Manual.ly Logo

EK Water Blocks EK-Loop Heat Gun Manual

0.0 · 0 Ratings

PDF manual · 100 Pages

English

M: gpt-5.6-terra
page

/ 100

Loading...
394922b7e1dd8663f8301adab1c20108f560 page 3
- 3 -
MODELS
- EK-Loop Heat Gun 2000W - EU Plug
- EK-Loop Heat Gun 2000W - UK Plug
- EK-Loop Heat Gun 1500W - US Plug
PACKAGE CONTENT
Check the heat gun, the power cord and the power plug for transportation damages.
WARNING: Packing materials are not toys! Children must not play with plastic bags!
Danger of suffocation!
• Heat gun (1 piece)
• Instruction manual (1 piece)
When parts are missing or damaged, please contact your dealer.
SAFETY WARNINGS
Read, understand and follow all safety rules and operating instructions in this manual before
using this product.
Accordance to International Standard EN 60335-1
• This heat gun is intended for domestic use only and not for commercial applications.
• This heat gun cannot be used by children or persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge.
• Children shall not play with the heat gun.
• Cleaning and user maintenance shall not be made by children.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
• A fire may result if the heat gun is not used with care, therefore:
• be careful when using the heat gun in places where there are combustible materials;
• be aware that heat may be conducted to combustible materials that are out of sight;
• do not use in presence of an explosive atmosphere;
• do not apply to the same place for a long time;
• do not leave the heat gun unattended when it is switched on;
• place the heat gun on its stand after use and allow it to cool down before storage.
INTENDED USE
Your heat gun has been specially designed tool for bending acrylic and PETG tubing only.
The heat gun has two settings:
1. Low heat (position 1): for use where the work surface or surrounding must not be allowed
to get too hot.
2. High heat (position 2): for faster heat up time of the work surface where you can also
operate the gun at a greater distance.

Chat with your EK Water Blocks EK-Loop Heat Gun manual using AI

Get instant AI answers from your EK Water Blocks EK-Loop Heat Gun manual

Ask anything about the EK Water Blocks EK-Loop Heat Gun. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend EK-Loop Heat Gun?

Yes No

Frequently Asked Questions

A

It is specifically designed for bending acrylic and PETG hard tubing used in custom PC liquid-cooling systems. It is not intended for general heating tasks, heating liquids, or use as a hair dryer.

Is this answer helpful?

A

Hold tubing with a silicone bending insert approximately 5 cm, or 2 inches, from the nozzle. Slowly rotate the tube and move it side to side to heat the material evenly before forming the bend.

Is this answer helpful?

A

Mode I operates from 60 C to 350 C with 300 l/min airflow. Mode II operates from 60 C to 600 C with 500 l/min airflow. The maximum 600 C setting is only available in mode II.

Is this answer helpful?

A

The US-plug model is rated at 1500 W on 120 V power. It offers 140 F to 572 F in mode I with about 11 cfm airflow, and 140 F to 932 F in mode II with about 18 cfm airflow.

Is this answer helpful?

A

A silicone bending insert supports the inside of the heated tube, helping it retain a smooth profile during bending. It reduces the risk of kinks and supports cleaner, more consistent curves.

Is this answer helpful?

A

Switch it off, place it upright on a level surface using its stand, and allow it to cool completely before storage. Never place the tool on its side, cover the air intake, or leave it unattended while hot.

Is this answer helpful?

M: gpt-5.6-terra

Advantages and Disadvantages

Advantages

  • Purpose-built for bending acrylic and PETG hard tubing in custom liquid-cooling loops.
  • Two heat and airflow modes support gentle warming or faster heating for different bending tasks.
  • Dedicated plus and minus controls and a colored display simplify temperature selection.
  • Available in EU, UK, and US plug versions for regional power compatibility.
  • Compatible with EK-Loop Modulus bending tools in 12 mm, 14 mm, and 16 mm sizes.
VS

Disadvantages

  • Designed for domestic use only and not intended for commercial applications.
  • Temperature changes in fixed increments, limiting ultra-fine adjustment.
  • Overheating tubing can cause bubbles, discoloration, and diameter deformation.
  • The nozzle stays hot for up to 30 minutes after use, requiring careful cooldown handling.
  • Package content is limited to the heat gun and instruction manual.
M: gpt-5.6-terra

Product Specification

Type

Pipe bending accessory

M: gpt-5.6-terra

Product Description

EK Water Blocks EK-Loop Heat Gun - Read, Download & Print Free

The EK Water Blocks EK-Loop Heat Gun is a purpose-built tool for custom liquid-cooling enthusiasts who need clean, controlled bends in acrylic and PETG hard tubing. Designed for domestic use, it delivers adjustable hot air for shaping tubing with greater consistency, helping builders create precise runs for visually polished PC water-cooling loops.

Controlled Heat for Hard-Tube Bending

This EK-Loop tool features two operating modes that combine temperature and airflow settings. On EU and UK versions, mode I provides a range of 60 C to 350 C with 300 l/min airflow, while mode II reaches 60 C to 600 C at 500 l/min. The US version offers 140 F to 572 F in mode I and up to 932 F in mode II, with airflow of approximately 11 or 18 cfm.

Temperature is adjusted through dedicated plus and minus controls. Mode I changes in 30 C or 86 F increments, while mode II changes in 55 C or 131 F increments. A colored incremental display provides a quick visual reference for the selected heat level, making it easier to choose a setting appropriate for the tubing and the bend you want to form.

Designed Around the EK-Loop Workflow

For smoother results, place a silicone bending insert inside the tube before heating. Keep the tube roughly 5 cm or 2 inches from the nozzle, rotate it slowly, and move it side to side to distribute heat evenly. Once the material becomes flexible, shape it to the required angle. Even heating is important: excessive exposure may cause bubbles, discoloration, or unwanted changes to tube diameter.

The unit should always stand upright on a level, heat-resistant surface during use and while cooling. Its plastic-and-rubber housing, 2 m cable, double-insulated construction, and two-mode control system support a practical workstation setup for PC builders. EK also recommends compatible EK-Loop Modulus Hard Tube Bending Tools in 12 mm, 14 mm, and 16 mm sizes for more repeatable bends.

Safety and Care Notes

This heat gun produces serious heat and requires attentive handling. Keep vents clear, provide good ventilation, keep combustible materials away, and never leave it operating unattended. Do not use it in damp or explosive environments, point it at people, or treat it as a hair dryer. The metal nozzle can remain hot for up to 30 minutes after use.

Before cleaning or maintenance, disconnect the power supply. Keep ventilation openings free of dust and wipe the housing with a soft cloth. Avoid harsh solvents that may damage plastic parts. With careful operation, the EK Water Blocks EK-Loop Heat Gun offers a focused solution for shaping hard tubing in custom cooling projects.

M: gpt-5.6-terra

© Copyright 2026 Manual.ly