Manual.ly Logo

Eltako FUD70S-230V Manual

0.0 · 0 Ratings

PDF manual · 2 Pages

English

M: qwen/qwen3.5-flash-20260224
page

/ 2

Loading...
a2fe63c9359e4af2b3ca92053225d3183a41 page 1
Universal dimmer switch, power MOSFET
up to 400 W. Automatic lamp detection.
With adjustable minimum brightness or
maximum brightness and dimming speed.
With switching operation for light alarm
clocks, children‘s rooms and snooze
function. Also with light scene control by
PC or wireless pushbuttons. Bidirectional
wireless and with repeater function.
Only 0.6 watt standby loss.
Mounting in the 230 V power supply cord,
e.g. in false ceilings. 100 mm long,
50 mm wide and 31 mm high.
With bidirectional wireless; in addition, a
repeater function can be switched in. Every
change in state and incoming central com-
mand telegrams are conrmed by a wirel-
ess telegram. This wireless tele gram can be
taught-in in other actuators, in the GFVS
software and in FUA55 universal displays.
Universal dimmer switch for lamps up to
400 W, depending on ventilation conditions.
Dimmable energy saving lamps ESL and
dimmable 230V LED lamps, additionally
depending on the lamps electronics.
Zero passage switching with soft ON and
soft OFF to protect lamps.
The brightness level is stored on switch-off
(memory). In case of a power failure the
switch position and the brightness stage
Wireless actuator
Universal dimmer switch
FUD70S-230V as cord switch
GB
Temperature at mounting location:
-20°C up to +50°C.
Storage temperature: -25°C up to +70°C.
Relative humidity:
annual average value <75%.
30 100 852 - 1
Only skilled electricians may install this
electrical equipment otherwise there is
the risk of re or electric shock!
valid for devices from production week
14/15 (see bottom side of housing)
are stored and may be switched on when
the power supply is restored.
Automatic electronic overload protection
and overtemperature switch-off.
Function rotary switches
The left rotary switch determines the
operation, whether automatic lamp detection
or special comfort positions should work:
AUTO allows the dimming of all lamp
types.
EC1 is a comfort position for energy saving
lamps, which which by design must be
turned on with an increased voltage so that
they switch on again in cold state
EC2 is a comfort position for energy saving
lamps, which by design won’t switch on
again when dimmed down. Therefore
Memory is switched off in this position.
LC1 is a comfort position for dimmable 230 V
LED lamps which are not being dimmed
down enough when set to AUTO (trailing
phase angle) dependent on the construction
and must therefore be forced to leading
phase angle.
LC2 and LC3 are comfort positions for
dimmable 230 V LED lamps like LC1, but with
different dimming curves.
In positions EC1, EC2, LC1, LC2 and LC3
inductive (wound) transformers may not
be used. In addition, the maximum number
of dimmable LED lamps may be lower by de-
sign than in the AUTO position.
The minimum brightness (fully dimmed
down) or maximum brightness (fully
dim med up) is adjustable with the middle
%
rotary switch. In the setting LRN up to
30 pushbuttons can be assigned, of which
one or more central pushbuttons.
The dimming speed is adjustable using the
right dimming speed rotary switch on the
side. At the same time, the soft ON and soft
OFF periods are changed.
The pushbuttons can be taught-in
either as direction switches or universal
switches:
When installed as a direction switch, one
side is then 'switch on and dim up' and the
other side is 'switch off and dim down'.
A double-click on the switch-on side activa-
tes automatic dim-up to full brightness at
dim speed. A double click on the switch-off
side activates the snooze function. The
children‘s room function is implemented on
the switch-on side.
As a universal switch, change the direction
by briey releasing the pushbutton. With
switching operation for children‘s rooms and
snooze function.
Switching for light alarm clocks: A wire-
less signal of a time clock which was
taught-in accordingly starts the wake up
function by switching on the light at the
lowest brightness level and dims up slowly
until the maximum level is reached.
Dependent on the set dim speed the wake
up time is between 30 and 60 minutes.
The dimming process is stopped by tapping
briey, e.g. on the hand-held transmitter.
At setting ESL the switching for light alarm
clocks is not possible.
Switching operation for children‘s rooms
(universal switch or direction switch on the
switch-on side): If the light is switched on
by holding down the pushbutton, it starts at
the lowest brightness level after approx. 1
second and dims up slowly as long as the
pushbutton is held down. The last saved
brightness level is not modied.
Snooze function (universal switch or
direction switch on the switch-off side):
With a double impulse the lighting is
dimmed down from the current dimming
position to the minimum brightness level
and switched off. The current dimming
position as well as the adjustable minimum
brightness level determine the dimming
time (max. = 60 minutes) which can be
reduced as required. It can be switched off
at any time by short-time control com-
mands during the lighting is dimmed down.
Light scenes on the PC are set and
retrieved using the Wireless Visualisation
and Control Software GFVS. A description
of the GFVS is at „eltako-wireless.com“. One
or several FUD70S devices must be taught
in on the PC as dimming switches with
percentage brightness values.
Lights scenes with wireless switches are
taught-in on the FUD. Up to four brightness
values are retrievable using a direct light
scene pushbutton (pushbutton with double
rocker, top left = light scene 1, top right =
light scene 2, bottom left = light scene 3 and
bottom right = light scene 4) and/or using a
sequential light scene pushbutton (push-
button or one half of a double pushbutton,
press top = next light scene, press bottom =
previous light scene).
If a wireless motion-brightness sensor
FBH is taught-in, the switching threshold
will be set with the right rotary switch while
teaching-in, in which, depending on the
brightness (in addition to the movement),
the lighting turns on with memory voltage
(approximately 30lux in the OFF position and
up to 300lux in the max position). If the FBH
is taught-in in the ON position, it will only be
evaluated as a motion detector. A delay of
1 minute is xed in the FBH.
If a wireless brightness sensor FHD60 is
taught-in, the switching threshold will be
set with the right rotary switch while
teaching-in, in which, depending on the
brightness, the lighting turns on or off
(approximately 0 lux in the OFF position and
up to 50 lux in the ON position). When falling
below the brightness threshold, it will be
turned on with memory value. It will be
turned off at a brightness > 200 lux.
The LED on the side behind the left rotary
switch performs during the teach-in
pro cess according to the operating
instructions. It shows wireless control com-
mands by short ickering during operation.
Technical data
Incandescent and up to 400 W
halogen
1)
lamps 230 V (R)
Inductive transformers (L) up to 400 W
2)3)
Electronic transformers (C) up to 400 W
2)3)
Dimmable energy up to 400 W
5)
saving lamps ESL
Dimmable 230 V LEDs up to 400 W
5)
Max./min. temperature +50°C/-20°C
4)
at mounting location
Standby loss (activ power) 0,6 W
1)
For lamps with 150 W max.
2)
Per dimmer it is only allowed to use max. 2 inductive
(wound) transformers of the same type, further-
more no-load operation on the secondary part is
not permitted. The dimmer might be destroyed.

Chat with your Eltako FUD70S-230V manual using AI

Get instant AI answers from your Eltako FUD70S-230V manual

Ask anything about the Eltako FUD70S-230V. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend FUD70S-230V?

Yes No

Frequently Asked Questions

A

Yes it supports dimmable 230V LEDs up to 400W depending on specific electronics and compatibility.

Is this answer helpful?

A

Only qualified electricians should install it to ensure safety and proper wiring without risk.

Is this answer helpful?

A

Yes the memory function keeps the last brightness and status automatically after voltage return.

Is this answer helpful?

A

Yes FBH and FHD sensors can be trained to trigger the dimmer based on occupancy and light.

Is this answer helpful?

A

It operates at 868.3 MHz with max 10 mW transmission power using Eltako radio compatible devices.

Is this answer helpful?

A

Yes GFVS software allows scene control and configuration via computer for centralized management.

Is this answer helpful?

A

The Memory feature retains the last used brightness level automatically without user intervention.

Is this answer helpful?

M: qwen/qwen3.5-flash-20260224

Advantages and Disadvantages

Advantages

  • Supports lamps up to 400W with Power MOSFET technology for efficient switching
  • Bidirectional radio with repeater function ensures reliable signal transmission
  • Memory function saves brightness settings even after power outage or switching off
  • Low standby power consumption of only 0.6 watts aids in daily energy savings
  • Compatible with PC software GFVS for complex scene creation and central control
VS

Disadvantages

  • Only qualified electricians should install the device to avoid fire or shock risks
  • Comfort settings limit maximum power to 100W for certain lamp types like LED
  • Inductive transformers cannot be used in specific comfort modes without risk of damage
  • Dimmable LED lamp compatibility depends heavily on the specific electronic ballast
  • Secondary side load disconnection is prohibited on inductive transformers to prevent destruction
M: qwen/qwen3.5-flash-20260224

Product Specification

Type

Actuator

Standard

EnOcean, Wireless Bus (868 MHz)

Function

Switch Actuator (on/off), Dimming Function

Topology

Bus

Dimensions

1.97x3.94x1.22in

Features

IP20

M: qwen/qwen3.5-flash-20260224

Product Description

Smart Home Lighting Control

The Eltako FUD70S-230V-rw Funkaktor Universal-Dimmschalter 230V offers a versatile solution for modern home automation systems. This relay with dimmer capability supports up to 400 watts using a robust Power MOSFET. It features automatic lamp recognition to ensure compatibility with various bulb types including halogen, LED, and energy-saving lamps. Installation is simple within the 230V power line setup, such as in drop ceilings. The device measures 100 mm long, 50 mm wide, and 31 mm high, fitting neatly into standard junction boxes.

Advanced Dimming Features

Users can adjust minimum and maximum brightness settings alongside the dimming speed using dedicated rotary controls. The device includes specific functions like nursery mode, sleep mode with a six-minute max dim, and an awakening light function to start softly with increasing brightness. Memory retention ensures brightness levels are saved after switching off or power cycles. The standby loss is minimal at 0.6 watts, contributing significantly to overall energy efficiency. Bidirectional radio communication allows for confirmation signals back to the central unit and repeater functionality to extend range across large properties.

PC and Remote Control

The unit integrates seamlessly with PC software like GFVS for comprehensive scene management and visualization. You can program up to four light scenes directly via radio buttons or remotely using dedicated transmitters. It supports external motion sensors and light sensors for fully automated control based on occupancy and daylight. Note that installation strictly requires a qualified electrician due to high voltage risks within the mains line. The device must be installed according to safety guidelines to prevent fire hazards or electric shock. Comfort settings optimize performance for specific lamp types but limit max power to 100 watts in some specific modes like EC1 or LC1.

Installation and Safety

Temperature ranges support indoor environments from -20C to +50C. Ensure no secondary side load is removed on inductive transformers as this may destroy the dimmer. The memory function keeps settings during power outages and restores state upon voltage return. Proper sensor training is vital for automation functionality to ensure signals are received and confirmed. The radio operates at 868.3 MHz with max 10 mW transmission power. Learning sensors involves specific dial positions for AUTO or LRN settings with LED indicators. Always verify the Eltako FUD70S-230V-rw Funkaktor Universal-Dimmschalter 230V, Schaltaktor mit Dimmer Manual specifications before starting work to understand the specific wiring steps and comfort mode distinctions.

Notes:

  • Only electricians should install.
  • Check lamp compatibility for LEDs.
M: qwen/qwen3.5-flash-20260224

© Copyright 2026 Manual.ly