Manual.ly Logo

Einhell TE-TC 18/115 Li Manual

0.0 · 0 Ratings

PDF manual · 219 Pages

English

M: OA-GPT-5-NAN
page

/ 219

Loading...
e3d80edde6692fe616aa3bac707d81c30911 page b
D
- 11 -
9.6 Gehrungsschnitt (22,5°; 45°)
(Abb. 14a,14b,15)
•
Befestigen Sie die Wasserbehälter Abde-
ckung (6) in der gewünschten Winkelposition
(siehe Punkt 9.5 Winkeleinstellung für Geh-
rungsschnitt) (Abb. 14a, 14b).
•
Befestigen Sie den Parallelanschlag über
die Fixierungsklammern (10), wie in Bild 15
dargestellt.
•
Legen Sie die Fliese mit der Glasurseite auf
die Wasserbehälter Abdeckung (Abb.15).
•
Abbildung 15 zeigt die korrekte Position der
Hände während des Gehrungsschnitts. Die
linke Hand hält das Werkstück in Kontakt mit
der Trennscheibe, während die rechte Hand
das Werkstück vorschiebt. Der Vorschub
muss der Schneidekapazität der Trennschei-
be entsprechen. Auf diese Weise ist sicherge-
stellt, dass sich kein Material ablöst, was Un-
fälle oder Verletzungen verursachen könnte.
•
Führen Sie einen Probeschnitt mit einem
Fliesenrest durch, um das Schnittergebnis
beurteilen zu können.
Hinweis! Beim Blockieren der Trennscheibe, Ge-
rät ausschalten und Akku entfernen, erst dann
das Werkstück entfernen
10. Reinigung, Wartung und
Ersatzteilbestellung
Gefahr!
Ziehen Sie vor allen Reinigungsarbeiten den
Akku heraus.
Vor jeglicher Einstellung, Instandhaltung oder
Instandsetzung Akku herausziehen.
10.1 Reinigung
•
Halten Sie Schutzvorrichtungen, Luftschlitze
und Motorengehäuse so staub- und schmutz-
frei wie möglich. Reiben Sie das Gerät mit
einem sauberen Tuch ab oder blasen Sie es
mit Druckluft bei niedrigem Druck aus.
•
Wir empfehlen, dass Sie das Gerät direkt
nach jeder Benutzung reinigen.
•
Reinigen Sie das Gerät regelmäßig mit einem
feuchten Tuch und etwas Schmierseife. Ver-
wenden Sie keine Reinigungs- oder Lösungs-
mittel; diese könnten die Kunststoffteile des
Gerätes angreifen. Achten Sie darauf, dass
kein Wasser in das Geräteinnere gelangen
kann. Das Eindringen von Wasser in ein Elek-
trogerät erhöht das Risiko eines elektrischen
Schlages.
10.2 Kohlebürsten
Bei übermäßiger Funkenbildung lassen Sie die
Kohlebürsten durch eine Elektrofachkraft über-
prüfen.
Gefahr! Die Kohlebürsten dürfen nur von einer
Elektrofachkraft ausgewechselt werden.
10.3 Wartung
Im Geräteinneren befi nden sich keine weiteren zu
wartenden Teile.
10.4 Ersatzteilbestellung:
Bei der Ersatzteilbestellung sollten folgende An-
gaben gemacht werden;
•
Typ des Gerätes
•
Artikelnummer des Gerätes
•
Ident-Nummer des Gerätes
•
Ersatzteilnummer des erforderlichen Ersatz-
teils
Aktuelle Preise und Infos fi nden Sie unter
www.Einhell-Service.com
11. Entsorgung und
Wiederverwertung
Das Gerät befi ndet sich in einer Verpackung um
Transportschäden zu verhindern. Diese Verpa-
ckung ist Rohstoff und ist somit wieder verwend-
bar oder kann dem Rohstoff kreislauf zurückge-
führt werden. Das Gerät und dessen Zubehör
bestehen aus verschiedenen Materialien, wie z.B.
Metall und Kunststoff e. Führen Sie defekte Bau-
teile der Sondermüllentsorgung zu. Fragen Sie im
Fachgeschäft oder in der Gemeindeverwaltung
nach!
12. Lagerung
Ziehen Sie den Akku ab. Lagern Sie das Gerät
und dessen Zubehör an einem dunklen, trocke-
nen und frostfreiem sowie für Kinder unzugäng-
lichem Ort. Die optimale Lagertemperatur liegt
zwischen 5 und 30 ˚C. Bewahren Sie das Elektro-
werkzeug in der Originalverpackung auf.
13. Transport
Wenn Sie das Gerät an einen anderen Ort trans-
portieren wollen, ziehen Sie den Akku ab und stel-
len Sie es an einem anderen dafür vorgesehenen
Bereich auf.
Anl_TE_TC_18_115_Li_SPK13.indb 11Anl_TE_TC_18_115_Li_SPK13.indb 11 12.08.2021 16:46:5412.08.2021 16:46:54

Chat with your Einhell TE-TC 18/115 Li manual using AI

Get instant AI answers from your Einhell TE-TC 18/115 Li manual

Ask anything about the Einhell TE-TC 18/115 Li. Answers come from this manual, with the pages they are based on.

TE-TC 18/115 Li Maintenance Schedule

After every use
Clean the device immediately after use

Wipe with a clean cloth or blow out with low-pressure compressed air to keep safety devices and motor housing free of dust.

Show in the manual (page 11)
Regularly
Clean equipment with moist cloth

Use a damp cloth and mild soap. Do not use solvents and ensure no water enters the device interior.

Show in the manual (page 11)
During operation
Check wearing parts and fastenings

While running, check wearing parts and tighten any loose fasteners or verify accessory installation.

When excessive sparking occurs
Have carbon brushes checked by electrician

If excessive sparking occurs, only a qualified electrician may inspect or replace the carbon brushes.

Show in the manual (page 11)
M: QW-35-FL

Ask a Question

0/1000

Do you recommend TE-TC 18/115 Li?

Yes No

Frequently Asked Questions

A

The machine is sold as a stationary 'solo' unit and does not include a battery or charger. It must be used only with Einhell Power X-Change Li‑Ion batteries and charged with compatible Power X chargers.

Is this answer helpful?

A

The cutter uses a 115 mm diameter diamond cutting wheel with a 22.2 mm bore. Only continuous diamond cutting wheels suited for wet tile cutting are permitted; segmented diamond wheels are explicitly forbidden.

Is this answer helpful?

A

Fill the water reservoir to the MAX mark before cutting and monitor the level during use so the diamond segment remains submerged for cooling. Refill directly into the trough and drain via the water drain screw when finished.

Is this answer helpful?

A

Wear safety goggles, a dust mask, hearing protection, and gloves. Always remove the battery before maintenance or blade changes, ensure guards are installed, and avoid cutting materials the machine isn't designed for (e.g., wood or metal).

Is this answer helpful?

A

Remove the battery, drain the water if needed, lift the wheel guard, block the motor shaft with the counterholder, loosen the nut with the ring spanner, replace the blade observing rotation direction, and retighten before restoring guards.

Is this answer helpful?

A

The cutter delivers a maximum cutting height of approximately 24 mm at 90° and 16 mm at 45°. Cut length is effectively unlimited, governed by the workpiece and proper feed control.

Is this answer helpful?

A

Clean the unit after each use, keep air vents and guards free of debris, check wear parts and fastenings regularly, avoid full battery discharge, and store batteries charged (~40% minimum) in dry conditions between +10°C and +40°C.

Is this answer helpful?

M: OA-GPT-5-NAN

Advantages and Disadvantages

Advantages

  • Cordless convenience with Power X-Change compatibility for portable, workshop-free use.
  • Water-cooled diamond blade reduces dust and extends blade life for cleaner cuts.
  • Tilting table supports jolly and miter cuts up to 45° for versatile tile profiling.
  • Compact and lightweight (≈3.4 kg) while still offering a 305×335 mm cutting table.
  • Clear scale, parallel and miter stops enable repeatable, accurate cuts for DIYers.
VS

Disadvantages

  • Sold as a body-only unit—batteries and charger are not included, adding to total cost.
  • Not designed for heavy professional or industrial use; warranty may be void for commercial use.
  • Noise and vibration levels are significant; hearing protection and care are required.
  • Only specific diamond blades allowed; segmented blades are forbidden, limiting blade choices.
  • Requires regular water management and cleaning to avoid motor or electrical damage.
M: OA-GPT-5-NAN

Product Specification

Battery

18V, Li-Ion

No-load speed

3800 rpm

Disc diameter

4.53 in

Cutting capacity

0.94 in (90°), 0.63 in (45°)

Miter cuts

45°/45° left/right

Tool mounting

Bore 0.87 in

Special features

Angle stop, Wet cutting function, Parallel stop

Dimensions (WxD)

13.19x12.01 in

Weight

7.72 lb

Scope of delivery

without charger and battery, incl. diamond cutting disc

M: OA-GPT-54-NAN

Product Description

Einhell TE-TC 18/115 Cordless Tile Cutter, stationary solo Manual

The Einhell TE-TC 18/115 cordless tile cutter is a compact, battery-powered stationary cutting machine designed for precise cutting of small to medium tiles. Lightweight at about 3.4 kg and powered by an 18 V Power X-Change lithium-ion battery (sold separately), it features a 115 mm diamond cutting wheel, a water-cooled trough, and a tilting work surface for jolly and miter cuts up to 45°. The cutter’s table measures 305 x 335 mm and it delivers cutting heights of 24 mm at 90° and 16 mm at 45°. With an idle speed of 3,800 rpm and clear scale markings, the unit balances portability and accuracy for DIYers and hobbyists handling ceramic and glazed tiles.

Key features and operation

This cordless tile cutter includes a parallel stop and miter stop for repeatable cuts, a wheel guard with splitter for safety, and a water reservoir with a removable cover to cool the diamond blade and reduce dust. It supports unlimited cut length relative to the workpiece feed and allows jolly cuts by tilting the cutting surface. The cutter is designed to accept Power X-Change batteries and must be used only with compatible chargers. LED charger status indicators and guidance for battery care are provided: keep batteries charged above 40% in storage and avoid full deep discharge to extend life.

The machine requires correct assembly before use: mount the diamond wheel with proper flange orientation, install the splitter so it aligns behind the blade, and secure the wheel guard. Always remove the battery before maintenance, blade changes, or adjustments. During operation, keep the water level at or below the MAX mark so the diamond section is covered, and feed the tile at a rate appropriate to the blade capacity to avoid chipping or kickback.

Safety and maintenance

The manual emphasizes personal protective equipment: eye protection, dust mask, hearing protection, and gloves. Noise and vibration levels are specified (approx. 80.6 dB(A) sound pressure, 93.6 dB(A) sound power), so hearing protection is recommended. Only undamaged, correctly mounted diamond cutting wheels are permitted; segmented blades are forbidden. Regular cleaning after each use, checking fastenings and wear parts (such as carbon brushes and the cutting wheel), and preventing water ingress into the motor are stressed. Replacement parts and service contacts are available via Einhell Service; a 24-month warranty applies to consumer purchases under specified conditions.

Notes

  • The machine is not intended for cutting wood or metal; misuse voids warranty.
  • Always remove the battery before assembly, maintenance, or transport.
  • Use only Power X-Change batteries and Power X chargers.
  • Keep water level sufficient to cool the diamond edge during cuts.
  • For prolonged battery life, recharge before the battery is fully discharged.
M: OA-GPT-5-NAN

© Copyright 2026 Manual.ly