Manual.ly Logo

Eltako EUD62NPN-IP/110-240V Manual

0.0 · 0 Ratings

PDF manual · 2 Pages

English

M: QW-35-FL
page

/ 2

Loading...
2dc649fcf59c93fec598ae63952a8e772014 page 1
Universal dimming actuator IP
EUD62NPN-IP/110-240V
Eltako Connect App download:
https://eltako.com/redirect/eltako-connect
Universal dimming actuator. With power
MOSFET.
Dimmable 230 V LED lamps in 'phase
cut-off' mode up to 300 W or in 'phase control'
mode up to 100 W depending on ventilation
conditions. 230 V incandescent lamps and
halogen lamps up to 300 W depending on
ventilation conditions
. No minimum load.
Only 0.7 watt standby loss.
For installation. 49 x 51 mm wide, 25 mm deep.
The terminals are plug-in terminals for
conductor cross-sections of 0.2 mm
2
to
2.5 mm
2
.
Zero passage switching with soft ON and
soft OFF to protect lamps.
Supply voltage, switching voltage and control
voltage local 110-240 V.
The brightness level is stored on switch-off
(memory).
built for
GB
30 062 002 - 2
Temperature at mounting location:
-20°C up to +50°C.
Storage temperature: -25°C up to +70°C.
Relative humidity:
annual average value <75%.
Only skilled electricians may install this
electrical equipment otherwise there is
the risk of  re or electric shock!
If
supp
l
y vo
l
tage
f
a
il
s, t
h
e
d
ev
i
ce
i
s sw
i
tc
h
e
d
off in de ned mode.
Automatic electronic overload protection and
overtemperature switch-off.
With control input for a mains voltage control
button that may be installed in front of it.
Glow lamp current is not permitted.
This actuator is Apple-certi ed and can
therefore be taught in Apple Home.
Typical connection
Add device to Apple Home:
ɀ Only 2.4 GHz Wi-Fi frequency bands are
supported.
ɀ Recommended: Commissioning close to
the main router.
2. Connected switch/button: press 8x brie y
(< 1 sec.) and 1x long (> 1.5 sec. and < 5 sec.).
A signal tone sounds for the last two short
closing actions.
The reset con rmation beeps are delayed by
15 seconds with this option.
! Outside of the time window, the device is
simply restarted !
Option 3:
1. The device is disconnected from the supply
voltage.
2. Apply supply voltage, wait for the signal
tone and disconnect the supply voltage
within 5 seconds.
3. Repeat step 2 a total of 5 times.
4. The sixth time the supply voltage is swit-
ched on, the successful factory reset is
con rmed by 3 short and 3 long beeps.
Over-the-Air (OTA) Firmware Updates:
ɀ If the device is connected to the Internet, it
will immediately search for possible updates.
Updates are then requested cyclically every
12 hours.
ɀ Data transfer between the Eltako update
server and the device meets the highest
security standards.
ɀ Before an update is installed, it is checked
whether it is correctly encrypted, validated
and undamaged.
ɀ Updates are downloaded and installed, but
only activated when no important process is
running and no load is switched. The restart
required for this takes a few seconds and
goes unnoticed.
ɀ If an update fails or leads to device insta-
bility, the system automatically switches
back to the previous  rmware version and
waits for a new update.
O ine rmware updates:
The device supports o ine rmware updates
via REST API. More information on this on the
product website.
1. Apply mains voltage and wait for the signal
tone.
2.
Wait 15 seconds until all modules have started.
3. Open the Apple Home app.
4. In the upper right corner press the '+' symbol
and select 'Add device'.
5. Scan the Apple Home QR code. It can be
found on the back of the device and on the
QR code card in the packaging.
6. The Apple Home app will guide you through
the remaining steps.
Important!
After a successful connection, an update is
automatically searched for, installed and the
device restarts.
Factory reset:
3 short and 3 long beeps will beep to con rm
the reset:
Option 1:
Via the Eltako Connect app.
Option 2:
1. Apply supply voltage
(time window of 5 minutes be
g
ins)

Chat with your Eltako EUD62NPN-IP/110-240V manual using AI

Get instant AI answers from your Eltako EUD62NPN-IP/110-240V manual

Ask anything about the Eltako EUD62NPN-IP/110-240V. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend EUD62NPN-IP/110-240V?

Yes No

Frequently Asked Questions

A

It operates on local supply, switching, and control voltages ranging from 110 to 240 volts. This ensures compatibility with various international electrical standards without needing a step-down transformer.

Is this answer helpful?

A

You need to open the Home app, scan the QR code on the back or card, and follow on-screen prompts. Ensure you are on a 2.4 GHz network before starting the setup process.

Is this answer helpful?

A

Yes, it handles dimmable LED lamps up to 300 watts in trailing edge mode. Leading edge mode supports up to 100 watts for LEDs. Performance depends on ventilation conditions.

Is this answer helpful?

A

The system automatically switches back to the previous firmware version immediately. It waits for a new update request rather than leaving the device in a potentially unstable state.

Is this answer helpful?

A

Yes, you can perform a factory reset via the app or by power cycling the device five times quickly. Success is confirmed by three short and three long beeps.

Is this answer helpful?

A

Yes, the device supports offline firmware updates via REST API. Apply mains voltage, wait for signal tones, and initiate the update procedure through the appropriate software interface.

Is this answer helpful?

A

Yes, the brightness level is stored on switch-off. When power is restored, the light returns to the previously memorized intensity level automatically.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Ultra-low standby loss of only 0.7 watts enhances energy efficiency significantly
  • Seamless integration with Apple Home and Works with Apple certification ensures broad compatibility
  • Memory function preserves brightness settings after power interruption for user convenience
  • Compact dimensions of 49 x 51 mm allow easy installation in tight junction boxes
  • Automatic overload protection and overtemperature switch-off safeguard equipment longevity
VS

Disadvantages

  • Maximum operating temperature limited to 50 degrees Celsius restricts outdoor hot climates
  • Supports only 2.4 GHz Wi-Fi networks requiring router configuration for 5 GHz bands
  • Inductive transformer usage restricted to two units per dimmer to prevent damage
  • Glow lamp current is strictly forbidden to avoid operational interference issues
  • Skilled electrician mandatory for installation to mitigate fire or shock risks
M: QW-35-FL

Product Specification

Type

Actuator

Standard

EnOcean, Wireless Bus (868MHz), Matter

Function

Switching Actuator (on/off), Dimming Function

Topology

Bus

Dimensions

1.93x2.01x0.98 in

M: QW-35-FL

Product Description

Modern Lighting Solutions

Welcome to the future of residential illumination with the Eltako EUD62NPN-IP/110-240V Universal Dimming Actuator, Switching Actuator with Dimmer series. This device represents a significant upgrade for smart home enthusiasts seeking precision and reliability. Integrated directly into your electrical setup, it allows for seamless control of various lamp types through wireless connectivity.

Users appreciate the low standby loss of just 0.7 watt when the unit is idle. This efficiency contributes to energy savings over time. The hardware supports both phase cut-off and phase control modes. You can dim 230 V LED lamps up to 300 W depending on ventilation. Incandescent and halogen lamps also reach up to 300 W limits. There is no minimum load requirement, making it versatile for mixed bulb setups.

Installation requires a skilled electrician due to mains voltage risks. The physical footprint is compact at 49 x 51 mm wide. It fits easily into standard junction boxes. Protection mechanisms include automatic electronic overload and overtemperature switches. This ensures longevity even under fluctuating grid conditions.

Integration with Apple Home is a standout feature. After connecting, the device searches for updates automatically. Firmware upgrades happen securely with encrypted data transfers. If an update fails, the system reverts safely to the previous version. Memory functionality retains brightness levels when power cycles occur. Offline firmware updates via REST API offer further flexibility for advanced users managing large installations remotely.

Network requirements specify 2.4 GHz frequency bands only. Five-second power cycling triggers factory resets if necessary. Voice commands work alongside app controls for flexible management. Connectivity confirms successful pairing through audible feedback signals indicating status. Proper mounting guarantees optimal airflow for thermal management. Glow lamp currents are strictly forbidden to prevent interference.

Relay switching utilizes zero passage technology to protect connected bulbs during activation. This prevents premature failure common in incandescent fixtures. The unit includes control inputs for external push buttons installed nearby. Safety remains the priority throughout the design lifecycle. Electrical compliance follows Directive 2014/53/EU standards globally. Maintenance is simplified through clear signal tones during commissioning. Whether retrofitting old homes or building new systems, this actuator delivers consistent performance without complexity. Enjoy enhanced ambiance control today.

M: QW-35-FL

© Copyright 2026 Manual.ly