Manual.ly Logo

Eltako SNT61-230V/24VDC-0.25A Manual

0.0 · 0 Ratings

PDF manual · 1 Pages

English

M: claude-opus-5-5
page

/ 1

Loading...
3b1e35b962fbd4df68e28bb8b44b6aa382ed page 1
D
Nennleistung 6W.
Stand-by-Verlust nur 0,1Watt.
Für Einbau- und AP-Montage.
45mm lang, 55mm breit, 33mm tief.
Eingangsspannung 230V (-20% bis
+10 %).
Wirkungsgrad:
SNT61-230V/12V DC-0,5A: 81%.
SNT61-230V/24V DC-0,25A: 82%
Stabilisierte Ausgangsspannung ±1%,
geringe Restwelligkeit.
Kurzschlussfest.
Überlast- und Übertemperatursicherung
durch Abschalten mit automatischem
Zuschalten nach der Fehlerbeseitigung
(Autorecovery-Funktion).
Technische Daten
Restwelligkeit 100mV
Schutzklasse II
Schutzart IP20
Einschaltstrom
1)
18A/230V
Überlastschutz kurzseitig 160-200%
Überspannungsschutz 140-170%
Parallel schaltbar, Anzahl
_
Betriebstemperatur -10/+50°C
1)
Bei primärseitiger Zuschaltung, 2ms.
Schaltnetzteile
SNT61-230V/12V DC-0,5A und
SNT61-230V/24V DC-0,25A
61 000 164 - 1
Diese Geräte dürfen nur durch eine
Elektrofachkraft installiert werden,
andernfalls besteht Brandgefahr oder
Gefahr eines elektrischen Schlages!
Eltako GmbH
D-70736 Fellbach
+49 711 94350000
www.eltako.com
11/2013 Änderungen vorbehalten.
Zum späteren Gebrauch aufbewahren!
GB
Rated capacity 6W.
Standby loss 0.1 watt only.
Built-in device for installation and surface
mounting.
45mm long, 55mm wide, 33mm deep.
Input voltage 230V (-20% up to +10%).
Efficiency:
SNT61-230V/12V DC-0,5A: 81%.
SNT61-230V/24V DC-0,25A: 82%
Stabilised output voltage ±1%,
low residual ripple.
Short-circuit proof.
Overload protection and over-temperature
switch-off by means of swichting off with
automatic switching-on after fault clea-
rance (autorecovery function).
Technical data
Residual ripple 100mV
Class of protection II
Protection degree IP20
Starting current
1)
18A/230V
Overload protection 160-200%
short-term
Overvoltage protection 140-170%
Switchable in parallel, number
_
Operating temperature -10/+50°C
1)
If connected on the primary side, 2ms.
Switching power supply units
SNT61-230V/12V DC-0,5A and
SNT61-230V/24V DC-0,25A
61 000 164 - 1
Only skilled electricians may install
this electrical equipment otherwise
there is the risk of fire or electric
shock!
Eltako GmbH
D-70736 Fellbach
+49 711 94350000
www.eltako.com
11/2013 Subject to change without notice.
Must be kept for later use!
Temperatur an der Einbaustelle:
-10°C bis +50°C.
Lagertemperatur: -25°C bis +70°C.
Relative Luftfeuchte:
Jahresmittelwert <75%.
Temperature at mounting location:
-10°C up to +50°C.
Storage temperature: -25°C up to +70°C.
Relative humidity:
annual average value <75%.
Potencia nominal 6W.
Perdida Stand-by solo 0,1Watt.
Para el montaje en cajas empotradas y
superficie. 45mm de longitud, 55mm
de anchura,
33mm
de profundidad.
Tensión
230V (-20% hasta +10%).
Rendimiento:
SNT61-230V/12V DC-0,5A: 81%.
SNT61-230V/24V DC-0,25A: 82%
Tensión de salida estabilizada ±1%,
ondulación residual minima.
Resistente al cortocircuito.
Protección contra sobretemperatura y
sobrecarga por desconexión, con conexión
automática después de la eliminación
del error (función autorecovery).
Datos técnicos
Ondulación residual 100mV
Clase de protección II
Tipo de protección IP20
Corriente de encender
1)
18A/230V
Protección sobrecarga 160-200%
brevemente
Überspannungsschutz 140-170%
Numero de conexión en
_
paralelo
Temperatura operativo -10/+50°C
1)
En el lado primaria de conmutación, 2ms.
Potenza nominale 6W.
Dispersione in stand-by solo 0,1 Watt.
Per montaggio in scatola da incasso o
a parete. Lunghezza 45mm, larghezza
55mm, profondità
33mm
.
Ingresso di tensione 230V (-20% fino a
+10 %).
Grado di efficienza:
SNT61-230V/12V DC-0,5A: 81%.
SNT61-230V/24V DC-0,25A: 82%
Tensione d'uscita stabilizzata ±1%,
ridotta ondulazione residua.
Protezione contro cortocircuito.
Protezione da sovraccarico e temperature
eccessive con disinnesco e riarmo auto-
matico dopo annullamento guasto
(funzione autorecovery).
Dati tecnici
Onda residua 100mV
Classe di protezione II
Grado di protezione IP20
Corrente di spunto
1)
18A/230V
Protezione sovraccarico 160-200%
temporanea
Protezione sovratensioni 140-170%
Quantità installabile, in parallelo
_
Temperatura di -10/+50°C
funzionamento
1)
Con accensione lato primari, 2ms.
Fuentes de alimentación
SNT61-230V/12V DC-0,5A y
SNT61-230V/24V DC-0,25A
E
Estos dispositivos electrónicos solo
pueden ser instalados por personal
autorizado. En otro caso existe peligro
de fuego o de descarga eléctrica.
Temperatura ambiental:
-10°C hasta +50°C.
Temperatura almacenaje:
-25°C hasta +70°C.
Humedad aire relativa:
Media anual <75%.
I
L'installazione di queste apparec-
chiature elettriche deve essere
eseguita soltanto da personale
qualificato, altrimenti c'è il pericolo
d'incendio o di scariche elettriche!
Temperatura nel luogo di installazione:
-10°C fino a +50°C.
Temperatura di deposito:
-25°C fino a +70°C
Umidità relativa: media annua <75%
Alimentatori
SNT61-230V/12V DC-0,5A e
SNT61-230V/24V DC-0,25A
61 000 164 - 161 000 164 - 1
Eltako GmbH
D-70736 Fellbach
+49 711 94350000
www.eltako.com
11/ 2 013
Reservado el derecho de modificación.
Guardarlo para el uso posterior!
Eltako GmbH
D-70736 Fellbach
+49 711 94350000
www.eltako.com
11/2013 Salvo modifiche
.
Conservare per un uso successivo!

Chat with your Eltako SNT61-230V/24VDC-0.25A manual using AI

Get instant AI answers from your Eltako SNT61-230V/24VDC-0.25A manual

Ask anything about the Eltako SNT61-230V/24VDC-0.25A. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend SNT61-230V/24VDC-0.25A?

Yes No

Frequently Asked Questions

A

The device supports an operating temperature between minus ten degrees Celsius and plus fifty degrees Celsius. It can withstand storage conditions down to minus twenty-five degrees and up to seventy degrees Celsius.

Is this answer helpful?

A

No, the protection degree is rated at IP20. This means it offers protection against solid objects larger than 12.5 mm but does not provide protection against water immersion or splashing.

Is this answer helpful?

A

Yes, it features an autorecovery function. If there is overload or overheating, the unit switches off and automatically reconnects once the fault is cleared.

Is this answer helpful?

A

Yes, these switching power supplies can be switched in parallel to increase total capacity. The number depends on specific system configuration and cooling requirements.

Is this answer helpful?

A

Only qualified electricians are permitted to install this electrical equipment. Improper installation carries a risk of fire or electrical shock.

Is this answer helpful?

A

The input voltage accepts 230 volts with a tolerance range of negative twenty percent to positive ten percent, allowing flexibility with mains fluctuations.

Is this answer helpful?

A

The efficiency for the 24V model is eighty-two percent. This high efficiency reduces waste heat and improves energy usage over time.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • High efficiency rating of up to 82 percent
  • Autorecovery function for quick fault resolution
  • Compact dimensions fit tight installation spaces
  • Low stand-by power consumption of 0.1 watt
  • Stabilized output voltage with plus-minus 1 percent tolerance
VS

Disadvantages

  • Installation restricted to skilled electricians only
  • Limited operating temperature range from minus 10 to plus 50 degrees
  • Not waterproof with only IP20 protection degree
  • Maximum output current of 0.25 ampere is relatively low
  • Requires primary side activation which affects startup current
M: QW-35-FL

Product Specification

Type

Power Supply

Standard

EnOcean, Wireless (868MHz)

Function

Power Supply

Dimensions

1.77x1.77x1.30in

Special Features

IP20

M: QW-35-FL

Product Description

Reliable Power Solutions for Modern Automation Systems

In today's complex building management environments, maintaining consistent electrical performance is vital for operational success. When selecting components, engineers prioritize devices that offer stability and safety. The Eltako SNT61-230V/24VDC-0.25A Switching power supply 24V, 0.25A stands out as a robust solution for powering control circuits efficiently. This specific unit delivers a precise output capable of handling various low-voltage applications within domestic and commercial settings. Its design ensures minimal energy waste while providing secure connections for sensitive equipment.

Technical Specifications and Performance

Understanding the hardware capabilities is essential before deployment. This unit operates with a rated capacity of six watts, making it suitable for smaller loads without excessive heat generation. Stand-by losses are incredibly low at just 0.1 watt, contributing to overall energy savings over long periods. The physical dimensions are compact, measuring 45 millimeters in length, 55 millimeters in width, and 33 millimeters in depth. This small footprint allows for easy integration into tight spaces behind panels or walls. Efficiency reaches up to 82 percent for this specific voltage configuration. Input voltage ranges from 230 volts minus 20 percent up to plus 10 percent, accommodating standard grid fluctuations safely.

Safety Features and Installation Guidelines

Safety is paramount when working with electrical infrastructure. The device includes an autorecovery function that resets automatically after temporary faults such as overloads or overheating occur. It also features short-circuit proof capabilities and class II protection standards. However, users must adhere to strict installation protocols. Only skilled electricians should handle the setup process to prevent fire hazards or electric shocks. Operating temperatures span from minus ten to plus 50 degrees Celsius. Proper ventilation is required to maintain these limits during continuous duty cycles. Regular maintenance checks help ensure longevity and safe operation throughout its service life.

Important Notes for Users

Always verify compatibility with existing systems before installation. Keep records of all specifications for future reference during troubleshooting sessions. Ensure mounting locations support the weight and thermal requirements specified by the manufacturer. Never modify the internal circuitry as this voids safety certifications and creates significant risks. Follow all local electrical codes to guarantee compliance and protect personnel from potential injuries.

M: claude-opus-5-5

© Copyright 2026 Manual.ly