Manual.ly Logo

Ersa Independent 75 Manual

5.0 · 1 Ratings

PDF manual · 2 Pages

English

M: OA-GPT-5-NAN
page

/ 2

Loading...
2162dad06a2275c894b7926142d971f36296 page 2
D
Vor Inbetriebnahme des Gaslöt-
kolbens ist zu beachten:
Before taking the tool into use
make sure of the following:
Avant la mise en service il est
nécessaire d’observer les aspects
suivants:
Bitte lesen Sie diese Betriebsanleitung und die Sicher-
heitshinweise vor der ersten Inbetriebnahme vollständig
durch.
• Der Gaslötkolben ist werkseitig aus Sicherheitsgründen
nichtbefüllt.
• Der Ersa Gaslötkolben INDEPENDENT 75 enthält
brennbares Butangas, das unter Druck steht. Bitte achten
SiedaheraufsorgfältigeHandhabung.
• DieUmgebungstemperaturfürdenErsaINDEPENDENT75
darfnichthöherals+50°C(120°F)sein.
• DenGaslötkolbenstetsvonKörperundGesichtweghalten.
• Nichtinder Nähe brennbarer Substanzenanzünden oder
benutzen!
• VergewissernSiesichvordemAblegendesKolbens,daß
dieFlammenvollständigerloschensind.WenndieFlamme
nachdemEntzündennichtinnerhalbvon30serlischt,muß
die Spitze ausgewechselt werden.
• Vor dem Aufstecken der Verschlußkappe und dem
Nachfüllendaraufachten,daßderErsaINDEPENDENT75
ausgeschaltetunddieSpitzeabgekühltist.
• Aus Sicherheitsgründen den Ersa INDEPENDENT 75
keinesfalls verändern (nicht gewaltsam öffnen, anbohren
oder verbrennen). Notwendige Reparaturen werden im
Werkausgeführt.
• NuraußerhalbderReichweitevonKindernaufbewahren.
Please read through these operating instructions and the
safety instructions completely before commissioning.
• Thegassolderingironisnotpre-filledforsecurityreasons.
• ThegassolderingironErsaINDEPENDENT75incorporates
a combustible gas which is under pressure. Therefore
please observe carefully the directions for use.
• Theambient temperaturefor theErsaINDEPENDENT75
must not exceed + 50° C (120° F).
• Itisessentialtoignitethetoolwiththetippointingawayfrom
face and body.
• Donotuseorignitenearcombustiblesubstances.
• Donotlay down before theflamehas extinguished. If the
flame does not extinguish within 30 seconds of ignition the
tip must be renewed.
• Makesurethatthegassolderingironisswitchedoffandthe
tip has cooled down before refilling and fitting the closure
cap.
• NevermakeanychangestotheErsaINDEPENDENT75for
safety reasons (do not force open, drill or burn).
• Keepoutofreachofchildren.
Veuillez lire entièrement ce mode l’emploi et l’instructions
de sécurité!
• Pour des motifs de sécurité, le soudeur à gaz n‘est pas
rempli par le fabricant.
• LeferàsouderàgazINDEPENDENT75deErsarenferme
du gaz combustible sous pression. Pour cette raison
manipuler le fer à souder à gaz avec précaution.
• Nepas exposer le fer à souder à gazà une température
supérieure à 50° C (ce qui correspond à 120° F).
• Nejamaisdirigerlapanneduferàsouderaugazversle
visage et le corps.
• Nepasutiliseràproximitédematériauxcombustibles.
• S’assurerquel’outilesttotalementéteintavantdelelaisser
hors de surveillance. Lorsque la flamme ne s’éteint pas dans
les 30 secondes qui suivent l’allumage, il est indispensable
de remplacer la panne.
• Aprèsavoireffectuéleremplissageetavoiremmanchéle
capuchon d’obturation, veillez à ce que le fer à souder à gaz
soit coupé et que la panne soit refroidie.
• Pour des raisons de sécurité, n’entreprendre aucune
modification du fer (ne pas l’ouvrir de force, ne pas percer
detrou,nepaslebrûler).Lorsquedesréparationss’avèrent
nécessaires, elles seront effectuées en usine.
• Tenirleferàsouderàgazhorsdelaportéedesenfants.
Verwendbares Gas
Ihr Gaslötkolben Ersa INDEPENDENT 75 arbeitet mit
normalem Feuerzeug-Butangas. Verwenden Sie nur gefiltertes
Gas, d.h. bekannte Marken, wie z.B. Ronson, Braun oder
Colibri.Etwas flüssiges Gas sollte im Sichtfenster zusehen
sein.Gasdampfallein ist für dieFunktiondes Gerätes nicht
ausreichend.
Gas type
The Ersa INDEPENDENT 75 operates on butane gas such
as used with ordinary cigarette lighters. Use only filtered gas
such as the Ronson, Braun, or Colibri, brands. A small amount
of liquid gas should be visible through the Gas Inspection
Window; gas vapour alone will not generate sufficient pressure.
Gaz
Cet fer à souder à gaz Ersa INDEPENDENT 75 utilise du gaz
butane identique à celui destiné au briquet. N’utiliser que du
gaz filtré de qualité, comme Ronson, Braun, ou Colibri. Le
niveau de gaz doit être visible dans le récipient pour assurer
un remplissage suffisant.
Entzündungsvorgang (Abb. 1)
Der Ersa INDEPENDENT 75 wird durch ein piezo-elektronisches
System gezündet. Der Gas-EIN/AUS-Schalter ist als “GAS”
gekennzeichnet. Der Zündschalter ist mit einem “Blitz-
Symbol” markiert.
Achtung! Nach Gebrauch können Spitze und Überwurf-
mutter noch heiß sein. Vor Berührung mit der Hand bitte
abkühlen lassen!
Löt- Gebläse- und Schneidfunktion
Die gewählte Spitze einsetzen und mit der Überwurfmutter
befestigen. Temperaturregler auf “max.” stellen. Durch Vor-
schiebendesGas-EIN/AUS-Schalters die Gaszufuhr öffnen.
Den Zündschalter zurückschieben und anschließend loslas-
sen. Die erfolgreiche Zündung wird durch das Glühen des
Katalysators in der Spitze angezeigt.
Brennerfunktion
Zum Zünden der Flamme Temperaturregler auf “Mittelwert”
einstellen.
Achtung!DieFlammekannbeientsprechendenLichtverhält-
nissen unsichtbar sein.
Temperatureinstellung
Durch Drehen des Temperaturreglers kann die Temperatur
der Spitze stufenlos eingestellt werden. Zur Orientierung ist
dasGehäusemit +/- gekennzeichnet. Die ideale Einstellung
ermitteln Sie durch Versuche an einem Werkstück (Objekt),
da sowohl Lötstelle als auch Bauteile sehr unterschiedlich
beschaffenseinkönnenunddadurchunterschiedlicheAnfor-
derungen stellen. Um die richtige Temperatur zu erhalten, ist
esnichterforderlich,daßderKatalysatorhellrotglüht.
Ignition Sequence (fig. 1)
The Ersa INDEPENDENT 75 is ignited by a piezo-electronic
system. The Gas ON/OFF switch is marked “GAS”. The igni-
tion switch is marked with a “lightning strike” logo.
Caution: After use the tip and retaining collar may still be
hot. Allow to cool sufficiently before touching.
Soldering, Hot air, and hot knife tips
Fit tip of choice and retaining collar. Turn temperature regu-
lator button to max. setting. Turn gas on by pushing forward
Gas ON/OFF Switch. Click back ignition switch, and allow the
switch to return. Glowing catalyst in the tip exhaust ports will
confirm operation.
Flame tips
For activating the flame, adjust Temperature Regulator to
middle value.
N.B. Flame is difficult to see in certain lighting situations.
Temperature adjustment
The tip temperature can be set as required by turning the
Temperature Regulator. The housing is marked with +/- for
orientation purposes. You can determine the ideal setting by
trial soldering on a work piece (i.e. object), since both the
soldering joint as well as the components have varying proper-
ties, and, as a consequence, demand different treatment. It is
not necessary for the tip to glow bright red to achieve satisfac-
tory soldering temperatures.
Allumage (fig. 1)
L’INDEPENDENT75s’allumegrâceàunsystèmepiezoélec-
trique. La commande d’ouverture du gaz est le bouton marqué
‘’GAS’’. La commande d’allumage piezo électrique est le bou-
ton marqué d’un éclair.
Attention: Après usage la panne et la bague de rete-
nue peuvent être chaudes. Attendre quelques instants
qu’elles refroidissent avant de les manipuler.
Soudage, air chaud et panne couteau
Fixer le panne adéquate à l’aide de la bague de retenue
sur l’extrémité du Ersa INDEPENDENT 75. Tourner le
régulateur de température sur la position maximum (HI).
Ouvrir le débit du gaz en poussant l’interrupteur dans le
sens de triangle. Actionner l’interrupteur piezo vers le bas
jusqu‘au déclic et laissez-le revenir librement dans sa
position initiale. Le rougeoiement, aisément visible à travers
l’orifice d’échappement des gaz de la panne confirme le bon
fonctionnement du catalyseur.
Embout chalumeau
Régler le débit de gaz sur moyen ou faible. Allumer suivant la
procédure décrite plus haut. La flamme peut d’éteindre d’elle-
même si le débit de gaz est trop important.
Attention, la flamme n’est pas toujours visible dans certaines
conditions d’éclairage.
Réglage de température
Il est possible, en tournant la soupape de régulateur de tempé-
rature, de régler en continu la température de la panne. A titre
d’information,lecarterportelesrepèresd’identification+/-.Le
réglage idéal doit être déterminé en faisant des essais sur une
pièce à usiner (objet), étant donné que la connexion et les
composantspeuventprésenteruneconstitutiontrèsdifférente
et,decefait,imposerdesexigencestrèsvariées.Iln’estpas
nécessaire d‘utiliser la température maximum pour réaliser
des bonnes soudures.
Gas Nachfüllen (Abb. 4)
Den Gas-EIN/AUS-Schalter in „AUS“-Position bringen. Für
das Nachfüllen halten Sie Ihren Ersa INDEPENDENT 75
mit der Spitze nach unten und pressen Sie die Düse der
Gaskartusche in das Nachfüllventil des Gaslötkolbens.
Schwerkraftund Druckin derNachfüllpatrone bewirkendas
Füllen.DiemaximaleGasfüllungisterreicht,wennausdem
Füllventil Gas hörbar entweicht. Das eingebaute Spezial-
EntlüftungsventilerlaubteinfachesundschnellesNachfüllen.
Gas filling (fig. 4)
Gas ON/OFF Switch must be in the OFF position before filling.
For refilling your INDEPENDENT 75 is to be held with the tip
facing downwards. Then press the nozzle of the gas cartridge
in the refilling valve of the gas soldering iron. Keep can and
tool in truly vertical position during refill. Gas has been refilled
to a maximum as soon as the gas overflows from the valve.
The special venting valve allows quick and easy charging.
Remplissage de gaz (fig. 4)
Le interrupteur doit être coupé avant tout remplissage. Pour
effectuerleremplissage,tenirl’INDEPENDENT75demanière
à ce que la panne soit dirigée vers le bas, puis presser la buse
de la cartouche à gaz dans la soupape de remplissage du fer
á souder à gaz. Tenir le fer à souder et le recharger de gaz en
position verticale. Lé réservoir est plein lorsque le gaz reflue
parlavalve.Lesystèmeparticulierd’aérateurmaximumdela
valvepermetleremplissagetrèsrapide.
Spitzenwechsel (Abb. 3)
Allezur VerfügungstehendenSpitzen(siehe Fig. 3)können
mit Hilfe der Überwurfmutter leicht montiert, abgenommen
oder ausgewechselt werden.
Achtung! Aus der Gas-Austrittsöffnung tritt Heißgas
von 580° C aus. Das Gerät nie unbeaufsichtigt lassen.
Beim Ablegen auf einer Unterlage immer darauf achten,
daß die Gas-Austrittsöffnung nach oben zeigt und der
Kolbenkörper auf der Verschlußkappe liegt (siehe Abb. 5).
Temperaturbereiche
Lötspitzen: max.580°C(1.075°F)
Flamme: max. 1.300° C (2.372° F)
Heißgasdüse:max.625°C(1.150°F)
Glühmesser: max.580°C(1.075°F)
Tip replacement (fig. 3)
Soldering, hot air, and other tips are easily removed or
installed, by unscrewing the retaining collar and sliding the tip,
collar, and nut over the ignition assembly. Remove the tip, and
replace with new or alternate unit. Slide back into place and
screw into position. See fig.3 for alternatives.
Caution! Hot gases of 580° C+ are emitted from the tip
exhaust ports. Do not leave the INDEPENDENT 75 unat-
tended. If placing on surface, leave ports facing upwards
and rest iron on the cap as per Fig. 5.
Tip temperature ranges
Soldering tips Up to 580°C (1075° F.)
Flame nozzle Up to 1300°C (2372° F.)
Hot gas nozzle Up to 625°C (1150° F.)
Hot blade Up to 580°C (1075° F.)
Remplacement des pannes (fig. 3)
Les différentes pannes ou buses peuvent être facilement
installées ou retirées. Dévisser la bague de retenue, et
retirez-là de l’ensemble d’allumage. Retirer la panne, placer
la nouvelle panne ou buse et replacer la bague de retenue en
effectuant l’opération inverse (voir fig. 3).
Attention: Les ouvertures d’échappement émettent du
gaz de plus de 580° C. Ne pas laisser l’apparat hors de
surveillance. S’assurer que les ouvertures faisant face vers
le haut et laisser les corps du fer sur le couvercle. Voir g. 5.
Température de chauffe
Panne à souder: 580°C (1,075°F) maximum
Buse torche: 1,300°C (2,372°F) maximum
Buse à gaz chaud: 625°C (1,150°F) maximum
Couteau incandescent: 580°C (1,075°F) maximum
Änderungenvorbehalten•Subjecttoalteration•Modificationstechniquesréservées•Wijzigingenvoorbehouden•Modichesonopossibilisenzaalgunpreaviso•Sujetoacambiossinautorización•3BA00064-00•02/2014©byErsa
Temperaturregler
Temperature Regulator
Régulateur de température
Gassichtfenster
Gas Inspection Window
Niveau de gaz
Zündschalter
Ignition Switch
Bouton d’allumage
Gas EIN-AUS-Schalter
Gas ON-OFF switch
Interrupteur
Abb. 1/
Fig. 1
Lötspitze
Soldering tip
Panne à souder
Spitzenhalterung
Tip Retention Tube
Tube de Maintien
Kolbenkörper
Iron Body
Corps du fer
Katalysator
Catalyst
Catalyseur
Befestigungs-Überwurfmutter
Retaining Nut / Bague
Abb. 2/
Fig. 2
0G072CN 0G072KN 0G072AN 0G072VN 0G072BE 0G072MN 0G072FE 0G072RE
Abb. 3 / fig. 3
Abb. 4/
Fig. 4
Abb. 5/
Fig. 5
Ersatzteile / Bestelldaten
G070KN GaslötkolbenINDEPENDENT75
mitLötspitzeG072KN
G072CN Lötspitze(1,0mmmeißelförmig)
G072KN Lötspitze(2,4mmmeißelförmig)
G072AN Lötspitze(3,2mmmeißelförmig)
G072VN Lötspitze(4,8mmmeißelförmig)
G072BE Flammdüse
G072MN Glühmesser
G072HE Heißgasdüse
G072RE Reektor-Aufsatz
A20 Ablagebügel
006 Reinigungsschwamm
G156 Schwammbehälter
KF006 Kunststoffetui
Replacement parts
G070KN Gas soldering iron INDEPENDENT 75
with soldering tip G072KN
G072CN Soldering tip (1.0 mm chisel-shaped)
G072KN Soldering tip (2.4 mm chisel-shaped)
G072AN Soldering tip (3.2 mm chisel-shaped)
G072VN Soldering tip (4.8 mm chisel-shaped)
G072BE Flame nozzle
G072MN Hot blade
G072HE Hot gas nozzle
G072RE Deector
A20 Holder
006 Cleaning sponge
G156 Box for sponge
KF006 Plastic case
Pièces de rechange
G070KN Fer à souder à gaz INDEPENDENT 75
avec panne à souder G072KN
G072CN Panne à souder (1,0 mm tournevis)
G072KN Panne à souder (2,4 mm tournevis)
G072AN Panne à souder (3,2 mm tournevis)
G072VN Panne à souder (4,8 mm tournevis)
G072BE Buse torche
G072MN Couteau incandescent
G072HE Buse à gaz chaud
G072RE Miserapportéerééchissant
A20 Repose-fer
006 Eponge en viscose
G156 Porte-éponge pour éponge en viscose
KF006 Etui en mat. synthétique
Betriebsanleitung/Operating instructions/Mode d’emploi/
Gebruiksaanwijzing/Istruzioni per l’uso/Instrucciones de servicio
Gaslötkolben/Gas soldering iron/
Fer à souder à gaz/Gassoldeerbout/
Saldatore a gas/Soldador de gas
Ersa INDEPENDENT 75

Chat with your Ersa Independent 75 manual using AI

Get instant AI answers from your Ersa Independent 75 manual

Ask anything about the Ersa Independent 75. Answers come from this manual, with the pages they are based on.

Independent 75 Maintenance Schedule

When flame fails to extinguish
Replace tip if flame does not go out

If the flame does not extinguish within 30 seconds of ignition, replace the tip immediately.

Before refilling
Ensure tip is cooled before handling

Allow the tip and retaining collar to cool down completely before touching or refilling the gas.

M: QW-35-FL

Ask a Question

0/1000

Do you recommend Independent 75?

Yes No
0
User Pic

maria_k

9 months ago

Is the soldering iron easy to use right away, or do I need to read the manual to get it working?

0
User Pic

Manual.ly

9 months ago

Yes. Based on user feedback, the device is ready to use quickly after unpacking and filling gas. After unlocking it and pressing the Piezo switch once, the soldering iron can be used immediately. Users also report it is intuitive to operate without having to read the instructions first. If you want the best results, still follow the basic start-up steps (unlocking, gas fill, and initial ignition) and observe the recommended warm-up and safe handling guidance.

M: OA-GPT-5-NAN
M: OA-GPT-5-NAN

Frequently Asked Questions

A

The Independent 75 uses filtered butane (same type as lighter gas). Use reputable brands such as Ronson, Braun, or Colibri. A small amount of liquid gas should be visible in the inspection window for proper pressure.

Is this answer helpful?

A

Switch the gas to OFF, hold the tool with the tip pointing down, press the cartridge nozzle into the refill valve and keep tool and can vertical. Refill stops when gas overflows from the valve. Use the venting valve for a quick, safe refill.

Is this answer helpful?

A

Available tips include chisel soldering tips (1.0–4.8 mm), flame nozzle, hot-gas nozzle and hot blade. Unscrew the retaining collar, slide out the old tip, insert the new tip and screw the collar back in place.

Is this answer helpful?

A

Soldering tips reach up to 580°C, hot-gas nozzles up to 625°C, and the flame nozzle up to 1300°C. Use the continuous temperature regulator to tune heat to the task; the catalyst need not glow bright red to be effective.

Is this answer helpful?

A

Keep the tool away from face and body, do not use near flammables, ensure the flame is fully out before laying down, allow tips to cool before handling, and store out of children’s reach. Do not open, drill, or modify the unit.

Is this answer helpful?

A

If the flame does not go out within 30 seconds after switching off, the tip must be replaced. Always ensure the device is off and cooled before refilling or fitting the closure cap.

Is this answer helpful?

A

No. For safety reasons do not force open, drill, burn, or modify the unit. Any necessary repairs should be performed by the manufacturer or authorized service centers.

Is this answer helpful?

M: OA-GPT-5-NAN

Advantages and Disadvantages

Advantages

  • Portable gas operation allows use without mains power or cords.
  • Interchangeable tips (soldering, flame, hot-gas, hot blade) for many tasks.
  • Piezo ignition and continuous temperature regulator for easy control.
  • Fast, simple refilling via built-in venting valve and inspection window.
  • High maximum temperatures (up to 1300°C for flame nozzle) for heavy-duty jobs.
VS

Disadvantages

  • Contains pressurized butane—requires careful handling and storage.
  • Exhaust ports emit very hot gases (≈580°C); risk if left unattended.
  • Not prefilled by manufacturer; user must refill safely and correctly.
  • Flame can be hard to see in bright light, complicating visual checks.
  • Repairs must be done by the factory; no user modifications allowed.
M: OA-GPT-5-NAN

Product Specification

Power

75W

Temperature

max. 1076°F

Soldering Tip Width

0.09in

Heat-up Time

46s

Weight

0.66lb

Package Contents

Box, 4x Soldering Tip, 2x Nozzle

M: OA-GPT-54-NAN

Product Description

Ersa Independent 75 Profi Set Gaslötkolben Manual

The Ersa Independent 75 Profi Set is a versatile gas-powered soldering iron designed for professionals and hobbyists who need portable, high-temperature performance without an electrical connection. Compact and robust, the Independent 75 accepts multiple interchangeable tips—soldering chisel tips, flame nozzles, hot-gas nozzles and a hot blade—making it suitable for precision soldering, brazing, heating, shrink tubing, and light cutting tasks. A piezo-electric ignition and an adjustable temperature regulator let you control heat output smoothly for different applications.

As a handheld tool that runs on filtered butane (brands such as Ronson, Braun or Colibri recommended), the unit relies on cartridge pressure and gravity for refilling. The refill procedure requires the gas switch to be OFF, holding the tool tip-down, and pressing the cartridge nozzle into the refill valve until excess gas escapes. An integrated venting valve simplifies and speeds up refills. The transparent gas inspection window lets you confirm a small visible liquid gas level for reliable operation.

Safety and usability are emphasized: follow manufacturer guidance to keep the ambient temperature below 50°C, never point the tip toward face or body, avoid use near flammable materials, and allow tips to cool before handling. If a flame does not extinguish within 30 seconds after ignition, replace the tip. The tool must not be forcibly opened, drilled or modified; repairs should be carried out by the manufacturer. When resting the device, position exhaust ports upward and set the iron body on the closure cap to prevent heat damage.

Temperature ranges are broad: soldering tips reach up to 580°C, the flame nozzle up to 1300°C, and hot-gas nozzles around 625°C—providing the flexibility to tackle delicate electronics soldering as well as more demanding heating tasks. Tips are quickly swapped by unscrewing the retaining collar and sliding the chosen tip into place. The glowing catalyst in the tip exhaust confirms successful ignition and operation.

Compact, reliable and adaptable, the Ersa Independent 75 is a powerful solution when mains power is unavailable or mobility is essential. Its modular tip system and continuous temperature control make it an all-purpose gas soldering tool for fieldwork, repairs, and workshops.

Notes

  • Use only filtered butane from reputable brands and confirm liquid gas visibility in the inspection window.
  • Always refill with the tool OFF and tip pointing downward; stop when gas escapes from the valve.
  • Keep out of reach of children and do not alter the unit; factory servicing only.
M: OA-GPT-5-NAN

© Copyright 2026 Manual.ly