Manual.ly Logo

EK Water Blocks EK-Quantum Vector RTX RE Ti Manual

0.0 · 0 Ratings

PDF manual · 11 Pages

English

M: OA-GPT-54-NAN
page

/ 11

Loading...
4ab4c36f6f74655759a1e823c9fc996262e0 page 1
INSTALLATION MANUAL
EKQuantum
Vector RTX RE / RE Ti / Titan RTX
GPU WATER BLOCK

Chat with your EK Water Blocks EK-Quantum Vector RTX RE Ti manual using AI

Get instant AI answers from your EK Water Blocks EK-Quantum Vector RTX RE Ti manual

Ask anything about the EK Water Blocks EK-Quantum Vector RTX RE Ti. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend EK-Quantum Vector RTX RE Ti?

Yes No

Frequently Asked Questions

A

The text specifies compatibility with RTX 2070, RTX 2080, RTX 2080 Ti, and Titan RTX. Always match the exact EK-Quantum Vector RTX RE Ti variant to the GPU model before ordering or installing.

Is this answer helpful?

A

Yes. The process includes removing the factory backplate and removing the stock cooler assembly and its screws, including fan-related connections. After removal, you must unplug fans (if applicable) and clean the PCB and components thoroughly.

Is this answer helpful?

A

The instructions recommend corrosion inhibiting coolants for liquid cooling systems, and state it is mandatory for nickel plated water blocks. This helps prevent corrosion inside the loop and preserves long-term reliability of the block and components.

Is this answer helpful?

A

The text explicitly says do not use pure distilled water. For best results, EK recommends using EK-CryoFuel coolants. Using the recommended coolant improves compatibility and helps maintain corrosion protection.

Is this answer helpful?

A

Some pads may be pre-cut, while others must be cut to cover VRM parts such as coils, MOSFETs, and drivers. Remove protective foil from both sides before installation, then place pads by the specified thicknesses and locations so the VRM section receives proper coverage.

Is this answer helpful?

A

EK advises temporarily removing the water block to check for uniform surface contact, with special attention to the VRM section. If contact is not correct, confirm thermal pad thickness and placement, then re-attach the block and re-check.

Is this answer helpful?

A

Plug the 3-pin connector from the Monoblock D-RGB LED strip into the motherboard D-RGB header. Make sure the arrow on the connector is oriented to the +5V line indicated by the motherboard. Incorrect orientation can damage the motherboard or LED strip.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • Full-cover cooling that targets the GPU core and VRM components using thermal pads and EK-TIM.
  • Includes guidance for correct thermal pad sizing, foil removal, and mounting alignment to help ensure even contact.
  • Compatible with listed RTX and Titan RTX graphics cards for flexible loop building.
  • Supports D-RGB via a 3-pin LED strip connection with motherboard +5V alignment.
  • Uses G1/4 threaded fittings and recommends EK fittings to support secure tubing connections.
VS

Disadvantages

  • Installation is intended only for expert users; improper mounting may damage the GPU or hardware.
  • Requires careful cleaning, thermal compound application, and correct pad placement for best performance.
  • Too much mounting force can crack GPU chip dies.
  • Cooling performance depends on thorough air bleeding and verified block contact.
  • Must use corrosion inhibiting coolant and avoid pure distilled water, especially for nickel plated variants.
M: OA-GPT-54-NAN

Product Specification

Type

GPU

Compatibility

NVIDIA GeForce RTX 2080 Ti

Connectors

G1/4"

Special features

Voltage converter co-cooled (GPU)

M: GO-GEM-FL-25

Product Description

EK Water Blocks Quantum Line EK-Quantum Vector RTX RE Ti - Full-Cover GPU Cooling with D-RGB

Designed for demanding GeForce builds

The EK Water Blocks Quantum Line EK-Quantum Vector RTX RE Ti is a full-cover GPU water block made to cool not only the graphics core, but also the surrounding VRM areas. Built for RTX-class cards listed in the EK-Quantum Vector lineup, it is intended for liquid cooling loops that prioritize clean thermals and reliable contact across the entire GPU package.

This cooling solution is part of the EK ecosystem described in the EK Water Blocks Quantum Line EK-Quantum Vector RTX RE Ti Manual. It emphasizes careful preparation, correct pad placement, and leak-safe assembly, so your block can reach its intended performance.

What you do before mounting matters

Start by removing the factory backplate and stock cooler components, then thoroughly clean all old thermal compound residue. EK recommends using denatured alcohol for removing TIM leftovers, followed by applying the included EK-TIM thermal grease using a blob or line approach for best results.

The block relies on correctly sized thermal pads for memory and VRM components. Some pads are pre-cut, while others must be cut to match coverage requirements such as coils, MOSFETs, and drivers. Before installation, remove protective foil from both sides of each thermal pad.

Mounting, contact checks, and leak-ready tubing

When placing the block, align the mounting holes carefully and avoid pressing too hard, since GPU chip dies can crack if excessive force is used. EK also advises temporarily removing the block to verify uniform contact, paying special attention to the VRM section.

Once mounted, install the included G1/4 fittings and connect your tubing to integrate the block into your cooling circuit. EK recommends EK fittings with the EK-Vector series, and notes important cautions when using non-EK connectors, including the maximum allowed male G1/4 thread length. Finally, bleed air thoroughly so you achieve optimal performance.

RGB integration for the finishing touch

If you want visual effects, connect the 3-pin connector for the D-RGB LED strip to the motherboard header. Ensure the arrow direction aligns with the +5V line to prevent damage to the motherboard or LED strip.

Key outcomes

  • Full-cover cooling across core and VRM using precision pads and EK-TIM for stronger thermal transfer.
  • Stable results after contact verification and complete air bleeding.
  • Secure loop integration with G1/4 fittings and proper inlet/outlet port usage.
  • Safe D-RGB operation when the connector is oriented to the correct +5V line.

Notes

  • Installation is intended for expert users only; improper mounting may damage hardware.
  • Use corrosion inhibiting coolants, and it is mandatory for nickel plated blocks.
  • Do not use pure distilled water; EK recommends EK-CryoFuel for best results.
M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly