Manual.ly Logo

EK Water Blocks EK-Quantum Volume FLT Manual

0.0 · 0 Ratings

PDF manual · 11 Pages

English

M: OA-GPT-54-NAN
page

/ 11

Loading...
bcc7c3a2697da4cce472ad03fa7f8a18153f page 1
INSTALLATION MANUAL
EKQuantum
Volume / Kinetic FLT

Chat with your EK Water Blocks EK-Quantum Volume FLT manual using AI

Get instant AI answers from your EK Water Blocks EK-Quantum Volume FLT manual

Ask anything about the EK Water Blocks EK-Quantum Volume FLT. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend EK-Quantum Volume FLT?

Yes No

Frequently Asked Questions

A

The reservoir uses a standard fan mounting hole pattern with 15mm spacing, matching EK radiators. The mounting holes use M4 threads with a maximum engagement of 10mm. Use compatible screws and avoid over-length hardware to prevent damage.

Is this answer helpful?

A

Yes. The reservoir can be positioned vertically or horizontally, depending on clearance and your build layout. Just ensure proper pump clearance and do not mount it when the pump is in a dead position.

Is this answer helpful?

A

Use one inlet and one outlet port. The device has multiple inlet and outlet ports, and only one of each should be used. All unused ports must be blocked using G1/4 plugs to keep the loop sealed and functioning properly.

Is this answer helpful?

A

Plug the 3-pin connector into the motherboard D-RGB header. The guide specifies a layout with +5V and a digital signal. Confirm that the connector arrow orientation matches the +5V line on your motherboard to avoid damage.

Is this answer helpful?

A

After filling and assembling the loop, run a leak test for 24 hours. Power only the pump using an external PSU, inspect all components for leaks, and allow for normal coolant level changes as air collects in the reservoir.

Is this answer helpful?

A

Place the reservoir above the pump. This helps ensure the system does not run without coolant and supports stable loop behavior during operation.

Is this answer helpful?

A

Use corrosion inhibiting coolants for liquid cooling systems. EKWB recommends EK-Cryofuel as a worry-free option for consistent performance and protection.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • Standard fan mounting hole pattern with 15mm spacing for easy compatibility with EK radiators
  • Supports flexible reservoir positioning with optional vertical or horizontal orientations
  • Uses o-ring based fittings that seal reliably with modest tightening force
  • Clear D-RGB connection method for straightforward motherboard lighting integration
  • Recommends a 24-hour leak test process to catch issues early
VS

Disadvantages

  • M4 thread engagement is limited to a maximum of 10mm
  • Using incorrect or longer screws, such as those intended for fans or radiators, may damage the reservoir
  • Unused ports must be blocked with G1/4 plugs or loop performance and safety can suffer
  • Incorrect D-RGB header orientation can damage the motherboard or LED strip
M: OA-GPT-54-NAN

Product Specification

Type

Reservoir

Material

Copper (nickel-plated), PMMA

Ports

G1/4"

Pump

N/A

Lighting

LED (RGB)

Color

clear (transparent), black (matte)

Special features

including bracket

M: GO-GEM-FL-25

Product Description

EK Water Blocks Quantum Line EK-Quantum Volume FLT (EK-Quantum Kinetic FLT) - Quantum-Grade Reservoir Setup

The EK Water Blocks Quantum Line EK-Quantum Volume FLT Manual style of guidance helps you install the EK-Quantum Volume / Kinetic FLT reservoir confidently, with clear attention to mounting, port routing, and safe testing. Built for liquid cooling loops, this FLT reservoir can be mounted in multiple orientations while keeping pump clearance in mind. It is designed around common EK radiator mounting standards, making integration straightforward for many custom watercooling builds.

Mount it your way

Thanks to a standard fan mounting hole layout with 15mm spacing, the reservoir can be attached to a chassis or other compatible mounting points. The mounting holes use standard M4 threads with a maximum engagement of 10mm. EK fittings are intended to be tightened with only modest force, relying on the included rubber o-ring gaskets for the liquid seal.

If you need more flexibility, EK also supplies FLT mounts that allow installation onto fans and radiators while preserving the required clearance for the pump. The reservoir can be positioned vertically or horizontally, and you can choose configurations using the supplied M4 hardware. A key placement tip: avoid mounting the reservoir when the pump is in a dead position, and keep the reservoir above the pump to reduce the risk of running without coolant.

Connect ports correctly

Port routing is essential. The FLT uses inlet and outlet ports such that one inlet and one outlet must be used. Any unused ports should be blocked with G1/4 plugs to prevent leaks or improper loop behavior. For the Volume FLT version with two ports usable as inlet or outlet, connect the chosen outlet directly to your pump, then fill the loop through the appropriate fill area.

Add D-RGB lighting safely

If your setup includes the D-RGB LED strip, connect the 3-pin connector from the water block to the motherboard D-RGB header. Make sure the wiring matches the header layout, including the +5V line and the digital signal. The connector orientation matters; incorrect placement can damage the motherboard or LED strip.

Test before powering up the full system

After assembly and filling, perform a leak test for 24 hours. Power only the pump via a PSU outside the system, let it run continuously, and inspect every connection. It is normal for the coolant level to drop during the first run as air accumulates in the reservoir. Ensure all components are completely dry before powering the full system.

Key results

  • Standard 15mm EK mounting layout with M4 threads supports flexible chassis and radiator placement
  • Correct port selection and blocking with G1/4 plugs helps maintain a safe, functional loop
  • Above-pump positioning and correct fitting torque supports stable coolant delivery
  • Proper D-RGB wiring (including +5V digital signal orientation) prevents lighting and hardware damage
  • 24-hour leak testing reduces the risk of hidden leaks after installation

Pros and cons (based on the installation guidance)

Pros

  • Standard fan mounting hole pattern with 15mm spacing for easier integration
  • M4 threads with known engagement limits help keep mounting safe
  • Multiple mounting orientations (vertical and horizontal) for better case fit
  • Recommended leak testing workflow improves reliability

Cons

  • Incorrect screw length or thread type can damage the product
  • Maximum M4 engagement is limited to 10mm
  • Unused ports must be blocked with G1/4 plugs
  • D-RGB header pinout and connector orientation must match exactly

Notes

  • Use corrosion inhibiting coolants; EK recommends EK-Cryofuel for worry-free usage.
  • Keep the reservoir positioned above the pump to avoid running without coolant.
  • Dry all hardware fully before powering other components.
M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly