely and effectively. The unit features a high-capacity 5-liter filling volume within a total capacity of approximately 12.2 liters, making it ideal for extended use without frequent refills.

Constructed with durable materials, the tank is made of polyethylene while the pump utilizes polypropylene, ensuring resistance against corrosion and chemical degradation. The device operates at a maximum overpressure of 3 bar and can withstand temperatures up to +40°C. Its flat spray nozzle delivers a precise 110-degree pattern, allowing for controlled application of cleaning solutions. The inclusion of an adjustable pressure reducer with a manometer gives users full control over the spraying process and foam density.

Safety is paramount in the design of the Gloria FoamMaster. The manual emphasizes strict adherence to safety protocols, including the use of personal protective equipment when handling hazardous substances. It explicitly warns against using the sprayer for flammable liquids, acids, or oils that could damage the internal components. Regular maintenance, such as checking the safety relief valve and lubricating the pump O-ring, is crucial for longevity. By following the detailed instructions found in this guide, operators can ensure a safe working environment and maximize the performance of their cleaning operations.

M: QW-35-FL

© Copyright 2026 Manual.ly